Question about Cars & Trucks

Open Question

Remove engine cover golf mk5 1.6fsi - Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Engine cover

I am assuming this is a diesel. The diesel engine covers were extremely hard to remove. They are held on by rubber grommets and these grommets tend to dry out and then get stuck. I have broken many of these covers. VW is aware this is an issue, but does not want to do anything to fix it

Feb 11, 2014 | 2010 Volkswagen Golf

1 Answer

Removing engine cover 2010 vw golf

Hi. pull from the rear lhs corner first. it sits tight. careful not to break it.

Feb 11, 2014 | 2010 Volkswagen Golf

2 Answers

I have a golf 2003 bcb how can i remove the engine cover there does not seem to be any screws to undo

Hi Ithink you will find the engine cover on the golfs has no screws as you`ve said.the cover is fixed in possition by 3 or 4 plastic moulded balls on the under side of the cover.These balls fit into rubber gromets, So the cover will just lift off with a steady pull, sometines there are clips holding some pipes to the cover.
Hope i have been of help to you
John (South Wales UK )

Apr 24, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

How to replace timing belt 1995 vw golf

  1. remove air intake pipe, and box (upper and lower section)
  2. take off timing belt cover
  3. take off serpintine belt, and v belt
  4. rotate engine to TDC marks line up on crank and cam. camshaft says O^T on it and on the cover behind gear, crank has a notch in the pulley and a arrow on the cover to line up
  5. remove crank pulley 6mm allens not the 19mm 12 bolt
  6. make sure timing belt is still at TDC remove lower timing belt cover there is 3 bolts and a nut holding it on the nut is by the water pump and the bolts are on on top and 2 behind the crank pulley
  7. remove cover
  8. mark intermediate shaft shaft right above the crank pulley
  9. remove belt
  10. install reverse of removal make sure to line up all 3 pulleys cam crank and intermediate shaft or it wont run and depending on how bad it is out of time if you do it wrong you could bend valves
Assuming this is a 2.0 8v your question is pretty vague

Feb 23, 2010 | 1995 Volkswagen Golf

1 Answer

Oil change and cam belt/timing chain change for volkswagen golf 1.9cc tdi 130 bhp, 1992 model

support engine. remove coolant reservoir. remove serpentine belt. remove serpentine belt tensioner. remove bolts from mount. carefully raise engine up and move mount out of the way.(hard to explain and this is hard to do you have to have the engine in the perfect position and whatnot) remove the top plastic cover. with 19mm socket rotate engine clockwise until hole in cam lines up with hole in head. insert vw special tool to hold cam. remove the 4 6mm bolts on crank pulley. remove plastic covers. with white paint, mark belt to cam and belt to crank. loosen tensioner. remove belt. transfer marks to new belt. strongly suggest replacing water pump. reinstall t-belt. put the tensioner somewhat tight. rotate the engine fully twice. loosen tensioner bolt and adjust to perfect tension using needle and v-groove on adjuster. install is reverse of removal.

Jan 31, 2010 | 2001 Volkswagen Golf

1 Answer

Where is the thermostat on my 05 golf tdi

drain collant, remove wather cooler lower hose from the engine block.(plastic cover is also thermostat cover)

Jan 02, 2010 | 2005 Volkswagen Golf

1 Answer

Where is the fuel filter located

2.0L 4 cylinder
2.8L 6 cylinder
Right side passenger door underneath the car.
you will find the fuel filter it is cover with a cover,
remove the cover and the fuel filter is there.

1.9L DSL Turbo
Engine compartment,passenger side, near the coolant tank.

Let me know

Sep 26, 2009 | 1998 Volkswagen Golf

1 Answer

Mk4 golf 1.6 16v misfire

i had that with my mk3 golf..and i done everything i could then finally i changed the ecu relay fuse. that solved it completely. they are cheap to buy from £15ish. hope this helps

May 04, 2009 | 2001 Volkswagen Golf

1 Answer

Water pump change , removing belt gear covering pump

you have to remove the right side tire this will give you access to the pump through the wheel well

Sep 04, 2008 | 1994 Volkswagen Golf

2 Answers

Cam shaft position sensor

let me have engine code then i can tell you

Jul 08, 2008 | 1998 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides