Question about Honda Odyssey

1 Answer

Fitting drain pump

Where is it located

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 20,706 Answers

Tell us what your are doing first.
the car has many fluids , name it.

Posted on Nov 07, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I replace the Fuel Filter for chrysler cirrus 1999. Where is it located in the car?


The fuel filter mounts to the frame above the rear of the fuel tank. The inlet and outlet tubes are permanently attached to the filter.

REMOVAL

WARNING: RELEASE FUEL SYSTEM PRESSURE BEFORE DISCONNECTING QUICK- CONNECT FITTINGS AT FUEL FILTER AND FUEL PUMP MODULE. REFER TO THE FUEL PRESSURE RELEASE PROCEDURE .
  1. Remove rear seat.
  2. Disconnect fuel pump electrical connector. Push grommet out and feed jumper completely through hole in body.
  3. Remove fuel cap slowly to release tank pressure.
  4. With vehicle on a hoist, drain fuel from tank. Refer to Fuel Tank Draining.
  5. Remove driver's side fuel tank strap. Loosen, do not remove, passenger side fuel tank strap allowing fuel tank fill neck to touch rear suspension cross- member. WARNING: WRAP SHOP TOWELS AROUND HOSES TO CATCH ANY GASOLINE SPILLAGE .

Apr 19, 2017 | Chrysler Cars & Trucks

1 Answer

How To Drain Fuel Tank On 2005 Jeep Liberty Gas Tank


here is the Cherokee page.
read chapter, 14, page 19 on..
shows all way there, and is not easy.
why do this.
is pressure low
pump dead
is there 12vdc to pump cranking, (no? then dont do this)

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

i have the KJ pages here. (line # messed up)
Two different procedures may be used to drain fuel
tank: through the fuel fill fitting on tank, or using a
scan tool.
The quickest draining procedure involves removing
the rubber fuel fill hose (7) (Fig. 25) from fuel tank
fitting.
As an alternative procedure, the electric fuel pump
may be activated allowing tank to be drained at fuel
rail connection. Refer to DRB scan tool for fuel pump
activation procedures. Before disconnecting fuel line
at fuel rail, release fuel pressure. Refer to the Fuel
System Pressure Release Procedure for procedures.
Attach end of special test hose tool number 6541,
6539, 6631 or 6923 at fuel rail disconnection (tool
number will depend on model and/or engine application).
Position opposite end of this hose tool to an
approved gasoline draining station. Activate fuel
pump and drain tank until empty.
If electric fuel pump is not operating, fuel must be
drained through fuel fill fitting at tank. Refer to following
procedures.
(1) Release fuel system pressure.
(2) Raise vehicle.
(3) If equipped, remove fuel tank skid plate.
(4) Thoroughly clean area around fuel fill fitting
(6) (Fig. 26) and rubber fuel fill hose (1) at side of
fuel tank. After cleaning, loosen fuel fill hose clamp
(2) at tank.
(5) Before removing rubber hose (1) (Fig. 26) from
fitting, note hose orientation while referring to marks
(3) and (4).
6) Disconnect rubber fuel fill hose at fuel tank fitting
(2) (Fig. 27). Using an approved gas holding
tank, drain fuel tank through this fitting.
Tank Removal
(1) If equipped, remove fuel tank skid plate and
tow hooks. Certain equipment packages will also
require removal of the trailer hitch. Refer to Tow
Hooks, Trailer Hitch or Skid Plate in 23, Body for
removal/installation procedures.
(2) Disconnect and separate fresh air tube (6) (Fig.
28) quick-connect fitting.
(3) Disconnect air tubes at front of NVLD pump
(9) (Fig. 28).
(4) Disconnect NVLD pump (9) (Fig. 28) electrical
connector.
(5) Disconnect fuel pump module electrical connector
jumper. This is located near front of fuel tank.
(6) Support tank with a hydraulic jack.
(7) Remove 4 fuel tank strap bolts (10) (Fig. 28) (2
at front of tank; 2 at rear of tank), and remove both
tank support straps.
(8) Carefully lower tank a few inches.
(9) Continue lowering tank while guiding remaining
hoses and lines through plastic isolator sleeve (3)
(Fig. 29).
(10) If fuel tank is to be replaced, remove NVLD
pump and fuel pump module from tank. Refer to
Fuel Pump Module Removal/Installation procedures.
end , tank out.

why not login to alldata.com and read
or buy the FSM,, and get all pages of chapter 14, end to end.

