Question about Hyundai Excel

Open Question

Dohc timing belt

How do I replace the timing belt on A Hyundai Getz 2007 DOHC model?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22095 Answers

SOURCE: timing belt diagram for 2001 ford escort zx2 dohc

cam shaft timing marks on back of cams ,two slots ,use a flat piece of metal to align .remove no1 spark plug and drop long thin screwdriver down it to bring piston just below tdc,then align cams so both cams are on the rock (valves closed) with knob on back cam aligning with pick up sensor left side between lobes.then bring piston up to tdc and fit belt.turn engine over twice with socket on bottom pulley to make sure no valves clear pistons.Remember to remove flat edge from back of cams i didnt last time and bent my home made tool

Posted on Jan 28, 2009

  • 5 Answers

SOURCE: 1997 saturn sl2 dohc is there a timing belt or chain on it

These engines have a timing chain, not a belt. They also have nylon coated guides under the cover that wear. If you change the chain yourself, or have it done, check the guides as well.

Posted on Mar 26, 2009

c17hydro
  • 2984 Answers

SOURCE: timing belt replacement

ad8bce3.gif
Hope this helps!!!!

Posted on Jun 19, 2009

  • 21 Answers

SOURCE: Focus timing belt replacement.

This is a very very easy timing belt setup. first off you have to remove the valve cover. Then you have to remove the serp belt. Then remove anything thats in your way of the front cover. after you remove the crank pulley re-install the crank bolt. DO NOT LOSEN THE BOLT FOR THE TENSIONER!!!! now spin the crankshaft until the sproket aligns with the timing mark. now at this point the two camshafts should be aligned. now there is a special tool from ford that holds the cam shafts in place. all it is is a 1/4" peice of metal that goes on the left side of the cam shafts to hold them into place. if you mark the cams you wont need the tool. or if you can find something to fit in the left side of the cams that will work too. anyways after that its just the same steps in reverse. very easy to do.

Posted on Aug 31, 2009

  • 1757 Answers

SOURCE: I need diagrams on timing belt replacement on a 94

Click on the following Link. It has all the Diagrams for the Timing Belt.
Before Clicking, let me know if this helped you.

http://www.2carpros.com/car_repair_information/year/1994/make/ford/model/probe/1994_ford_probe_timing_belt_diagram_marks.htm

Posted on Feb 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve engine


Choose:

1994 Mazda MPV timing belt replacement, 6 cylinder DOHC ...

? 3:46
https://www.youtube.com/watch?v=sD2G-NzycvU
Aug 11, 2011 - Uploaded by rsarp
1994 Mazda MPV timing belt replacement, 6 cylinder DOHC 3.0... engine so the valves would not be bent ...

How to replace the timing belt on a 1994 mazda 929 3.0 ...

www.fixya.com/.../t25991928-replace_timing_belt_1994_mazda_929_3...
4 hours ago - how to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve... I have a 2000 Mazda 626 4cyl 2.0 liter DOHC engine replacing the timing belt, what ... 2004 6s, 3l. where is the canister purge valve solenoid located?

Where are the timing marks on a 1994 mazda 929 3.0l - Fixya

www.fixya.com/cars/t25991952-timing_marks_1994_mazda_929_3_0l
4 hours ago - where are the timing marks on a 1994 mazda 929 3.0l - Mazda Cars ...1994 Mazda E2000 Cam Timing Mark Positions to Replace Timing Belt ... on a 1994mazda v6 dohc 24 valve engine How to align the timing mark on the ...

Mazda Timing Belt Replacement



Dec 03, 2015 | Mazda Cars & Trucks

2 Answers

How replace timig chain in accent dohc


should be 1.6L engine. easy to replace but is a belt not chain. unless you know how to line up camshaft / crankshaft, I'd pay for the labor. full kit on RockAuto.com is about $50

remove front right wheel, unbolt engine mount top passenger side, loosen accessory pump at top, remove timing belt covers (upper & lower), replace belt and idlers from kit.
to reassemble....reverse steps.
yes, it is that simple BUT not for a neophyte. inspect original belt before replacement, if no cracks, I'd leave alone. mine had 145,000 at replacement and was still good.

