Question about Honda Civic

Open Question

How do I fix abs and brake light that stays on

ABS and Brake light stays on how do I reset lights

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 62 Answers

SOURCE: 2002 Mazda Protege ABS & Brake light

It is most likely caused by one of the ABS wheel speed sensors, those little cylindrical nipples on the back of your rotors with the cable attached to them. One way to confirm it is to read out the OBD2 codes for the ABS system, but there are some checks you can do. Visually check all four cables and sensors , and make sure there is no build up on the sensors. Make sure that the connector they plug into has good connections. Look at the wheel speed sensor and make sure the gap between the sensor head and the sprocket is the same on all four wheels (should be no more than a mm). Disconnect the wheel speed sensor cable and use an ohm-meter to check the resistance of all four sensors (they should all be similar, but don't remember the value exactly). There is a way to just disable the ABS by pulling out the 60A fuse, but if you do that you may have to plug in a code reader and use a grounding jumper on the ABS electical access box (don't remember which pin) to reset the ABS faults, otherwise you won't be able to drive around like that because your engine rpm at high speeds will behave erratically. Also, do not drive around without fixing this problem or bypassing ABS completely because it could get you into an accident. My ABS problem was intermittent, and the ABS would sometimes kick in on completely dry pavement as soon as I touched the break pedal, it almost caused me to rear-end a car on couple of occasions.

Posted on Jul 30, 2008

  • 3 Answers

SOURCE: abs brake problem

I found my solution on the web a few years ago. My 2002 RVS had permanent ABS lights and no ABS.

It was suggested to check the ABS electrical connections at the brake disks . There are quick connects there and I found a corroded connector on the front passenger side. My wife started the RVS and put it in gear. With the brake pedal pressed, I wiggled the connectors and the ABS light went "off and on" right away. I replaced the connector and it never happened again. It is likely 4 years ago.

Worth a try.

Posted on Jan 10, 2009

Monster80
  • 460 Answers

SOURCE: 2001 chevy s10 blazer abs light stays .

The abs is a add on for the brakes that when the tires come into a skid or slid they wont lock up..Your brakes will still work great with the abs disabled but your brakes will lock up if you push on the brakes hard enough to stop.Mainly abs works in slippery conditions not letting the tires lock up and keep the car rolling instead of making it slide..But no effect of the brakes will happen..Just make sure your fluid is full and there are no leaks and if you want to get them check you can stop by your local Auto Zone and they will scan your car for free and tell you what sensor is bad..I hope this was helpful to you...Have a great night

Posted on Apr 03, 2009

csmock132
  • 4669 Answers

SOURCE: abs brake lights come on and stay on

Replace the speed sensor in the rear end.

Posted on Apr 05, 2009

sledge1863
  • 149 Answers

SOURCE: ABS brake light comes on.

No there is no reset, sounds like you have a bad ABS sensor on one of the wheels. Only way to tell is to get it to a brake shop or dealer to check it. Good luck dont forget to rate.

Posted on Apr 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abslight stays on. How to fix? This is a2007trailblazer?


First you need to have EBCM - electronic brake control module check for DTC'S - diagnostic trouble code's . If the light is on there is a code stored . I think most part stores can do this and for free . After you find out what code is stored , looking up that code in service repair information for diagnostic trouble shooting chart would be next step . There are a few codes too.
DTC C0035 or C0040
DTC C0045 or C0050
DTC C0110
DTC C0131
DTC C0161
DTC C0186
DTC C0196
DTC C0201
DTC C0240
DTC C0241 or P0856
DTC C0244 or P1689
DTC C0245
DTC C0283
DTC C0287
DTC C0290 or C0292
DTC C0455
DTC C0550
DTC C0558

Find the code do the diagnostic's , fix the problem , wiring issue's , a sensor , bad module ,what ever it is . The light will go out then . Here is a sample of code discription .
• DTC C0035 Left Front Wheel Speed Sensor Circuit
• DTC C0040 Right Front Wheel Speed Sensor Circuit

Dec 30, 2016 | 2007 Chevrolet Trailblazer

2 Answers

Why does my ABS light stays on and sometimes i get a vibration in the brake petal causing my 2002 Cadillac escalade not wanting to stop?


Sounds like a fault with the Antilock Braking System. The vibration in the pedal is the ABS working. With your foot on the brake pedal, it releases and re-applies the brakes to stop a skid from the wheels locking up. You need professional service for brakes.

Seems to be a known issue on all Cadillac and requires the ABS module to be replaced.