Oct 19, 2015 | 2005 Jeep Liberty

1 Answer

Steering leak hose fitting.


yes replace including fittings

Feb 04, 2014 | 2002 Mazda Tribute

2 Answers

Where to put transmission fluid in lincoln ls 05


you need a long skinny funnel ,find the transmission dip stick most likely to be on the driver side under hood place funnel in dip stick hole and pour

May 17, 2011 | 2005 Lincoln LS

1 Answer

Installing water pump in 97 cavalier 2.2


Hi. Here's the proceudere on how to replace the water pump of your 97 Chevy Cavalier.


•1
Drain the cooling system. Place a large oil drain container under the drain fitting located on the bottom of the radiator. Turn the drain fitting counterclockwise until fluid is draining from the radiator. Use a pair of pliers to turn the drain fitting if you cannot turn it by hand. Turn the fitting clockwise to tighten it after all of the fluid has drained from the radiator.
•2
Remove the cooling fan. Disconnect the electrical connection from the fan motor. Remove the bolts holding the fan assembly to the radiator support with a ratchet wrench. Pull the fan assembly up from the engine compartment and remove it.
•3
Remove the serpentine belt. Place a wrench over the belt tensioner and rotate the tensioner to release the tension on the belt. Pull the belt off the pulleys and remove it from the vehicle.
•4
Remove the water pump pulley. Place a screwdriver behind the pulley to lock it in place while removing the pulley mounting bolts with a ratchet wrench.
•5
Disconnect the coolant hoses running to the water pump.
•6
Remove the water pump mounting bolts with a ratchet wrench or wrench and remove the water pump from the vehicle.
•7
Clean the mating surfaces of the engine block and new water pump with a towel saturated with lacquer thinner.
•8
Apply a thin layer of RTV sealer to both sides of the new water pump gasket and place the gasket on the new water pump.
•9
Place the water pump against the engine block and finger tighten the water pump mounting bolts to hold the pump in place. Tighten the bolts with a torque wrench to 18 foot-pounds.
•10
Place the pulley on the water pump and install the water pump pulley mounting bolts with a ratchet wrench.
•11
Attach any hoses previously disconnected from the water pump.
•12
Install the serpentine belt. Route the belt over the pulleys according to the routing diagram in the engine compartment. Place a wrench over the belt tensioner and rotate the tensioner to tighten the tension on the belt.
•13
Install the cooling fan. Gently lower the cooling fan in position and install the mounting bolts attaching the fan assembly to the radiator support with a ratchet wrench. Attach the electrical connection to the fan motor.
•14
Refill the cooling system to the appropriate level, start the vehicle and check for leaks around the water pump.

All the best!

Nov 10, 2010 | 1997 Chevrolet Cavalier

1 Answer

How do I change a water pump on a 2004 kia sorento?


Kia Sorento 2003-05
Water Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

  9. dc45c19.jpg

    Fig. Water pump and timing belt assembly-exploded view

To install:

1016213.jpg

Fig. Water pump bolt locations
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. Refill the coolant.
  7. Run the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

To install:


e9be8c3.jpg

Fig. Water pump bolt locations

596080e.jpg

Fig. Water pump O-ring installation
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. To adjust the drive belt tension, hang the belt on the pulley of the tensioner and install the tensioner.
    NOTE If the tensioner is already installed, loosen its mounting bolts to allow belt installation
  7. Install the drive belt.
  8. Adjust the belt tension to specification by turning the adjusting bolt clockwise or counterclockwise.
  9. Air conditioning belt tension should be 0.28-0.039 inch. Alternator belt tension should be 0.39-0.051 inch. Power steering belt tension should be 0.31-0.051 inch.
  10. Torque the tensioner assembly bolt to 33-36 ft. lbs. (45-50 Nm).
  11. Refill the coolant.
  12. Run the engine and check for leaks.

TY for using Fixya; remember comment and rated this.

