Question about Mazda Cars & Trucks

Open Question

B2200 alignment specs - Mazda Cars & Trucks

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What are the wheel alignment specs for a 1997 Buick LeSabre Limited

Wheel aligned must be done on a special machine and any spec it subject to front end wear and can be adjusted for that, so base line specs are not set in stone and the job must be done on a computerized optical alignment machine.

Sep 09, 2016 | 1997 Buick LeSabre

1 Answer

How do you remove front left quarter panel on 1990 Mazda b2200 ute

There should be fasteners under the hood/bonnet as well as some behind the door. (Near where door hinges attach) and there might be some on the underside of the wheel well. Remove these carefully after you have marked reference points in multiple locations to assist with proper alignment when putting panel back on.

Aug 20, 2014 | Cars & Trucks

1 Answer

Why does my 93 Mazda B2200 still act like it is out of time?

indicates valve timing or ignition timing out
check the firing order as it could be 180 degrees out

Feb 16, 2018 | 1988 Mazda B2200

1 Answer

I need alignment specs for my 1987 300D, I took it to the alignment shop and thier alignment computer has 20-30 alignment profiles for a 1987 300d, they sue all sorts of codes and acronyms for the...

Hi I don't have the link .But put this in to google search - 40-0001 Test and adjustment values
That will give you them all .Hope it helps you ..

Dec 14, 2017 | 1987 Mercedes-Benz 300-Class

1 Answer

I need torque specs for the head on a 93 mazda b2200 2.2l 4 cylynder

First Step: 20 lb/ft
Sec Step: 40 lb/ft
3rd Step: 59-64 lb/ft

Feb 05, 2010 | 1988 Mazda B2200

1 Answer

87 B2200 Runs Rich

your throttle position sensor is maybe causing an overfuel,or the egr is plugged and when you rev it up,it is not burning the excess.if you leave it like that,the excess unburnt fuel will burn out your catalytic converter

Aug 18, 2009 | 1988 Mazda B2200

1 Answer

My 90 b2200 has been parked for a while...i had it aligned 5k mi ago before driving it cross country...not it pulls to the right rather hard, and when start to move it seems like the brake is still on..i...

sounds like you have a frozen brake caliper, lift right wheel off ground and remove tire, try to spin disk if you cannot then u need to remove caliper try using a c-clamp and compress inner pad and see if piston will move inward if yes check for leak and clean retry and if still doesn't work or cannot move piston in replace caliper. It most likely has rusted and seized from long term sitting.

Jul 16, 2009 | 1988 Mazda B2200

1 Answer

.005 clearance between crankshaft and timing belt sprocket.

mazdas specs for the crank are .985 but alot of cranks are made with a tolerence of .005 so from the factory alot of cranks are .005 to big are alittle smaller but both are right alittle play wont hurt it

Dec 13, 2008 | 1988 Mazda B2200

1 Answer

Mazda b2200 compression specs

those are average numbers and they are a little on the low but that is typical considering the age of the vehicle the compression should be 115 -120 psi.. hope this helps please rate this...thanks

Sep 24, 2008 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

80668 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides