Question about 2005 Hyundai Tucson

Open Question

Looking for fuse for reverse lights in my ix35

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2012 Hyundai ix35& have fitted a towbar wiring loom.


take it to an accredited auto electrician to have the reverse sensor disconnected when the trailer is connected as the sensors are seeing the trailer when reversing and that is why they are beeping

Feb 17, 2016 | Hyundai Cars & Trucks

1 Answer

My IX35 ABS light is on


You will need to get it scanned for ABS codes. Could be defective wheel speed sensor.

May 23, 2015 | 2011 Hyundai ix35 2.0

1 Answer

Set clock ix35


DOES THE DISPLAY LIGHT ON? NO....CHANGE THE CLOCK FUSE.

Mar 22, 2014 | 2014 Hyundai Tucson

1 Answer

Fuse location reverse lights


hi. its usually on the lighting fuse but if your other lights are fine
then i would be looking at changing the reversing switch located
around. and near the gear leaver. good luck

Jan 27, 2014 | Toyota Cars & Trucks

1 Answer

My tail lights/reverse lights are not working - either side. checked the fuses, they seem fine. the brake light above the tire does work? any suggestions - going to see my Dad Sunday (old mechanic),...



reverse is a whole different circuit. via the transmission reverse switch..
my guess is you have burned out lamps.
im looking at alldata.com now. (so can you)
and i will pick the Reverse page, its boy scout simple
battery, fuse 39, wires a switch and 2 lamps.

i bet fuse 39 is blow,
replace, it. some that look good, are in fact not (micro cracks)
or use an ohm meter (dmm set to ohm low)
0 ohms good
infinity bad.

there is a fuse box in engine bay and cab.




Dec 12, 2013 | 2008 Jeep Wrangler Rubicon

1 Answer

Faulty fuel gauge hyundai ix35


Usually a problem with the sending unit in the tank.
The car is under factory warranty, right ?

Jul 15, 2012 | 2011 Hyundai ix35 2.0

1 Answer

Reverse light fuse blows when put into reverse


Unfortunately, many possibilities. If you have time, start by removing both reverse lamp sockets from light assembly(and keep from touching any metal), remove bulbs from sockets, CAREFULLY INSPECT sockets and wires. New fuse of correct rating. Turn key on and try again in reverse.
Fuse still blows: Next place to look is transmission reverse electrical switch and wiring as far as you can trace looking for burned/stripped wires near transmission and wires by sockets
Fuse doesn't blow: Turn key off and install one lamp in socket at a time. DO NOT install sockets into fixture at this time. Test. Remove first lamp to check second. If still O.K., each socket back into fixture(one at a time same as before)and test. Most common problems: Sockets contaminated, wires shorting at sockets, bulbs installed incorrectly shorting to ground.

Sep 25, 2009 | 1996 Ford Explorer

1 Answer

When I shift to Reverse my reverse lights wont work.


There is a switch on the steering colum that works the backup lights

Dec 06, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
2005 Hyundai Tucson Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...