Apr 01, 2010 | 2004 Kia Sorento

1 Answer

How do you change a fuel filter on a 97 dodge stratus


Fig. 7 Fuel Lines At Fuel Pump Module 42402626 NOTE: The fuel filter mounts to the frame above the rear of the fuel tank. The inlet and outlet tubes are permanently attached to the filter.
REMOVAL
  1. Release fuel system pressure.
  2. From inside trunk, disconnect fuel pump module wiring jumper from main body harness.
    • The 4 pin connector is located under the trunk mat on the left side of trunk near the base of the shock tower.
    • Locate body grommet for jumper near base of rear seat. Push grommet out and feed jumper completely through hole in body.
  1. Remove fuel cap slowly to release tank pressure.
  2. With vehicle on a hoist, drain fuel from tank. Support fuel tank with a support such as a transmission jack stand.
  3. Position a fuel approved container, with a capacity of at least 16 gallons, under the drain plug located on the bottom left edge of the tank.
  4. Remove drain plug and allow fuel to drain. WARNING: Drain plug must be installed at this time as there will be 1 to 2 gallons of fuel left in the tank .
  5. When tank is no longer draining, install drain plug. Tighten plug to 32 in lb .
  6. Remove driver's side fuel tank strap.
    • Loosen, do not remove, passenger side fuel tank strap allowing fuel tank fill neck to touch rear suspension cross-member.
WARNING: Wrap shop towels around hoses to catch any gasoline spillage .

  1. Disconnect fuel lines from fuel pump module Fig. 7 . These are quick connect fittings.
  2. Disconnect fuel supply line from the fuel brake module.
Fig. 8 Fuel Filter 42402627
  1. Remove fuel filter Fig. 8 .
NOTE: The fuel supply (to filter) tube, return tube (to pump module) are permanently attached to the fuel filter.
  • The ends of the fuel supply and return tubes have different size quick-connect fittings.
  • The larger quick-connect fitting connects to the large nipple (supply side) on the fuel pump module.
  • The smaller quick-connect fitting attaches to the small nipple (return side) on the fuel pump module.
Apply a light coating of clean 30 weight engine oil to the fuel filter nipples. Install fuel tubes.
  1. Install fuel tank, filter and tank straps. Torque tank strap bolts to 23 Nm (250 in lbs) . Make sure pump module harness grommet is installed in body as tank is raised into position.
  2. Lower vehicle and connect pump module connector.
  3. Fill tank with fuel.
  4. Connect negative cable to auxiliary jumper terminal.

Dec 11, 2009 | 1997 Dodge Stratus

1 Answer

REPLACEMENT of a fuel filter on a 1997


cd7cd12.gif
The fuel filter (1) is mounted next to the fuel pump module (2), on top of the fuel tank (3)


The fuel delivery system uses quick-connect fittings. The fuel filter mounts to the top of the fuel tank.
  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. Place a drain pan underneath the fuel filter to catch any spilling fuel that will result from disconnecting the fuel lines.
It may be necessary to support the weight of the fuel tank with a block of wood and a floor jack. Once this is accomplished, loosen, but do not remove, the fuel tank strap bolts. Allow the fuel tank to lower just enough to access the fuel line fittings at the fuel pump module.

6036176.gif

Disengage the fuel line quick-connect fittings from the fuel pump module

02627d0.gif
Be sure to place a drain pan underneath the filter line fittings to catch all fuel spillage

Locate the fuel filter in its mounting on top of the fuel tank. Detach the quick-connect fittings from the chassis fuel supply tube and fuel pump module by squeezing the quick-connect fitting retainer tabs together and pulling the fitting assembly away from the fuel line nipple. The retainer will remain on the fuel tube.

df40422.gif
Using a 10mm socket, remove the fuel filter mounting bolt ...

e9542f8.gif
... then remove the fuel filter from the top of the fuel tank

  1. Remove the fuel filter mounting bolt and remove the fuel filter from the fuel tank.
To install:
  1. Install the fuel filter on the top of the fuel tank and tighten the mounting bolt.
  2. The fuel supply tube (to chassis fuel line), return tube (to pump module) and fuel supply (to fuel filter) tube are permanently attached to the fuel filter. The quick-connect fitting ends of the fuel supply and return tubes are of different sizes.
  3. Apply a light coating of 30W engine oil to the nipples of the fuel filter.
  4. Push the quick-connect fitting over the fuel line until the retainer seats and clicks into place. Be sure the retainer tabs have locked into the case of the fitting.
  5. If necessary, raise the fuel tank and tighten the fuel tank strap bolts.
  6. Lower the vehicle. Start the engine and check for leaks.

Nov 30, 2009 | 1997 Chrysler Town & Country

1 Answer

How do I change a fuel pump on my 1995 Ford F350 7.3 2WD Power Stroke Diesel Do I have to worry about the timing eccentric? How and what do I rotate?


Hi, I hope this helps...

1994-96 Engines
See Figures 3 and 4



0900c15280262dd1.jpg Fig. Fig. 3: Details of the fuel pump assembly-1994-96 diesel engine



0900c15280262dd2.jpg Fig. Fig. 4: View of the fuel pump-1994-96 diesel engine
  1. Remove the turbocharger assembly.
  2. Remove the fuel line banjo bolt at the pump.
  3. Remove the fuel line fittings at the rear of the cylinder heads.
  4. Remove the fuel lines assembly.
  5. Loosen the two hose clamps at the fuel pump fittings.
  6. Disconnect the water drain hose at the fuel filter.
  7. Disconnect the filter and position it forward.
  8. Remove the fuel pump retaining bolts, then lift the pump out of the crankcase bore.
  9. Remove the fuel pump tappet from the crankcase bore.

To install:
  1. Rotate the engine so the fuel pump eccentric is on the base circle.
  2. Install the fuel pump tappet in the base of the fuel pump.
  3. Replace the O-ring on the fuel pump base.
  4. Install the fuel pump and bolt it in place.
  5. Install the fuel filter and connect the water drain hose.
  6. Connect the two fuel hoses at the front of the fuel pump.
  7. Tighten the fuel line clamps and install the fuel filter retaining bolts.
  8. Install the fuel line assembly and new seal rings at the rear of the pump.
  9. Loosely install the fuel line fittings at the rear of the cylinder heads.
  10. Install the fuel line banjo fitting at the pump. Tighten the fitting to 40 ft. lbs. (54 Nm).
  11. Tighten the fuel line fittings.
  12. Install the turbocharger assembly.

Oct 13, 2009 | 1995 Ford F350

2 Answers

1999 jeep cherokee do you have to remove the fuel pump to replace


The combination Fuel Filter/Fuel Pressure Regulator is located on the fuel pump module. The fuel pump module is located on top of fuel tank.

The filter/regulator may be removed without removing fuel pump module although fuel tank must be removed.

REMOVAL
  1. Remove fuel tank. Refer to Fuel Tank Removal/Installation.
  2. Clean area around filter/regulator.
  3. Disconnect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
  4. Remove retainer clamp from top of filter/regulator. Clamp snaps to tabs on pump module. Discard old clamp.
  5. Pry filter/regulator from top of pump module with 2 screwdrivers. Unit is snapped into module
  6. Discard gasket below filter/regulator.
    1. Before discarding filter/regulator assembly, inspect assembly to verify that O-rings are intact. If the smallest of the two O-rings can not be found on bottom of filter/regulator, it may be necessary to remove it from the fuel inlet passage in fuel pump module.
    INSTALLATION
    1. Clean recessed area in pump module where filter/regulator is to be installed.
    2. Obtain new filter/regulator (two new O-rings should already be installed)
    3. Apply a small amount of clean engine oil to O-rings. Do not install O-rings separately into fuel pump module. They will be damaged when installing filter/regulator.
    4. Install new gasket to top of fuel pump module.
    5. Press new filter/regulator into top of pump module until it snaps into position (a positive click must be heard or felt).
    6. The arrow molded into top of fuel pump module should be pointed towards front of vehicle (12 O'clock position).
    7. Rotate filter/regulator until fuel supply tube (fitting) is pointed towards front of vehicle (12 O'clock position).
    8. Install new retainer clamp (clamp snaps over top of filter/regulator and locks to flanges on pump module).
    9. Connect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
    10. Install fuel tank. Refer to Fuel Tank Removal/Installation.
WARNING: THE FUEL SYSTEM IS UNDER CONSTANT FUEL PRESSURE EVEN WITH THE ENGINE OFF. THIS PRESSURE MUST BE RELEASED BEFORE SERVICING FUEL TANK .