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > DeVille Cadillac DeVille ABS Light Due to ABS Control Module Failure. This is a verified problem based on 126 reports. Learn more about this problem, when it occurs ...

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > Seville STS Traction control and ABS lights stay on dash. This is due to ecbtm Module gone bad. replace Module and this should fix the problem. You can go by the VIN and ...

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > DeVille DTS ABS Light Due to Control Module Failure on Cadillac DeVille DTS. The anti-lock ... ABS and Traction control light stays on. ... abs light to abs control stay on.

ABS Light Due to ABS Control Module Failure : Cadillac ...

repairpal.com > Problems > Cadillac > Seville SLS ABS Light Due to Control Module Failure on Cadillac Seville SLS. The anti-lock brake ... SLS135,000Jumsee. Abs and traction lights stay on when started.

Jan 12, 2016 | Cadillac Cars & Trucks

1 Answer

How to reset brake lite on my 2005 X type jaguar?


which brake warning light is on? the xtype does not have pad wear sensors fitted. so i guess you mean the abs light or the handbrake light.more than likely its the abs light and the common problem is the reluctor rings on one or the other of the rear outer constant velocity joints corroded/ fell off get the fault codes out of the abs module to help.

Aug 22, 2015 | 2005 Jaguar X-Type

1 Answer

Abs light stays on and brake light on 98 durango


The regular brake warning light is for the parking brake being applied or the brake fluid is low. You would need to get the abs system scanned for trouble codes to proceed.

Feb 20, 2014 | 1998 Dodge Durango

1 Answer

91 Buick park avenue abs light. This happened after my friend was driving down the freeway and his tire blew. Now it just blew the rubber off and he was able to drive t off the freeway on the belts. And...


ABS LIGHT AND MODULE TROUBLESHOOTING:



Anti lock brake system light comes up when there is issue with car brake systems. It can be low brake fluid or faulty ABS fuse or its issue with brake system or assembly. Your vehicles brake system needs inspection.


To troubleshoot these issues, I suggest you to refer the help links provided below. There are direct links with accurate solution, for these specific issues.


Click the link below and follow the procedure: ------


All types of ABS LIGHT / brake problems and repairs

http://howtobyme.blogspot.com/2011/11/abs-and-service-light-comes-on.html

-------------------


ABS light stays on but brakes work fine?

http://howtobyme.blogspot.com/2011/11/abs-light-stays-on-but-brakes-work-fine.html

----------------

VCS and ABS lights go on and off intermittently on Lexus?

http://howtobyme.blogspot.com/2011/11/vcs-and-abs-lights-go-on-and-off.html

-------------

The ABS and Traction Control Lights stays ON dash of car?

http://schematicsdiagram.blogspot.com/2011/06/abs-and-traction-control-lights-stays.html

-------------

ABS & Brake lights warning indicator steady on dash and speedometer not working for Dodge Ram?

http://howtobyme.blogspot.com/2011/11/abs-brake-lights-warning-indicator.html

-----------------------

Battery Light and ABS Light on Dash

http://whoisbyme.blogspot.in/2012/07/battery-light-and-abs-light-on-dash.html

-------------

Sometimes ABS light comes on while Driving?

http://howtobyme.blogspot.com/2011/12/sometimes-abs-light-comes-on-while.html

-----------

How Anti-Lock Brakes Work?

http://technoanswers.blogspot.com/2011/11/how-anti-lock-brakes-work.html

-------------

Brake System Troubleshooting?

http://technoanswers.blogspot.com/2011/11/brake-system-troubleshooting.html

-------------

Anti-lock brake light stays on all the time?

http://technoanswers.blogspot.com/2012/01/anti-lock-brake-light-stays-on-all-time.html

-------------------

ABS light comes on and Car makes Grinding noise?

http://repairhelpcenter.blogspot.com/2012/01/abs-light-comes-on-and-car-makes.html

---------------

ABS trouble codes for all models?

http://repairhelpcenter.blogspot.com/2011/11/abs-trouble-codes-for-all-1994-00-acura.html
------------

2008 Toyota Highlander: ABS warning light Blinking and OBD Error codes Coming?

http://technoanswers.blogspot.in/2012/05/2008-toyota-highlander-abs-warning.html

--------------

2003 Lexus ES: VSC, TRAC OFF, ABS lights ON?

http://technoanswers.blogspot.in/2012/04/2003-lexus-es-vsc-trac-off-abs-lights.html