Jan 03, 2013 | 2007 Hyundai Accent GS Hatchback

1 Answer

Does one have to change the timing belt of a Hyundai tuscon 2006 model. I


Scheduled Maintenance Services, for most Cars, has to be done at 30K, 60K, and 90K. Hyundai dealer recommend to replace the timing belt at 60K Service.
If you wait, one of two things could happen: Nothing, or the belt could break and you would be out thousands to repair the engine instead of a $400 hundred to replace just the belt. If it breaks, there will be damage done to the valves and various other internal components, which will not covered under warranty. The problem is that the Dealer would charge you between $700-$800 because they would also replace the water pump at the same time. Or you can buy the timing belt and change it by your self. To do so, you nee the Haynes Repair Manual specific for your car another equivalent.
2006 HYUNDAI TUCSON GLS 2.7L 2656cc V6 FI (D) DOHC : Engine : Timing Belt

9faaa22.jpg

Oct 29, 2010 | Hyundai Tucson Cars & Trucks

1 Answer

I need to know how to replace a water pump on a 2002 hyundai gx 350.


2002 Hyundai XG350 3.5L MFI DOHC 6cylWater Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Accessory drive belts Water pump pulley Timing belt, tensioner and idler pulley Water pump

  4. 1514f36.jpg

    Fig. Water pump assembly-XG 300 and XG 350 (click over pic for zoom)

To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.
To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.

95486b3.jpg


Fig. Water pump bolt lengths-3.5L engine

Install the water pump with new gaskets and O-rings. Tighten the bolts to the following specifications:
  1. 1.5L SOHC engine: 105-132 inch lbs. (12-15 Nm).
  2. 1.5L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  3. 1.6L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  4. 1.8L, 2.0L, and 2.4L engines: 14-20 ft. lbs. (20-27 Nm).
  5. 2.5L engine: 11-16 ft. lbs. (15-22 Nm).

Hope helps (remember rated this).

Jun 18, 2010 | 2002 Hyundai XG350

1 Answer

Diagram for serpentine belt


For the 2004 Hyundai Santa Fe:
I do not know if you have the 2.4L DOHC In-Line 4-Cylinder, 2.7L DOHC V6, or the 3.5L DOHC V6 Engine; however the Link below has all three Diagrams.

Click on the following: direct, free Link. It has the Belt Diagrams for your 2004 Hyundai Santa Fe. It also has very helpful Instructions and Directional Diagrams.

Let me know if this helped...
http://www.2carpros.com/car_repair_information/year/2004/make/hyundai/model/santa_fe/2004_hyundai_santa_fe_drive_belt_routing_diagram.htm

Apr 23, 2010 | 2004 Hyundai Santa Fe

2 Answers

Need the timing marks for 2001 hyundai tiburon


1.5L And 1.6L Engines

a826891.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


4e7384e.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines



1.5L Engines

238c1f1.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


b1c71ee.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines


c200f83.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines, 1.6L similar



1.8L (VIN M) And 2.0L (VIN F) Engines

656db91.jpg

Fig. Proper alignment of the timing belt alignment marks for belt removal and installation-Hyundai 1.8L and 2.0L (VIN F) engines



2.0L (VIN P) Engines

7208166.jpg

Fig. Oil pump and crankshaft inner timing belt sprocket alignment marks-Hyundai 2.0L (VIN P) engines


7080ea8.jpg

Fig. Timing belt sprocket alignment mark locations and positioning for belt removal and installation-Hyundai 2.0L (VIN P) engines



3.0L (VIN G)

3b377fb.jpg

Fig. Installation of the timing belt-3.0L (VIN G) engine




7b32092.jpg


Fig. Timing belt sprocket alignment mark positioning for belt removal and installation-Hyundai 3.0L engine


Hope this helped (remember comment and rated this post).

Apr 13, 2010 | 2001 Hyundai Tiburon

1 Answer

Diagrams on How to Replace the Missing Belts on a 2000 Hyundai Accent


Click on the following direct Link. It has the Belt and Instruction Diagrams for your specific 1.5L engine (SOHC/DOHC) options (AC/No AC, etc.).

Let me know if this helped....
http://www.2carpros.com/car_repair_information/year/2000/make/hyundai/model/accent/2000_hyundai_accent_drive_belt_routing_diagram.htm

Mar 26, 2010 | 2000 Hyundai Accent

2 Answers

TIMING CHAIN CHANGE


hyundai recommends replacing the belt every 60,000 miles or 48 mos and this is an "interference" engine which means if the belt breaks, it will cause internal engine damage. happy holidays

Dec 28, 2009 | 2001 Hyundai Accent

1 Answer

2007 Hyundai Santa Fe AC Fiter


Fuel pump (INCLUDING FUEL FILTER AND FUEL PRESSURE REGULATOR) item No2 on next Fig.
dd110b4.gif G 3.3 V6 DOHC and G 2.7 Vs DOHC Fuel System
b2ee82a.gif

Jun 24, 2008 | 2007 Hyundai Santa Fe Limited

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

145 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...