Question about Cars & Trucks

Open Question

Neutral safety switch wh statesman - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2004 Jeep Grand Chrokee Neutral Safety Switch Location

The switch is on the transmission..It is usually a dealer item but you can get one from Rockauto.com for about 1/4 of what the dealers charge.

Posted on May 25, 2009

emissionwiz
  • 75797 Answers

SOURCE: Neutral Safety Switch Location

on the transmission where the shift cable attaches.

Posted on Jun 15, 2009

  • 1129 Answers

SOURCE: neutral safety switch

It is located on the side of the transmission, follow the shift cable down to it you will recognize it because it has a electrical wire comming off it and either a shift lever or shift cable going to it.

Posted on Jul 14, 2009

canbruce75
  • 1776 Answers

SOURCE: removing neutral safety switch

Check out the autozone website at autozone.com and register your vehicle. It is free and will give you access to an online repair manual for the vehicle. The steps for removing the neutral safety switch can be found there. Hope this helped. Best wishes.

Posted on Aug 03, 2009

ZJLimited
  • 17970 Answers

SOURCE: Looking for the neutral safety switch

Neutral Safety/Back-up Light Switch

This is a combination switch which controls both Neutral Safety and Back-up lamp circuits.

C6 Transmission


8290dff.jpg

C6 neutral start switch

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Remove the downshift linkage rod return spring at the low-reverse servo cover.
  4. Coat the outer lever attaching nut with penetrating oil. Remove the nut and lever.
  5. Remove the 2 switch attaching bolts, disconnect the wiring at the connectors and remove the switch.
  6. Installation is the reverse of removal. Adjust the switch and tighten the bolts to 55-75 inch lbs. (6.2-8.5 Nm).
  7. Remove the jackstands and lower the vehicle.
  8. Connect the negative battery cable.
AOD Transmission

e7f4231.jpg

Removing the AOD neutral start switch
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disconnect the wiring from the switch.
  4. Using a deep socket, unscrew the switch.
  5. Installation is the reverse of removal. Tighten the switch to 10 ft. lbs. (14 Nm).
  6. Remove the jackstands and lower the vehicle.
  7. Connect the negative battery cable.
4R70W Transmission

2f68dfc.jpg


Removing the Manual Lever Position (MLP) sensor

As of 1994, the neutral safety switch is referred to as a Manual Lever Position Sensor (MLP).
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Disengage the harness connector from the MLP sensor.
  4. Remove the 2 sensor attaching bolts and remove the sensor.
To install:
  1. Install the MLP sensor and install retaining bolts. Do not tighten, the sensor requires adjustment.
  2. Adjust the MLP sensor then tighten attaching screws to 80-100 inch lbs. (9-11 Nm).
  3. Remove the jackstands and lower the vehicle.
  4. Connect the negative battery cable.


ADJUSTMENT

C6 Transmission
  1. Hold the steering column transmission selector lever against the Neutral stop.
  2. Move the sliding block assembly on the neutral switch to the Neutral position and insert a 0.091 in. (2.3mm) gauge pin in the alignment hole on the terminal side of the switch.
  3. Move the switch assembly housing so that the sliding block contacts the actuating pin lever. Secure the switch to the outer tube of the steering column and remove the gauge pin.
  4. Check the operation of the switch. The engine should only start in Neutral and Park .

4R70W Transmission


4cc4151.jpg


Adjusting the MLP sensor

Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.
  1. Position the manual control lever in Neutral .
  2. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  3. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  4. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).

I hope help you. Good luck (rated this help).

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 WH Statesman. 2001 VX SS Commodore


every possibility that it will as the statesman is just a glorified commodore any way
GM holden used as many common parts as possible to keep prices down

Oct 10, 2016 | Cars & Trucks

1 Answer

Vacuum diagram wh L67 1999 holden statesman ?


I've just put L67 vacuum lines into "images" on bing and got all sorts of pictures, start there?

Nov 15, 2014 | Cars & Trucks

1 Answer

Wh won't start all the time


you shold check your battery first
__________
x-vci tool

Sep 17, 2012 | 1992 Holden VQ Statesman

1 Answer

Wiring color code for steering wheel controller for a wh statesman


We do not have wiring diagrams here at fixya, sorry.

Aug 25, 2012 | Holden HSV Cars & Trucks

1 Answer

Is it easy to change my fuel filter on my wh statesman


Yes you need a special tool to release the fuel line.

Jun 28, 2012 | Cars & Trucks

2 Answers

99 Chevrolet S-10 Removal of Transmission Front Pump Seal


Just a seal removal tool or a screw driver, pops right out.

Feb 17, 2010 | 2003 Chevrolet Tahoe

1 Answer

04 Envoy xuv 4 wh. drv. stays in 4 wh drv. HI


Try putting your transmission in neutral and slowly shifting the 4wd selector to each position but you have to wait a few seconds between selsctions as it has to go through your vehicles computer, shifting to fast will cause your symptoms. I hope this helped you out. Roger

Feb 08, 2010 | 2004 GMC Canyon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...