----------------

2008 Toyota Highlander Hybrid: Warning Lights Abs, Vsc & Brake Are On?

http://technoanswers.blogspot.in/2012/04/2008-toyota-highlander-hybrid-warning.html

-------------

ABS & Brake warning lights remains steady on dash?

http://schematicsdiagram.blogspot.com/2011/12/abs-brake-warning-lights-remains-steady.html

------------

Can I drive the car without ABS fuse connected?

http://schematicsdiagram.blogspot.in/2012/02/can-i-drive-car-without-abs-fuse.html

-----------

Where is ABS/TCS module located on 2005 Cadillac Deville

http://schematicsdiagram.blogspot.com/2011/12/where-is-abstcs-module-located-on-2005.html

------------------

ABS motor keeps running?

http://schematicsdiagram.blogspot.com/2012/01/abs-motor-keeps-running.html

------------

When the car stops, abs pump turns ON?

http://howtobyme.blogspot.com/2011/12/when-car-stopsabs-pump-turns-on.html

-----------

Replacing ABS unit on Buick Century?

http://technoanswers.blogspot.in/2012/02/replacing-abs-unit-on-buick-century.html

----------------

2008 Toyota Tacoma: ABS causes Brake pedal fade?

http://technoanswers.blogspot.in/2012/04/2008-toyota-tacoma-abs-causes-brake.html

--------------

Toyota Camry: Premature ABS Actuation?

http://technoanswers.blogspot.in/2012/04/toyota-camry-premature-abs-actuation.html

-----------

How to replace ABS Modulator Control Unit on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-replace-abs-modulator-control.html

----------------


How to replace ABS Pump Assembly on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-replace-abs-pump-assembly-on.html

-----------


How to remove ABS Accumulator on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-remove-abs-accumulator-on-acura.html

---------


How to remove ABS Control Unit on Acura Integra?

http://repairhelpcenter.blogspot.in/2011/11/how-to-remove-abs-control-unit-on-acura.html

------------

These details will help.

Thanks.

Feb 04, 2013 | Cars & Trucks

1 Answer

ABS light stays on - can you unsolder relay in ECM with common iron.


ABS light on did they check codes ? The light staying on an no codes is usually a insturment cluster problem not the EBCM - electronic brake control module . No relay in side the module , a transistor or diver as they call them . This transistor will supply a ground on a electrical circuit from the brake lamp driver module ,when it does this the brake lamp driver module ground a electrical circuit for the ABS light . If anything is bad causing the ABS light to stay on it would be the brake lamp driver module . Your best bet ,take it to a GM service dept.

Aug 05, 2017 | 1999 Pontiac Bonneville

2 Answers

Abs light stays on and a yellow triangle warnng light


On occasion an ABS light will come on when a brake light is out. So check your brake lights first. Your ABS light is on because there is a malfunction in the ABS system. Is your brake warning light and your ABS warning light both on? This would be an indicator of a major malfunction in the ABS system. Stop driving the vehicle and fix this immemorially. If only your ABS light warning light is on this will not effect normal braking but the ABS system is disabled while the ABS warning light is on. You still need to have it repaired but you still have brakes for the moment. Now the code for this fault will be stored inside the ABS memory module. So you pinpoint this with scanner. Hope this helps

Mar 22, 2011 | Volkswagen New Passat Cars & Trucks

1 Answer

What causes anti lock brake fuse light to stay on?


ANTI LOCK BRAKE LIGHT.MEANS ANTI LOCK BRAKES NOT WORKING.CHECK ABS FUSE AND RELAY.IF ALL IS GOOD.HAVE THE ABS BRAKE SYSTEM CODE SCAN.NOT SAFE TO KEEP DRIVING.HAVE FIX QUICK AS POSSIBLE.BECAUSE THE ABS BRAKE UNIT IS PART OF YOUR MAIN BRAKING SYSTEM.IF ABS BRAKE UNIT BAD BY BEING PART OF THE MASTERCYLINDER IT CAN CAUSE COMPLETE BRAKE FAILURE.

Oct 02, 2010 | 1996 Ford Taurus

1 Answer

ABS and ASC warning lights stay on 2000 530d


Check to see if your brake pads and rotors are in good condition. Or if you have replaced the pads yourself and have not reset the wheel sensors this would cause the ABS Antilock Brake System light and the ASC Automatic Stability Control light to stay on as the ASC uses the ABS brakes with computer assistance to control the car

Jul 06, 2009 | 1999 BMW 5 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...