Question about 2001 Chrysler Concorde

1 Answer

Need to install brake booster - 2001 Chrysler Concorde

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 188 Answers

Does it have one to begin with? If it does, it's as simple as replacing the part. Unbolt and replace. There is a rod behind it that must be in place when installing. If not, there should be instructions with the new one you buy! Remove Master cyul. Do not spill fluid anywhere as it eats paint... Have to get the proper rod length and install it behind the booster. Hook up a vacuum line from the manifold intake to the booster with a one way check valve pointing towards the booster. Rod can be adjusted by pedal feel, but there are specs which I do not have on me! Mount master cyl. back onto booster and that should be it! Make sure there is room for the hood to close.....

Posted on Oct 21, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install breck booster


brake.
fsm book, install.
  1. On vehicles with an adjustable pushrod, adjust the brake booster rod so the measurement between the booster and the centerline of the clevis hole is 4.92 in. (15mm).
  2. Install the brake booster assembly and tighten the attaching nuts to 9-12 ft. lbs. (13-16 Nm).
  3. Adjust the master cylinder pushrod and install the master cylinder assembly.
  4. Connect the booster pushrod to the pedal clevis.
  5. Connect the vacuum lines to the brake booster.
  6. Connect the negative battery cable.
  7. Start the engine and check for proper brake operation.

Jun 26, 2014 | 1993 Nissan Altima

1 Answer

Replace brake booster


  • Slide the tube nut wrench over the brake line to the master cylinder connection. The master cylinder is normally on the driver's side of the engine bay and mounted on the firewall. Orient the wrench so that it fits over the tube nut on the end of the brake line.
  • 2Disconnect the brake line. Turn the nut counterclockwise to remove. Note the location of each brake line. There are four lines total, and they need to be put back in the same location when reinstalling the lines. You may want to mark them with masking tape and permanent marker.

  • 3Unplug the master cylinder cap electrical plug.
  • 4Remove the brake master cylinder to brake booster bolts with a socket wrench.
  • 5Back the master cylinder off the brake booster.
  • 6Unbolt the bolts holding the brake booster to the firewall on your vehicle.
  • 7Pull the cotter pin out of the brake pedal to brake booster connecting pin with a pair of pliers. This is done inside the vehicle down in the driver side foot well.
  • 8Pull the brake pedal to brake booster connecting pin out to disconnect the brake pedal from the brake booster connecting arm.
  • 9Mark and remove the vacuum hoses on the brake booster and slide the booster off the firewall.
  • 10Install the new brake booster. Installation is the reverse of removal
  • Aug 06, 2012 | 1998 Lincoln Mark VIII

    1 Answer

    I need instrustion to install a brake switch


    It is a generic Nissan brake light switch replacement procedure... the brake light switch on a Nissan Altima i.e. controls the illumination of the brake lights. Without the switch, the lights would not go on. The switch has no service life, so when it goes, it usually happens suddenly. New brake light switches can be obtained from Nissan or from a Nissan dealership.

    1. Remove the cotter pin from the pin bolt that holds the brake pedal to the brake booster with a pair of pliers. There is a small cotter pin running through the brake pedal to brake booster connection. You need to pull this cotter pin out to remove the larger pin that holds the brake pedal to the brake booster.
    2. Slide the pin out of the brake booster mounting bracket.
    3. Pull up on the brake pedal to slide it out of the brake booster mounting bracket.
    4. Remove the bolts holding the brake switch to the firewall using a socket wrench.
    5. Remove the electrical connector on the brake switch by pulling it straight off the switch.
    6. Slide the switch off the firewall.
    7. Install the new switch. Installation is the reverse of removal. Make sure that you replace the cotter pin in the brake booster to brake pedal connection. The cotter pin prevents the retaining pin in the brake booster mounting bracket from coming off.

    Hope helps (remember to rate this answer).

    Mar 31, 2011 | Nissan Altima Cars & Trucks

    2 Answers

    How do i change a brake booster


    from autozone.com:

    1. Disconnect the negative battery cable.
    2. Apply the parking brake.
    3. Unplug all necessary electrical connections.
    4. Remove the master cylinder from the booster and pull it off the studs, CAREFULLY! It is not necessary to disconnect the brake lines.
    5. Disconnect the vacuum hose from the check valve.
    6. If necessary, remove the brake light switch.
    7. Disconnect the booster pushrod at the brake pedal.
    8. Remove the booster mounting nuts, located on the inside of the firewall.

    24cafd9.gif


    Fig. Fig. 1: Vacuum booster mounting

    1. Lift off the booster and remove the gasket.

    To install:
    1. Install the booster with a new gasket.
    2. Tighten the booster mounting nuts to 21 ft. lbs. (29 Nm) on all except 1996-98 models. On 1996-98 models, tighten the nuts to 26 ft. lbs. (36 Nm).
    3. Install all remaining components.

