Question about Hyundai Motor 2002 Sonata
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: location of Charcol Canister and
The evaporative emission canister purge solenoid valve is a duty control type, which controls the flow of purge air from the evaporative emission canister.
Inspection 1. Look for loose connections, sharp bends or damage to the fuel vapor lines. 2. Look for distortion, cracks or fuel leakage. 3. After removing the EVAP canister, inspect for cracks or damage.
Posted on Sep 04, 2008
Posted on Apr 23, 2009
Hello onarock844...The Hyundai 2.4 litre and the 3.3 litre are known to have valve train noise. Some sooner than others.
The timing chain tensioners on the 06 and 07 Sonata 3.3 engines built before August 4, 2006 are well known for developing wear that allows them to make a tapping or rattling noise for a short time after a cold start. This noise can be mistaken for a lifter noise, although the actual source is in the front cover area of the engine. Hyundai has released a technical service bulletin on this problem, which describes installation of an updated design timing chain tensioner (part #24410-3C300) to correct this noise issue.
Ask your dealer to refer to Hyundai service bulletin #06-20-002 for information...If this has already been corrected,,,and the noise is coming from the upper engine area and not from the timing chain area, then the valve clearance will need to be adjusted. This is done by disassembling the valve train and installing slightly different size tappets to change clearance.
This is a fairly labor intensive process, so if you are still under factory warranty then you will want to go over the dealer's head and get the Hyundai zone rep involved to get it covered before your warranty coverage expires...
I recommend useing a full synthetic engine oil, i know in a few cases where the noise has stopped when the oil was changed over to synthenic, also a high quality filter is important, such as a purolator.
Good luck...i hope this helps...please rate me a fixya.
Posted on Jul 29, 2009
The adjustment screws/nuts should be located either on the top of the headlamp assembly,
behind the headlamp assembly, or near the frame rail by the radiator
You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well
Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)
If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.
Posted on Sep 30, 2009
Tips for a great answer:
Nov 04, 2016 | 2002 Hyundai - Sonata
Feb 10, 2016 | Hyundai Cars & Trucks
Dec 25, 2013 | Hyundai Motor 2002 Sonata
Oct 04, 2011 | Hyundai Motor 2002 Sonata
Dec 18, 2010 | Hyundai Motor 2002 Sonata
Oct 15, 2010 | 1999 Hyundai Sonata
Feb 02, 2010 | Hyundai Motor 2002 Sonata
Dec 11, 2009 | Hyundai Motor 2002 Sonata
Mar 23, 2009 | 2005 Hyundai Sonata
52 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: