Question about 1997 Mazda Protege

Open Question

Clutch plate moving the transmission to install clutch plate. There seems to be more bolts than expected. I need a diagram or instructions.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace a clutch in a 1998-99 Geo metro


why not post symptoms first, (like, my clutch pedal is dead) or?
manual or automatic trans/ both have clutches.?????
metro ended in 97 and was then and a Chevrolet nameplate from 1998 to 2001
metro, is covered in all metro, FSM books
all metro forums
see vast links here
http://www.fixkick.com/swift.html

online:
and at alldata.com
mitchels.
dont know year, ?

my wild guess. on what is there, M/T stick shift car.

M/T stick
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Transmission assembly and matchmark the flywheel to the engine
    • Clutch pressure plate cover by slowly and evenly loosening the bolts until the spring tension is released
    • Clutch disc

Trans out,
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the transmission fluid.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Both front wheels
    • Backup lamp switch electrical connector
    • Clutch release lever from the clutch release shaft
    • Clutch cable bracket and move it aside
    • Negative battery cable and hanger from the transmission
    • Gearshift guide case bolts and set the engine wire harness and bracket aside
    • Speedometer cable
    • Starter motor
    • Two right side upper case-to-engine bolts
  4. Install an engine support fixture.
    • Both drive axles after properly supporting the transmission
    • Flywheel cover
    • Control joint shaft through bolt and separate the control shaft from the control joint
    • Gearshift control lever guide plate and separate the extension rod from the lever guide plate
  5. Support the transmission.
    • Bolts from the rear transmission mount
    • Left side mounting bracket bolts
    • Right side case-to-engine mounting bolts
    • Transmission through the left side of the engine compartment and make certain that the input shaft clears the clutch pressure plate

Feb 14, 2015 | Geo Cars & Trucks

1 Answer

How to replace a flywheel on a ford five hundred


Remove the inspection plate and undo the bolts attaching the torque converter to the flex plate Remove transmission If you are not familiar with that procedure give the job to a mechanic. Remove the clutch if not auto again know how to replace clutch pressure plate and clutch plate. Something tells me that the flywheel isn't stripped but the flexiplate has fractured as it is unusual for the teeth of the ring gear to be completely stripped. Moving on use an impact gun to undo the bolts holding on the flywheel/flex plate Installation is reverse to removal. But I recommend you have good advice handy to do this job

PLEASE RATE THIS REPLY FOR ACCURACY

Mar 23, 2013 | 2007 Ford Five Hundred Limited Sedan

1 Answer

How to install a clutch kit on my 1994 mitsubishi mighty max


Disconnect the battery, disconnect the Hydraulic Line from the Slave Cylinder, Remove the Starter (2 bolts, 2 wires. Bolts are 14mm, 1 wire is 12mm, 1 plugs in), Remove the Driveshaft(s) (4 12mm bolts) Remove the 6 bolts from the bellhousing (4 are 14mm, 2 are 10mm)
Remove the bolt from the Transfer Case Mount, 12mm (only if it's a 4WD, if it's 2WD this doesn't apply), remove the 2 bolts that hold the Transmission Mount to the Crossmember (12mm or 14mm, it varies)
Slide the transmission back on the crossmember, away from the engine, I recommend running a ratchet strap across the frame to balance the transmission.
Remove the Pressure Plate from the Flywheel (Six 10mm bolts), Inspect the Pilot Bearing (if it needs replaced, you'll need to remove the Flywheel which is held on with six 18mm bolts, drive out the old bearing and drive in the new one, reinstall the flywheel, using Threadlocker on the bolts, torque the bolts to 100 ft lbs) Install the new clutch disc and Pressure Plate, with the centering tool inserted through the disc into the pilot bearing. Use thread locker on the pressure plate bolts and torque them to 20 ft lbs. Remove the centering/alignment tool after you've bolted it together
Remove old Throw Out bearing from input shaft on the transmission and slide the new one on. Slide the Transmission forward (make sure the input shaft slides into the pilot bearing, don't force the transmission into place or you could damage the clutch disc or break the input shaft) Torque the Bellhousing Bolts to 40 ft lbs (4 14mm bolts), Torque the 2 10mm bolts to 14 ft lbs, Install the Starter (torque bolts to 23 ft lbs), Reconnect Hydraulic Line to Slave Cylinder. Torque Transmission Mount Bolts to 30 ft lbs.
Reinstall Driveshafts, torque bolts on flange/yoke to 40 ft lbs. Fill Clutch Master Cylinder with DOT-3 Brake & Clutch Fluid, Open Bleeder Screw on Slave Cylinder and bleed the air out of the system, close bleeder screw.
Reconnect the wires to the Starter, Reconnect the battery.