Two different procedures may be used to drain fuel tank (lowering tank or using DRB scan tool).

The quickest draining procedure involves lowering the fuel tank.

As an alternative procedure, the electric fuel pump may be activated allowing tank to be drained at fuel rail connection. Refer to DRB scan tool for fuel pump activation procedures. Before disconnecting fuel line at fuel rail, release fuel pressure. Refer to the Fuel System Pressure Release Procedure for procedures. Attach end of special test hose tool number 6541, 6539, 6631 or 6923 at fuel rail disconnection (tool number will depend on model and/or engine application). Position opposite end of this hose tool to an approved gasoline draining station. Activate fuel pump and drain tank until empty.

If electric fuel pump is not operating, tank must be lowered for fuel draining. Refer to following procedures.

FUEL TANK REMOVAL
  1. Disconnect negative battery cable at battery.
  2. Release fuel system pressure. Refer to the Fuel System Pressure Release.
  3. Raise and support vehicle.
  4. If Equipped: Remove fuel tank skid plate.
  5. Remove 4 fuel hose shield mounting bolts and remove fuel hose shield from body.
    1. Remove fuel tank fill hose and vent hose clamps at fuel tank filler tube. Remove both hoses at fuel filler tube.
    2. Remove exhaust tailpipe heat shield mounting bolts and remove shield. CAUTION: To protect fuel tank from exhaust heat, this shield must reinstalled after tank installation.
    3. Place a hydraulic jack to bottom of fuel tank. WARNING: PLACE A SHOP TOWEL AROUND FUEL LINES TO CATCH ANY EXCESS FUEL .
      1. Disconnect fuel supply line from fuel extension line near front of fuel tank. Refer to Fuel Tubes/Lines/Hoses and Clamps. Also refer to Quick-Connect Fittings for procedures.
      2. Disconnect EVAP canister vent line near front of tank.
      3. Disconnect fuel pump module electrical connector (pigtail harness) near front of tank. Harness connector is clipped to body.
        1. Remove two fuel tank strap nuts. Position both tank support straps away from tank.
        2. Carefully lower right side of tank while feeding both fuel hoses through access hole in body. Fuel Tank Full And Not Drained Using DRB Scan Tool: To prevent fuel loss through hoses, keep left side of tank higher than right side while lowering. Do not allow hose openings to drop lower than top of tank.
        3. Continue lowering tank until clear of vehicle. Place tank on floor with left side (hose side) higher than right side
          1. Drain tank by removing fuel fill hose at tank. Fuel fill hose is largest of 2 hoses. Insert the drain hose (from an approved gasoline draining station) into hose opening. Drain tank until empty.
          2. If fuel pump module removal is necessary, refer to Fuel Pump Module Removal/installation for procedures.
          INSTALLATION
          1. If fuel pump module is being installed, refer to Fuel Pump Module Removal/installation for procedures.
          2. Install fuel fill/vent hoses to tank fittings. To prevent hose from kinking, rotate each hose until index mark on hose is aligned to index tang on fuel tank.
          3. Install hose clamps to hoses. Position clamps between index marks on each hose.
          4. Position fuel tank to hydraulic jack.
          5. Raise tank into position while guiding fuel fill and vent hoses into and through access hole in body.
          6. Continue raising tank until positioned to body.
          7. Attach two fuel tank mounting straps and mounting nuts. Tighten nuts to 10 Nm (90 in. lbs.) torque. Do not over tighten nuts.
          8. Install both fuel hoses to fuel fill tube. Tighten both retaining clamps.
          9. Position fuel hose shield to body. Install and tighten 4 mounting bolts.
          10. Connect fuel pump module pigtail harness electrical connector near front of tank.
          11. Connect fuel pump module supply line near front of tank. Refer to Quick-Connect Fittings for procedures.
          12. Connect EVAP hose near front of tank.
          13. Install exhaust tailpipe heat shield.
          1. Install fuel tank skid plate (if equipped).
          1. Lower vehicle and connect battery cable to battery.

Feb 08, 2009 | 1999 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...