Question about Cars & Trucks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Below is the diagram you needed. This is an updated one per ALLDATA as some changes were made so the one below it with the X over it is the wrong way that many manuals are saying. It's done in two passes for final torque I hope this helps and good luck.
Posted on Oct 29, 2011
Are you aware that besides the torque, the cylider head bolts MUST be torqued in a specific sequence. The Ft/lbs of torque and the sequence are only available in the cars service manual or something similar like Chiltons repair manual. You can browse a copy of the Chiltons at a local library or bookstore and write down the ft/lbs and sequence. I've done it myself to save a few bucks
Posted on Mar 08, 2010
Install the cylinder head bolts. Starting at top center, tighten all
cylinder head bolts in sequence as shown in illustration, using the
Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the
procedure, re-tightening all cylinder head bolt to the specified torque.
(torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
. Install the timing belt tensioner pulley.
. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
. Adjust the timing according to "Timing Belt"
. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:
2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)
. Install the timing belt cover.
Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
. Install the surge tank and tighten the nuts bolts to the specified torque.
. Install the power steering oil pump and bracket.
. Install the ignition coil.
. Install the air intake hose.
Connect the vacuum hose, fuel hose and water hose.
. Install breather hose.
Posted on Dec 22, 2010
According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Posted on Feb 14, 2011
Tips for a great answer:
Feb 02, 2017 | Hyundai Accent Cars & Trucks
Dec 29, 2015 | Hyundai Cars & Trucks
Dec 19, 2015 | Hyundai Cars & Trucks
Mar 02, 2014 | 1997 Hyundai Accent
Apr 21, 2011 | 2005 Hyundai Accent
Dec 22, 2010 | 2004 Hyundai Elantra
Dec 19, 2010 | Hyundai Motor 1998 Accent
Apr 08, 2010 | 2001 Hyundai Accent
Mar 08, 2010 | 2001 Hyundai Accent
57 people viewed this question
Usually answered in minutes!