Question about Cars & Trucks

1 Answer

Tacoma wiring diagram

Brake lights come on when normal operating lights are turned on

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 188 Answers

There is a short in the tail lights. The wiring that powers the tail lights is shorting to the brake light wiring. Should be simple to find. Will be obvious unless it is in the rubber connector under the vehicle that will have to be cut and hard wired in.Check all connectors starting right at the light bulb itself!

Posted on Oct 21, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: no dome light on tacoma

The dome light gets 12 volt battery power at all times. The door switch, when the door is opened, allows the current to flow to ground, and completes the circuit. The door switch allows the ground to be made. Measure for 12 volts at the wiring connector, and measure for direct short at the ground wire, with the door open. The Ground wire is white with a black tracer.

Posted on Feb 27, 2009

AUTODOC01
  • 216 Answers

SOURCE: brake wiring diagram chevy lumina

why not just replace the turn signal switch must faster and safer . buy one from your local parts house then you can see its not that easy to install but you can do it with a little help

Posted on Aug 26, 2009

  • 30 Answers

SOURCE: i would like to know the wiring diagram for the

Search Toyota Schimatics online there are a few websites that can help you with that, Toyota is pretty good about shearing information about their product and makes it easy to fix your car yourselves. Hopes this helps

Posted on Mar 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brake esemble diagram


Hey Stan the man,need your vehicles info.,year,make,model and engine size and Tommy on the spot here will send you a picture diagram of your rear brake assembly.There's a special spring tool you can get at auto parts store to remove and install springs,me got one.

Oct 15, 2012 | Cars & Trucks

1 Answer

2004 Tacoma - tail lights don't work but brake lights and reverse lights do work. Bulbs look ok. fuse looks okay. Wiring looks ok. Could it be a relay or is there something else to check? Than


try cheaking the light switch its self may be faulty not normally a relay for but it shold tell you on fuse box which relay runs light ign ect

Sep 21, 2012 | 2007 Toyota Tacoma

1 Answer

Trying to get trailer wiring fixed. At the plug we have both brake lights and left turn signal, but nothing else. Have Mitchell's, but can't find trailer wiring diagram.


Check this site. Full of info and color codes. http://www.etrailer.com/faq-wiring.aspx
Did you use a direct plug that plugs into the harness or just a 4 way plug spliced in?
On this truck you will have to have a wiring converter... it will use turn signals and brake light (3 wires in) and convert them to a 2 wire which is what is required. Hope this helps, Mike

Dec 24, 2010 | 2003 Toyota Tacoma

1 Answer

How do I replace the brake light switch on my 1997 toyota tacoma?


The brake light switch is located on a bracket under the dash near the top of the brake pedal arm. To remove switch, disconnect wiring, loosen locknut and unscrew switch. Replacement is reverse procedure. To adjust, screw in switch until operating button is fully depressed by pedal arm, tighten locknut and reconnect wires. Check for correct operation of lights You may have to unscrew switch slightly to get best operation..

Nov 27, 2010 | Toyota Tacoma Cars & Trucks

1 Answer

How to wire a trailer for a 1998 toyota tacoma


you will need a converter box,..... because a trailer uses the same bulb for the tail/turn signal/brakes where as your truck uses seperate bulbs for turn/brake. Any parts store will have what you need and a diagram to wire the trailer.

Jul 24, 2010 | 1998 Toyota Tacoma

1 Answer

All brake lights out fuse is good and bulbs are good thinks its a ground but don't know where to look. found two wires in back of left rear light. one wire connected to body of truck goes nowhere else just...


BUY A HAYNES REPAIR MANUAL.IT HAS ALL EXTERIOR AND INTERIOR LIGHTS - HEAD LIGHTS AND BRAKE LIGHTS DIAGRAM.I SEEN MOST CARS AND TRUCKS THE TURN SIGNAL SWITCH IF GO BAD YOU WONT HAVE NO BRAKE LIGHTS. ITS SHARE THE SAME CIRCUIT WITH BRAKE LIGHTS .

Mar 30, 2010 | 2006 Toyota Tacoma

1 Answer

I would like to know the wiring diagram for the rear brake lights, turn signal's and parking lights to install a trailer harness on my 2006 toyota tacoma


Search Toyota Schimatics online there are a few websites that can help you with that, Toyota is pretty good about shearing information about their product and makes it easy to fix your car yourselves. Hopes this helps

Mar 05, 2010 | 2006 Toyota Tacoma

1 Answer

Hi, When I hook up my trailer, I get running


according to wiring diagram no module . do you have pwr at trailor connector. should be green w/ white wire coming into trailor connector. ( I believe pin 7 on connector ground should be pin 5 and is white with black wire )

Oct 25, 2009 | 2004 Toyota Tacoma

1 Answer

Rear lights not working


Toyotas sometimes have multiple power wires coming off of the battery to fuse blocks. One of these wires may be broken. Electrical schematics are available on-line or in repair manuals. If you don't have one, go to the library and look in the repair manual section.

Nov 10, 2008 | 1995 Toyota Tacoma

1 Answer

I need to add a trailer light plug to my truck. i need the tail light wiring diagram for a 2005 toyota tacoma pickup.


The diagram will do you no good it you do not have amber turn signals on your trailer. What you need is a "black box" that, when wired correctly, interprets the amber turn signal on the truck into a pulsed flash to the red brake lamp on the trailer. If the trailer does not have amber turn signals, it is impossible to wire a harness with a diagram. Sorry.

Aug 08, 2008 | 1995 Toyota Tacoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...