Question about 2001 Chrysler Town & Country

Open Question

2006 chrysler town and country Purge Valve location

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

garyq1970
  • 73 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

emissionwiz
  • 75744 Answers

SOURCE: where is the body control module located on a 1997 town & country

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket

Posted on Mar 23, 2009

c17hydro
  • 2984 Answers

SOURCE: Front PCV Valve on chrysler town and country

1930013.gif
PCV valve location-2.4L engine

3a8cecf.gif
PCV valve location-3.3L and 3.8L engines

Posted on Nov 13, 2009

  • 1 Answer

SOURCE: code EGR P404

Or before shelling out that kind of cash; you could try cleaning the seal on your gas cap and/or replacing your gas cap first. My '06 has tripped this code twice (after very dry or very cold weather).

Posted on Dec 29, 2009

ZJLimited
  • 17970 Answers

SOURCE: I need the diagram of the 2006 Chrysler Town &

For 2006 Chrysler Town & Country fuse diagram, check the Owners Manual (page 434 and next).

Hope this help (remember rated and comment this).

Posted on Mar 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Purge or vent solenoid where is it for eval system


Purge solenoid is located on the front rad support on the left of vehicle when looking at vehicle from the front. It has one electrical connector and 2 hoses attatched

Dec 27, 2013 | 2006 Chrysler Town & Country

1 Answer

Does anybody have a diagram for where the purge valve is located on a 2003 town and country


Look on the passenger side of the engine near the radiator. It will have a single two wire connector and two vacuum hoses joined by a single rubber connector attached to it.

Sep 03, 2012 | 2003 Chrysler Town & Country

1 Answer

Code p0443 town & country


code is for fume purge control
To cause a P0443, there has to be a problem with the purge control CIRCUIT, not necessarily the valve. Usually they are a unit housing the valve and the solenoid as an assembly. Or it could be comprised of a separate solenoid with vacuum lines to a purge valve. That said, it could be any of the following:
  • Bad purge solenoid (internal short or open)
  • Wiring harness chafing or rubbing another component causing short or open on control circuit
  • Connector worn, broken or shorted due to water intrusion
  • Driver circuit inside powertrain control module (PCM) is bad

Jun 09, 2012 | 2006 Chrysler Town & Country

2 Answers

I have a 2004 Chrysler Town and Country and my


P0440:
  • Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
  • Inspect the EVAP system for cuts/holes in tubes/hoses
  • Inspect for damaged or disconnected hoses around the Evap purge solenoid
  • Check and/or replace the sensor
  • Check and/or replace the purge valve
  • Have a professional use a smoke machine to detect leaks

  • P0441:
    Bad vacuum switch
    • Broken or damaged EVAP line or canister
    • Open in PCM purge command circuit
    • Open or short in Voltage feed circuit to Purge Solenoid
    • Faulty purge solenoid
    • Restriction in EVAP solenoid, line or canister
    • Corrosion or resistance in purge connector
    • Bad PCM

    Dec 21, 2009 | 2004 Chrysler Town & Country

    1 Answer

    Front PCV Valve on chrysler town and country


    1930013.gif
    PCV valve location-2.4L engine

    3a8cecf.gif
    PCV valve location-3.3L and 3.8L engines

    Nov 13, 2009 | 1999 Chrysler Town & Country

    1 Answer

    Describe your 2002 Chrysler Town &


    On the driver side of the intake plenum close to the throotle body is were your pcv valve is located :)

    Aug 23, 2009 | 2002 Chrysler Town & Country

    1 Answer

    Describe your 2006 Chrysler Town & Country Problem p0404 engine code


    P0404 IS EGR POSITION SENSOR PERFORMANCE..YOU NEED A NEW EGR VALVE..RECOMMEND DISCONNECTING BATTERY WHILE REPLACING EGR VALVE..SOMETIMES CODE WILL NOT GO AWAY EVEN AFTER REPLACING VALVE AND CLEARING CODE WITH SCANNER..VALVE IS LOCATED ABOVE ALTERNATOR ON END OF CYLINDER HEAD..THE BOTTOM BOLT CAN BE TRICKY TO REMOVE AND HAVE HAD TO REMOVE ALTERNATOR TO GET BOLT OUT..YOU WILL NEED A NEW GASKET FOR TUBE AS WELL..ABOUT 120 BUCKS FROM DEALER(CAN)

    Jul 25, 2009 | 2006 Chrysler Town & Country

    1 Answer

    Code p0404


    replaced the EGR valve

    Jul 05, 2008 | 2006 Chrysler Town & Country

    Not finding what you are looking for?
    2001 Chrysler Town & Country Logo

    Related Topics:

    144 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    75744 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8123 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...