Question about Cars & Trucks

Open Question

Denso wiper motor wire color code

Looking for the wire color code on 98 S10 Blazer rear(tailgate) wiper motor

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jimbopickens
  • 56 Answers

SOURCE: 98 chevy s10 blazer turn signal

Unplug the turn signal relay from the fuse box and start you engine. Does it still make that noise?
If yes... Put the relay back in, that is not the problem.
If No...Then the relay could be bad, replace it!

PLEASE RATE THIS SOLUTION! Thank You Very Much!

Posted on Nov 25, 2008

  • 1 Answer

SOURCE: changing wiper motor in chev s10

It's not bad. They make a special tool to remove the motor from the arm assembly, but with a little determination I was able to remove it with out the tool. If your wipers aren't working try running power to the motor first to test it. I swapped it out and the problem ended up being a bad ground in the switch. I bypassed that for a little while by running a jumper wire from the engine block to motor. It also could be the pulse module they are known for going bad in GM vehicles.

Posted on Jan 21, 2009

localwonder
  • 6784 Answers

SOURCE: rear window wiper wiring diagram

this website is great for retrieving wiring diagrams.

Posted on Feb 11, 2009

c17hydro
  • 2984 Answers

SOURCE: my 2001 Town and Country's rear windshield wiper

Pretty straight forward.....here are the steps:

Please don't forget to rate--

Rear Window Wiper Motor Removal & Installation To Remove:

  1. Disconnect and isolate the negative battery cable.
  2. Remove the rear wiper arm.
  3. Open the liftgate.
  4. Perform the following to remove the liftgate trim panel.
    • If equipped, remove the lift motor link
    • Remove the upper frame molding
    • Remove assist handle screws
    • Disengage the hidden clips around perimeter of liftgate trim
    • Disconnect the electrical connectors.
  5. Disconnect the wire connector from the wiper motor.
  6. Remove the wiper motor mounting screws.
  7. Remove the wiper motor.
To Install:
  1. Position the wiper motor in the liftgate.
  2. Install the wiper motor mounting screws.
  3. Connect the wiring connector.
  4. Install the liftgate trim panel.
  5. Close the liftgate.

Posted on Jul 24, 2009

  • 701 Answers

SOURCE: wheres the circuit board for a windshield wiper

Hello jlwhelchel: My name is Roger and I will answer your question. Raise the hood locate the wiper motor. Remove the cover held on by three screws. Remove the cover. The cover is the module.
Should you need further help please just ask. Please rate the answer. This way I know the information was helpful. Thank You for using Fix Ya. Roger

Posted on Oct 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a color code for the brake light wiring diagram for a 2000 s10 blazer


The S10 and the Blazer are identified as two different vehicles. The left stop light wire is YEL; the right is DK GRN. The center high mount stop lamp wire is LT BLU.

Oct 30, 2016 | 2000 Chevrolet Blazer

1 Answer

85 s10 Chevy blazer: back window and tailgate won't open


Very typical for the window motor to fail. The tailgate will not open when the window isn't rolled down. If there is voltage to the terminals of the window motor when you actuate the switch but the motor does not turn, replace the motor. Once you are able to roll the window down, the tailgate should open again.

Apr 08, 2014 | Cars & Trucks

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

HOW DO YOU REPLACE THE REAR WIPER MOTOR ON A 2003 JEEP LIBERTY?


REMOVAL
  1. Disconnect and isolate the battery negative cable.
  2. Remove the rear wiper arm from the rear wiper motor output shaft.
  3. Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel .Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
  4. Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel
  5. Remove the bezel and gasket from the rear wiper motor output shaft.
  6. Remove the trim panel from the tailgate inner panel.
  7. Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
  8. Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle
  9. Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
  10. Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
  11. Remove the rear wiper motor and mounting bracket from the tailgate as a unit.
To Install just reverse steps

Jan 23, 2011 | 2003 Jeep Liberty

1 Answer

Rear window wiper stop working


one of two possible problems.. (trusting fuse is ok) first is that the wires in the hinge area are prone to breakage. second is that the rear wipers are subject to vast amounts of dirt/salt the shaft of the wiper can leak into the bearings and seize them solid. i would remove the plastic tailgate cover and meter the wires off the wiper and if there is power then you are looking at the motor. hope this helps

Dec 31, 2010 | 2005 Pontiac Montana SV6

1 Answer

Rear windshield wiper not working


There's actually a motor in the rear tailgate for the rear wiper. I had mine go out right out of nowhere. The new one from any auto parts store should also come with directions on how to put it in. Not too bad of a repair at all. Hope this helps.

Nov 14, 2010 | 1997 Chevrolet Blazer

1 Answer

1999 chevy blazer...where is the reservoir to fill the wiper fluid for the back window? Is it located somewhere by the back tailgate, or is it supposed to use the same wiper fluid from the front reservoir....


1999 blazer i m pretty sure uses the same reservoir, its easy to check, look at bootom of res and there should be to pumps. a good way to test wiring and washer button is to wire the rear to frt and hit rear washer button and it should spray frt window, or just use a test light and check for a good ground and power when button is hit hope this helps.

Feb 28, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

My 2001 Town and Country's rear windshield wiper motor is kaput. How do I change it without destroying the rear tailgate paneling


Pretty straight forward.....here are the steps:

Please don't forget to rate--

Rear Window Wiper Motor Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove the rear wiper arm.
  3. Open the liftgate.
  4. Perform the following to remove the liftgate trim panel.
    • If equipped, remove the lift motor link
    • Remove the upper frame molding
    • Remove assist handle screws
    • Disengage the hidden clips around perimeter of liftgate trim
    • Disconnect the electrical connectors.
  5. Disconnect the wire connector from the wiper motor.
  6. Remove the wiper motor mounting screws.
  7. Remove the wiper motor.
To Install:
  1. Position the wiper motor in the liftgate.
  2. Install the wiper motor mounting screws.
  3. Connect the wiring connector.
  4. Install the liftgate trim panel.
  5. Close the liftgate.

Jul 24, 2009 | 2001 Chrysler Town & Country

1 Answer

1996 a6 quattro wagon rear wiper not working


motor could be seized but more often than not its the wires from the car body into the rear tailgate ,their is a rubber cover at the top where the hinges are see if wires are damaged in their.i have often disconnected rear wipers as the owners complain they will not turn off once activated unless you turn ignition off to reset them so remove door panel to check for that after checking wires where they leave car body for the tailgate

Nov 27, 2008 | 1996 Audi A6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...