Question about 2000 GMC Sonoma Extended Cab

Open Question

How do i remove the power steering pump from a 2000 GMC somona

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

pittmanc
  • 194 Answers

SOURCE: i don't know how to

this sould only be done by a professinal there are sepical tools used to bleed system

Posted on Dec 15, 2008

  • 12 Answers

SOURCE: removal of power steering pump on 1998 GMC Sierra 1500

you need a power steering pump puller the rest is simple any trouble let me know

Posted on Dec 24, 2008

shop242
  • 214 Answers

SOURCE: power steering on 2000 gmc qit working

Those are Notorius for the shafts in the pump itself breaking.. Remove the serpintine belt.. then grab the pulley on the ps pump and see if it pulls out.. if it does.. Pump Time Boys-n-Girls.. Hope this helps.. Thank you

Posted on Mar 12, 2009

c17hydro
  • 2984 Answers

SOURCE: replace power steering pump

NOTE: The following procedure requires the use of the GM Puller tool No. J–29785–A (1985–92), Puller J–25034–B (1993–96) or equivalent, and the GM Pulley Installer tool No. J–25033–B or equivalent.

  1. Disconnect the negative battery cable for safety.
  2. For 1996 vehicles, remove the air cleaner assembly for access.
  3. For 1993–96 vehicles, remove the hood latch and the upper fan shroud.
  4. Release tension and remove the drive belt. For details, please refer to Section 1 of this manual.
  5. Remove the power steering pump pulley using a suitable puller tool.
  6. Remove the power steering pump retaining bolts, then reposition the pump as necessary for access to the hoses.
  7. Position a fluid catch pan under the power steering pump.
  8. Remove the hoses from the power steering pump and drain the excess fluid into the catch pan.
  9. WARNING
    Be sure to cap all openings in the pump hydraulic system to prevent excessive fluid spillage and the possibility of system contamination.
  10. Remove the power steering pump from the vehicle. To install:
  11. Position the pump to the vehicle, then uncap and connect the pump hoses.
  12. Install the steering pump to the retaining bracket, then secure using the retaining bolts. Tighten the power steering pump-to-bracket bolts to 37 ft. lbs. (50 Nm). For 1996 vehicles, tighten the nut to 30 ft. lbs. (41 Nm). NOTE: On early-model vehicles where the drive belt is tensioned by pivoting the power steering pump assembly, do NOT fully tighten the mounting bolts at this time, since you will just have to loosen them again for belt installation and adjustment.
  13. Install the pump pulley using the GM Pulley Installer tool No. J–25033–B or equivalent. Press the drive pulley onto the power steering pump.
  14. Hand-tighten the pivot bolt, the adjusting bolt and the washer.
  15. Install the drive belt. On early-model vehicles so equipped, properly adjust the belt tension. For details on belt installation and tension adjustment, please refer to Section 1 of this manual.
  16. For 1993–96 vehicles install the upper fan shroud and the hood latch assembly.
  17. For 1996 vehicles, install the air cleaner assembly.
  18. Connect the negative battery cable.
  19. Refill the power steering reservoir and bleed the power steering system.
  20. Remove the jackstands and carefully lower the vehicle.
  21. Road test the vehicle, then check and top-off the power steering fluid.
Fig. 3: Removing the power steering pump pulley — 1985–92 vehicles

213c6a5.jpg
Email me at greg.bernett@mcchord.af.mil for an engine picture breakdown.

    Posted on Jul 22, 2009

    pippall
    • 1486 Answers

    SOURCE: power steering pump on my 1997 GMC K2500 truck??

    Check the power steering fluid level.Allso check the master cylinder level.Witch ever is low is your problem k

    Posted on Nov 08, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    I have a 2000 gmc 2500 I recently replaced my power steering pump and have trouble turning at low speeds I replaced my steering geat today and still have the problem


    See if you have "variable assist power steering" with a malfunction. A solenoid may be mounted on the steering rack, provides less PS at higher speeds, full power steering capability at slow speeds or when stopped. Your belt is tight for the pump?

    Aug 31, 2013 | GMC Cars & Trucks

    2 Answers

    Power steering pump 2000 gmc sonoma


    its not to bad take off the fan shroud it makes it easier

    Aug 17, 2012 | 2000 GMC Sonoma Extended Cab

    1 Answer

    2000 GMC Sierra 1/2 ton. Sounded like a wheel bearing might be going out. what it is just broke and you can not turn the wheel without pulling hard. Checked Steering Fluid full pump not frooze up what...


    Remove your belt and see if you can pull the power steering pump pulley off by hand. I have had the shaft of the pump break before and everything looks still good and fluid level still full. Then I removed the belt and the pulley and half of the broken shaft just pulled right out of the pump. The pump could still be bad even if the level is good. Lift front off of the ground and inspect your steering components and make sure your wheels turn freely.