Aug 24, 2011 | Mitsubishi Mighty Max Cars & Trucks

1 Answer

Need a copy of the manual pages, showing how to replace the clutch


Removal & Installation To Remove:
  1. Remove the transmission.
  2. Install a flywheel locking tool.
  3. Remove the pressure plate mounting bolts from the flywheel.
  4. Remove the pressure plate and clutch disc.
To Install:
  1. Insert a clutch disc alignment tool through the disc splines and into the flywheel pilot bearing. Pressure plate balance mark location subaru-07-00-6722.gif

  2. Install the pressure plate on the flywheel with a gap of 120° or more between the "0" balance marks on the flywheel and pressure plate. Hand tighten the pressure plate mounting bolts.
  3. Tighten the pressure plate mounting bolts using a crisscross pattern 12 ft-lb (16 Nm).
  4. Remove the clutch disc alignment tool.
  5. Install the transmission.
prev.gif next.gif

Dec 28, 2010 | 1998 Subaru Legacy

1 Answer

How to replace the clutch on front wheel drive cars


It is best to replace the clutch driven plate, pressure plate and release bearing at the same time.
You have to remove either the transmission or the engine(or both). On some vehicles it is not possible to remove the engine without the transmission. I prefer removing the transmission only, since it does not require a hoist. (Removing engine and transmission complete is a bit more complicated,theres much more things to disconnect, but makes things easier when mating the transmission to the engine after replacing the clutch assembly). When removing the transmission only make sure the engine is properly supported, since the engine is supported by the transmission and vise versa.
Take note of all pipes and cables that you remove and mark them with masking tape since that gives you something to write a description on. Remember to mark the spot that you disconnect from as well. Taking close-up pictures of the engine bay will work wonders when your memory fails.
Read through this : http://www.fixya.com/cars/t4984410-remove_front_axle_get_engine (solution 2)
Drain transmission oil. Remove the driveshafts as described. Remove any electrical connections to the gearbox.
Remove the gearshift linkage. Remove the clutch cable/clutch operating mechanism(hydraulic clutch) Remember to support the engine before unbolting the transmission from the engine. Remove any mountings still connecting the transmission to the body of the car..
Remove the transmission from the engine bay. It is possible to do this by hand (a helper would be a plus at this point)
The clutch pressure plate is then visible on the engine and held in place by 6 bolts. It can be removed along with the clutch plate(which will drop free once the pressure plate is removed. Replacing the clutch is pretty straightforward, except that the clutch plate needs to be centered, or the transmission wont go back on. Autozone stocks a clutch centering tool which you can purchase although some clutch kits come with the centering tool supplied, else you can fashion one out of a wooden dowel. The dowel needs to fit snugly into the recess in the centre of the flywheel. Use insulation tape to build it up if it is too thin. The clutch plate can go in one way only. You will note that the clutch plate centre has a metal plate fitted on one side. This is the transmission side of the plate. Fit the clutch plate and pressure plate to the flywheel and tighten the bolts just enough to hold the clutch plate in place so that it doesnt move around. Using your centering tool make sure the clutch plate is nicely centered. Then tighten the bolts to the specified torque. Which means tighten them up without breaking them. Get the transmission fitted to the engine. This may take some doing especially if the clutch centering didnt go too well. Now reconnect everything and drive the vehicle to the nearest alignment centre to re-set the wheel alignment.

Jul 07, 2010 | Cars & Trucks

1 Answer

How to replace a clutch in a 95 nissan pickup


hELLO remove your transmission from your truck and unplug all lines and electric wire from it and you will see your pusher plate removed all bolts on the pusher plate and remove the plate and the clutch disc also remove the flywell from the engine and get it refaced from the brake shop and also install a new clutch bearing at the same time,you will have to center your clutch disc when you will install the clutch the way to do it is you put the disc and the pusher plate togeter you install the bolt on the pusher plate snog by hand but dont tight it at this time put the centering toll trought the hole in pusher plate and the disc and center the disc and tight the bolts on the pusher plate at this time and remove the toll(if you remove the flywell those bolts have a torque on it be sure to torque the bolts at the right torque for it refer to a mecanic for it and reinstal your transmission.

Mar 08, 2010 | 1995 Nissan Pickup

1 Answer

Info on do it tyour self clutch removal on 2001 mustang 3.8


REMOVAL:
  1. Lift clutch pedal to uppermost position to disengage clutch and brake pedal pivot shaft.
  2. Push clutch and brake pedal pivot shaft forward and unhook clutch release lever cable from clutch and brake pedal pivot shaft and allow it to slowly swing rearward.
  3. Raise and support vehicle.
  4. Remove clutch release lever dust shield.
  5. Disconnect clutch release lever cable from clutch release shaft.
  6. Remove retaining clip, then clutch release lever cable from flywheel housing.
  7. Remove starter motor from flywheel housing, then engine rear plate to front lower flywheel housing bolts.
  8. Remove transmission.
  9. Remove flywheel housing back just far enough to clear clutch pressure plate, then remove housing.
  10. Remove clutch release shaft from flywheel housing by pulling it through window in flywheel housing until retainer spring disengages from pivot.
  11. Remove clutch release hub and bearing from clutch release shaft.
  12. Loosen six clutch pressure plate bolts evenly to release spring tension gradually and avoid distorting clutch pressure plate. If same clutch pressure plate is to be installed, mark plate and flywheel so pressure plate can be installed in its original position.
  13. Remove clutch pressure plate and clutch disc from flywheel.
INSTALLATION:
  1. Position clutch disc and pressure plate assembly on flywheel, noting following:
    1. Three flywheel housing to block dowels on flywheel must be properly aligned with clutch pressure plate.
    2. Bent, damaged or missing flywheel housing to block dowels must be replaced.
    3. tart clutch pressure plate bolts but do not tighten.
    4. Avoid touching clutch disc face, dropping parts or contaminating parts with oil or grease.
    5. Align clutch disc using suitable alignment tool inserted in pilot bearing.
    6. To avoid clutch pressure plate distortion, alternately tighten bolts a few turns at a time, until they are all tight, then tighten to specifications.

  2. Install transmission to flywheel housing.
  3. Install engine rear plate to flywheel front lower housing bolts, then connect clutch release cable to flywheel housing and connect retaining clip.
  4. Connect clutch release lever cable to clutch release shaft, then install clutch release lever dust shield.
  5. Install starter motor.
  6. Lower vehicle, then install clutch release lever cable as follows:
    1. Lift clutch pedal to disengage clutch and brake pedal pivot shaft.
    2. Push clutch and brake pedal pivot shaft forward and hook end of clutch release lever cable over rear of clutch and brake pedal pivot shaft.

  7. Cycle clutch pedal several times to adjust clutch release lever cable

Aug 08, 2009 | 2001 Ford Mustang

1 Answer

Change transmission instructions


this is for rear wheel drive only front wheel drives require removing axle shat and dropping tie rod end and lower ball joint to get tranny out. If you start this I will give tork setting when I know what you have as it is a lot of work to type this out.

First disconnect the battery, inside the cab pull shifter boot off and remove snap ring to remove shifter, next get a block to go under engine remove drive line bolts and be sure E-brake is set and block the wheels, next put bolts from driveline into the read differential in order so you will be able to find them next disconnect the two starter bolts from the starter and tie starter up as not to allow the starter weight to hang on the wires. Remove two bolts holding slave cylinder on let hang off the side do not lose the shaft out of slave. Next remove the transmission mount bolt out next pull four bolts out of transmission cross member, next remove 5 bolts out of bell housing now get a baggie and a couple of rubber bands and pull drive shaft slide baggie over the transmission tail shaft and put on rubber band on bag to keep from losing fluid move drive shaft out of the way. Next disconnect the Speedo cable and wiring harness the reverse switch is at the top so will have to drop the tranny down to keep from breaking wire. Once you have a gap between the transmission and engine put block under back of engine slide the transmission out let the front drop down then lift up on rear of transmission and slide the cross member out of the way. Next slide tranny out of the way next remove the 6 bolts on the clutch assembly turning each bolt 1 and a ½ turns each till clutch is loose remove the clutch pressure plate and the throw out bearing, remove flywheel take to machine shop and have surfaced, replace the clutch plate pressure plate and the throw out bearing reinstall in reverse if you see any oil leaks replace seals, also replace rear transmission seal now if you don’t it will leak next after it is back together be sure you put new fluid in the transmission and bleed the slave cylinder.

Jun 28, 2009 | Nissan Pickup Cars & Trucks

1 Answer

Need help fitting a clutch on a VW GTI Golf


undo centre wheel hub nut 30mm/32mm, socket. undo lower wish-bone outer bolts, disconect battery,/remove starter motor,/remove transmission mounting bolts to body frame ,/ remove all surrounding bolts around bell housing transmission,/ remove clutch cable from transmission,/ remove drive shafts from centre hub and transmission,/ make sure car is standing on axle stands at front of jacking points,/use a trolley jack to suport engine sump with a piece of wood,/ slide transmission away from flywheel,/lower transmision on floor,/undo all clutch plate preasure bolts 10mm,/remove thrust bearing located on centre transmision shaft ,.also make sure if fitted speedo cable needs to be removed.new clutch plate should indicate flywheel ,without fitting clutch plate wrong way round/otherwise transmision will not bolt to engine block.,

May 17, 2009 | 1999 Volkswagen GTI

1 Answer

Line up of trans to motor doing clutch replacement 88 dodge ram


Leave your clutch assembly bolts loose, so the clutch plate can move as needed to line it up, then tighten them after tranny fully in place. I believe most autoparts store now will lend or rent you an alignment tool if necessary. I guess I was lucky, I always seemed to find something I could use to align it by eye.

Nov 16, 2008 | 1988 Dodge Ram 50

Not finding what you are looking for?
1997 Mazda Protege Logo

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...