Question about Cars & Trucks

1 Answer

94 honda civic transmission

What does it mean when my car makes a grinding noise similar to when a throwout bearing goes out bad in the clutch but i replaced the entire clutch and throw out bearing twice now i think it may be a bearing in the tranny what do u think it could be ?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 190 Answers

If you have a lot of miles on the trans Might be time for a Bearing or 2.. Stick shifts are usually cheap to rebuild get a quote, And it's cheaper if you bring in the trans and not have them remove and install the trans I would say cost should be 125 to 175 to have it rebuilt

Posted on Oct 21, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Transmission noise in 2002 Mini Cooper 5 speed'

check the blogs out on the net. apperentely the mini coopers have transmission problems. My 2004 with less the 49,000 miles just went out. I thought it was a theow out bearing also. But I was wrong.

Posted on Aug 26, 2008

  • 31 Answers

SOURCE: 1999 Chevy Tracker Transmission Problem

Well it sounds like you have a the vacum for the four weel drive is trying to engage when it is in nutrial and that is where the noise is comeing from. I just think the person you took it to is just trying to make some money off of you

Posted on Oct 18, 2008

Mr BrokRench
  • 1623 Answers

SOURCE: 2003 Hyundai Tiburon making a weird noise

Hello mpolci...The 2003 Tiburon was sold to the public with a defective clutch, it failed due to warpage and bad pressure plate... among other things. There are MANY class action lawsuits. Did you resurface or replace the flywheel when the clutch was replaced? Did you go with an aftermarket clutch kit, or factory? Also the slave cylinder on the 03 was known to have a defective valve.
You can try checking the levels and bleeding the system and if you still have problems, then it could be a release bearing, a loose clutch pad, or a broken pressure plate spring....If the clutch is still under warranty, i would return it to the installer.
Good luck, i hope this helps...please rate me a fixya.

Posted on Aug 01, 2009

  • 83 Answers

SOURCE: Car makes a metalic grinding noise when in neutral

You need a new throwout bearing in your clutch assembly.

Posted on Sep 10, 2009

  • 72 Answers

SOURCE: rebuilding 1995 honda civic transmission

Did you make sure that the tork converter was all the way forward first if not then you will need to take the transmission back out and make sure that the converter has either automatic trany fluid in it or 184/85 gear oil depending on whether or not you have automatic trasmission or manual fill it up until you can put your finger in it and then rotate converter clock wise and it should slip into place before putting trasmission back into car and if after doing that and you still are having trouble take it to a transmission shop to have them do it for you.

Posted on Sep 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chugging noise when i accelerate


sounds like your throwout bearing is on its way out

Mar 11, 2012 | 2003 Honda Civic

1 Answer

Clutch problems


Hi bosslady15,

First of all I think I should say that clutches do not make grinding noises - but transmission gears do.
However, a clutch that is not disengaging properly can make the gears grind when trying to shift from one gear to the next. Also a common source of noise is the clutch throwout bearing. This will make a "grinding" or "growling" noise any time the clutch pedal is depressed. In either of these cases, the only solution is to replace the clutch, throwout bearing, pressure plate and pilot bushing. These all usually come in a clutch kit. If you have an hydraulic clutch with an internal slave cylinder it is recommended to replace the slave cylinder as well and also the flywheel on on vehicles. I'm sorry I cannot be more specific because you did not mention what type of vehicle we are talking about here.

Nov 07, 2011 | Cars & Trucks

1 Answer

Bad Throwout Bearing? I have a 1994 Jeep Cherokee Sport. Lately when my Jeep gets warmed up it will make a teakettle whistling noise. Note: this is a 5 speed standard transmission. The sound is more...


T.O. bearings usually do not make any contact when your foot is off the clutch pedal.
So it does not sound like a T.O. bearing.
But if it were an intake manifold leak, then it would idle badly.
You should be able to find it.
Listen through a piece of rubber hose, that you move around as a probe.
But if it changes when shifting, it is not likely an intake leak.
If it goes away when the clutch is pushed in, then it is likely the transmission input bearing.
If it is loudest when the clutch is pushed it, it could be the T.O. bearing, or the input shaft pilot bushing in the end of the crankshaft.

May 09, 2011 | 1994 Jeep Cherokee

1 Answer

Grinding type noise when the clutch is put in


You may have a bad throwout bearing which is not good as the transmission will need to be pulled to replace it, If replacing the throwout bearing it is usually a good idea to also replace the clutch plate at the same time. This can be caused by keeping pressure on the clutch pedal while driving causing the throwout bearing to be constantly engaged therefore wearing out the bearing.

Mar 03, 2011 | 1990 Daihatsu Rocky

1 Answer

There is a rattling noise in my engine compartment that increases with RPMs. It only goes away completely when I have the clutch fully pressed down and I'm at a complete stop. Therefore I thought it was a...


sounds like a transmission noise... have you checked the trans fluid?
try doing a flush and replace it with a product called Syncromesh FM from the gm dealership. what motor? stock? it did wonders for my 95 civic ex

Aug 04, 2010 | 1995 Honda Civic

1 Answer

94 civic ex clutch noise


Time to get the clutch, pressure plate, and throw out bearing replaced.
And on a car that old the pin or ball which the fork pivots should be replaced also.

Jul 08, 2010 | 1994 Honda Civic

2 Answers

Push in clutch and it makes a horriable grinding noise/ when release it stops and it goes into gear


It sounds like your throwout bearing is shot. There is a bearing called a throwout bearing that goes against the clutch forks when you push on the clutch, which causes the pressure plate to release the clutch which also releases tension from the input shaft which lets you change gears.
Replace that throwout bearing and I think you will find all your troubles gone. Hopefully it hasnt ruined the pressure plate forks. if your pressure plate forks are good there is not need to replace the clutch though if there is lots of miles on it you might choose to go ahead and do it since the transmission will be out anyway. Of course that is a lot more money. the choice is yours though so dont let a shop talk you into it if you dont want to.
Cheers.

Apr 21, 2010 | 1991 Nissan Pickup

2 Answers

Has a noise at idle,like a noisy input bearing to the gearbox, if I push the clutch in the noise stops. but the noise is not there all the time, I can make it make the noise, if I depress the clutch a few...


Throwout bearing is going out so it means you would have to remove the transmission, and also could have a bad pilot bearing out and or a broken clutch spring so it would still need to remove the transmission to fix it and then If it where me I would do a clutch job on it.

Jan 24, 2010 | 2001 Isuzu Rodeo

1 Answer

Car makes a metalic grinding noise when in neutral


You need a new throwout bearing in your clutch assembly.

Sep 10, 2009 | 1994 Pontiac Bonneville

1 Answer

Clutch/transmission problem


When the car is sitting idling,and the clutch is not depressed,it makes a grinding noise because the input shaft of the transmission is being forced to turn by the clutch,which is engaged,and even though the trans is in neutral,the input shaft is still turning,and this is called "neutral roll over" noise,and some of the assemblies inside the trans are freewheeling around.The noise goes away when the clutch pedal is being depressed down,because the input shaft of the transmission is no longer turning.So it does sound like an internal transmission problem.It is still possible for the throwout bearing to be bad,and it can be checked when the trans is removed from the vehicle,Remove the throwout bearing from the trans input sleeve,and press down on the bearing flange and turn it at the same time.It should feel smooth and free.If it catches or feels gravelly,then the bearing is bad and that could be your noise.Also,turn the input shaft of the trans and same thing,if it's smooth and free or if gravelly feeling......Good luck.

Jul 18, 2008 | 1993 Plymouth Colt

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...