    May 10, 2011 | 2000 GMC Sierra

    1 Answer

    How do I get my power steering pump out of 2002 yukon


    Hello walker_227,

    Removal Procedure:

    SPECIAL TOOLS: You will need a power steering pulley remover and installer tool, DO NOT USE A HAMMER.

    1. Remove the power steering pulley.
    2. Raise the vehicle.
    3. Remove the oil pan skid plate from the vehicle, if equipped.
    4. Place a drain pan under the vehicle.
    5. Remove the power steering pressure hose from the power steering pump from underneath the vehicle.
    6. Lower the vehicle.
    7. Remove the return hose from the power steering gearbox and the power steering pump.
    8. Remove the bolt retaining the rear bracket to the engine.(See picture below)
    9. Remove the bolts from the front of the pump.(See picture below)
    10. Remove the pump from the vehicle.
    11. Remove the bracket from the rear of the pump

    Installation Procedure:

    1. Reverse above procedure
    2.Fill and bleed the power steering system.

    netvan_20.png

    Mar 14, 2011 | 2004 GMC Yukon

    1 Answer

    Show me how to replace power steering pressure hose on 1995 GMC Yukon


    It's very easy, undo screw one end from back of power steering pump, no need to remove pump, and unscrew other end of hose from steering gear box, replace hose and top off with power steering fluid, when you undo power steering hose have a pan to catch the power steering fluid that will drip out.

    Aug 17, 2010 | GMC Yukon Cars & Trucks

    2 Answers

    How do I repair a leaking power steering hose?


    ok thees instructions that i have is for replacing the power steering pump but it has a great pic witch shows the power steering hoses i hope it helps


    NOTE The following procedure requires the use of the GM Puller toolNo. J-25034-B or equivalent, and the GM Pulley Installer tool No.J-25033-B or equivalent.
    1. Disconnect the negative battery cable for safety.
    2. Remove the air cleaner assembly for access.
    3. Release tension and remove the drive belt.
    4. Remove the power steering pump pulley using a suitable puller tool.
    5. Remove the power steering pump retaining bolts, then reposition the pump as necessary for access to the hoses.
    6. Position a fluid catch pan under the power steering pump.
    7. Remove the hoses from the power steering pump and drain the excess fluid into the catch pan.
      WARNING Be sure to cap all openings in the pump hydraulic system toprevent excessive fluid spillage and the possibility of systemcontamination.
    8. Remove the power steering pump from the vehicle.

      0900c15280227d22.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Pump pulley removal and installation


      0900c15280227d23.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Exploded view of the power steering pump mounting


      0900c15280227d24.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Typical power steering pump hose routing

    To install:
    1. Position the pump to the vehicle, then uncap and connect the pump hoses.
    2. Install the steering pump to the retaining bracket, then secureusing the retaining bolts. Tighten the nut to 30 ft. lbs. (41 Nm).
    3. Install the pump pulley using the GM Pulley Installer tool No.J-25033-B or equivalent. Press the drive pulley onto the power steeringpump.
    4. Hand-tighten the pivot bolt, the adjusting bolt and the washer.
    5. Install the drive belt.
    6. Install the air cleaner assembly.
    7. Connect the negative battery cable.
    8. Refill the power steering reservoir and bleed the power steering system.
    9. Road test the vehicle, then check and top-off the power steering fluid.

    Apr 23, 2009 | 2001 GMC Safari

    1 Answer

    Power steering fluid leaked out of 2000 GMC Jimmy


    well it went somewhere, check all the lines and look for signs of recent fluid leaks, it will be very apparent if u lost that much fluid, most likely it will either be the power sterering hoses or the front shaft seal of the pump.

    Mar 30, 2009 | 2000 GMC Jimmy

    1 Answer

    Power steering on 2000 gmc qit working


    Those are Notorius for the shafts in the pump itself breaking.. Remove the serpintine belt.. then grab the pulley on the ps pump and see if it pulls out.. if it does.. Pump Time Boys-n-Girls.. Hope this helps.. Thank you

    Mar 11, 2009 | 2001 GMC Yukon

    1 Answer

    Power steering


    blow that dang truck up

    Jan 22, 2009 | 2000 GMC Yukon

    1 Answer

    Removal of power steering pump on 1998 GMC Sierra 1500


    you need a power steering pump puller the rest is simple any trouble let me know

    Dec 14, 2008 | 1998 GMC Sierra

    Not finding what you are looking for?
    2000 GMC Sonoma Extended Cab Logo

    Related Topics:

    56 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    75197 Answers

    Freddy

    Level 3 Expert

    1311 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...