    Oct 29, 2010 | 1998 Chevrolet Blazer

    1 Answer

    Need to replace brake power booster on 1992 buick limited with AB


    Heres a way to save you a lot of time. remove the two bolts that hold the master cylinder to booster, leave all brake lines connected, pull master away as far as it will go, you may have to pull on the line some, next go inside and remove the pin to remove the rod from brake pedal, you can let brake switch stay, back to booster, remove vacuum line from booster, back inside the car remove the 4 nuts that hold the booster to firewall, make sure rood is clear, go out and pull booster out and remove, install new booster make sure rod hooks to pedal before bolting it up, because sometimes the rod may go in the wrong direction, reverse directions to install, when your done theres no need to bleed brake system. hope this helps.

    Aug 31, 2010 | 1992 Buick LeSabre

    1 Answer

    K3500 hydraulic brake booster engages brakes when


    hello there:
    You will need to replace the brake booster to correct the problem in order to do this you will need to remove the push rod from you're brake arm separate the master cylinder from the booster and remove the four bolts on the booster and slide it out install in reverse hope this help you out sincerely D.Jones

    Jun 12, 2010 | 1996 Chevrolet C/K 3500

    1 Answer

    Any info on changing a brake booster on a 1996 Sierra and also help trouble shooting a master cy. Thanxlinder


    a defective master has just one common symptom, a soft sinking pedal.
    Instructions Things You'll Need:
    • Nose pliers
    • Ratchet and socket
    • Ratchet extension
    • Slip joint pliers
    • Wrench
    • New cotter pin
      Removing the Old Brake Booster
    1. Step 1 Park your car in a safe place with enough room to work around the front and driver side of the vehicle.
    2. Step 2 Locate the booster push rod connected to the brake pedal.
    3. Step 3 Remove the cotter pin securing the booster push rod pin to the brake pedal using a pair of nose pliers.
    4. Step 4 Release the push rod pin from the brake pedal and slide the push rod off the brake pedal.
    5. Step 5 Unscrew the four mounting nuts off the brake booster studs using a ratchet, ratchet extension and socket. You should be able to see the four booster studs extending through the firewall, in front of the brake pedal.
    6. Step 6 Disconnect the vacuum hose from the brake booster, working from the engine compartment. Use a pair of slip joint pliers.
    7. Step 7 Remove the two nuts holding the brake master cylinder to the brake booster. Use a wrench or ratchet and socket.
    8. Step 8 Separate the brake master cylinder from the booster just enough to make room for booster removal.
    9. Step 9 Pull the brake booster off the firewall and remove it from the vehicle.
      Installing the New Brake Booster
    10. Step 1 Set the new booster in place by sliding the push rod and four mounting studs through the mounting holes on the firewall.
    11. Step 2 Slide the brake master cylinder flange over the two mounting studs on the brake booster.
    12. Step 3 Start the two brake master cylinder mounting nuts by hand to avoid damage to the threads.
    13. Step 4 Tighten the two brake master cylinder mounting nuts using a wrench or ratchet and socket.
    14. Step 5 Connect the vacuum hose to the brake booster.
    15. Step 6 Screw the four mounting nuts to the brake booster working from inside the vehicle. Start the nuts by hand to avoid damaging the threads.
    16. Step 7 Tighten the four mounting nuts using the ratchet, ratchet extension and socket.
    17. Step 8 Position the brake booster push rod over the brake pedal and slide the push rod pin.
    18. Step 9 Install a new cotter pin to secure the booster push rod to the brake pedal

    Nov 20, 2009 | 1996 GMC Sierra

    1 Answer

    Replacing my brake booster


    go to the master cylinder and remove it from the booster, disconnect the vacuum line from the booster, then disconnect the brake plunger from your brake pedal inside the vehicle, then remove the booster mounting bolts from inside the vehicle then remove the booster, install in reverse order, once you install the master cylinder, you will need to bleed out any air in the brake system, hope this helps, let me know

    May 16, 2009 | 1996 Ford Ranger SuperCab

    1 Answer

    Need to replace a brake booster on a 1998 chevy cavalier


    get ready for some work.you need to remove the master cylinder nuts that hold master cylinder to brake booster.once you remove nuts you have 2 choices remove master cylinder to remove booster. to keep from bending brake lines.or you can leave master cylinder in pull it toward you easily careful dont bend lines .disconnect vacuum line at booster .go inside vechicle to floor on driver side loosen four nuts on floor to booster .disconnect power brake push rod from brake pedal .dont force pushrod to the sides when disconnecting it.remove four booster nuts then remove booster.when in stalling the new booster loosely install four nuts then connect the push rod to the brake pedal .install new clip tighten the booster unit .if you decide to remove master cylinder use inline wrenches on master cylinder to remove lines.also plug the master cylinder brake line holes to keep from losing all brake fluid.

    Apr 26, 2009 | 1998 Chevrolet Cavalier

    1 Answer

    1989 ford thunderbird std brake system vacuum booster install?


    There are a Couple of Different Variations on the Boosters. Make sure that you have the Correct one First. If you do, Just work it, Some of the Rods are Removeable by the Way.

    Jan 21, 2009 | 1989 Ford Thunderbird

    Not finding what you are looking for?
    2001 Chrysler Concorde Logo

    28 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8195 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...