Question about Cars & Trucks

Open Question

Stabilitrak Bad vibration. Then stabilitytrk is engaged but still the same ,if I go over 45mph it gets worse

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: 2001 Jeep Cherokee Vibration at highway speeds

That kind of vibration generally can be associated with a binding universal joint. Sometimes you can see a bit of rust around the seals, sometimes not. The "shake" test is generally valid only with vehicle off the ground and trans in neutral, but sometimes the bearings are fused with rust and do not move.If "eyeball" inspection reveals nothing , remove the driveshaft (s) and physically move joints. If overly loose or binding they are bad. If after complete inspection you still come up with nothing then it's time to look at other "oddball" things.
good luck

Posted on Jan 15, 2009

jswizzzzzle
  • 74 Answers

SOURCE: hard vibrations at 45mph or more

two things would do this that I can think of right now. wheel balance, and or driveshaft balance. I would go get my wheels balanced at a shop first.

Posted on Feb 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rotated & balanced tires. new driveshaft & center carrier bearing u-joints new shocks front & rear replaced rear axle bearings and seals new left rear rotor parking brake shoes new disc brake...


You will need to check things logically. Run the truck in the air and note where the vibration is at. Take the wheels OFF and put a few lug nuts to hold the rotors on, take the truck to 45mph or whatever the vibration is the worst. is it still there? if its gone, check wheels/ tires. if its still there, check rotors, axles. A drive shaft will make a rapid vibration at low speeds since it turns 3 to 4 times faster than the wheels. does it vibrate on or off the gas? Can you power through the vibration like go 60 and then coast back through? You have replaced a lot of parts that would not cause vibrations. Are you just changing parts willy nilly or is someone actually checking and verifying that these parts really bad?

Jul 18, 2011 | 2001 Chevrolet Silverado

2 Answers

Replaced U-Joints and had vibration ,had driveshaft balanced and still vibration 45MPH on up. 2000 1500 extend cab 4 4 8'bed 2-piece drive shaft with carrier bearing, any ideals also fan switch speeds 1...


check your tires for a bad spot or a knot. this could cause the vibration. check you switch and see if it has power. if it does maybe the a relay.could also be a lose ground wire.

Sep 17, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

Hard vibrations at 45mph or more


two things would do this that I can think of right now. wheel balance, and or driveshaft balance. I would go get my wheels balanced at a shop first.

Feb 10, 2010 | 1990 Ford F150

1 Answer

Have grand caravan 2001 awd i get to 50 it starts vibrates think it might be carrier bearing after 50 it seems to lessen some no problem in front end what do u think


Most vibrations at speeds from 45mph to 55mph indicate tire balance problems. If there is no vibration outside this range have the tire balance checked. If there is a vibration that starts around 50mph and continues at higher speeds there could be a problem with the CV joint(s).

Nov 05, 2009 | 2001 Dodge Caravan

1 Answer

Bad vibration engine trans under load


seems your problem is within your clutch,defective part,usually a defective release bearing will cause gear shifter and pedal vibration but not as bad as yours,but by pressing on clutch pedal vibration stops,point to clutch!

Apr 07, 2009 | 2002 Dodge Neon

1 Answer

2001 Jeep Cherokee Vibration at highway speeds


That kind of vibration generally can be associated with a binding universal joint. Sometimes you can see a bit of rust around the seals, sometimes not. The "shake" test is generally valid only with vehicle off the ground and trans in neutral, but sometimes the bearings are fused with rust and do not move.If "eyeball" inspection reveals nothing , remove the driveshaft (s) and physically move joints. If overly loose or binding they are bad. If after complete inspection you still come up with nothing then it's time to look at other "oddball" things.
good luck

Dec 27, 2008 | 1996 Jeep Cherokee Country

1 Answer

Vibration at 45 mph.


first, if the milage is high it could be a cv halfshaft even if the boots are not split. if the tires are new and no rims are bent, make sure there is no fix -a- flat in the tires, (liquid will not balance) and cause a severe vibration. i would suggest you take it back to your shop and have them put it on a lift, raise up the front wheels under the outer part of the lower control arm where the front is not hanging down too far and start the vehicle. run it up to 45mph to 60mph and have them feel in the drivetrain for vibrations and shakes.if it is felt with the car this way the vibration is in the drivtrain. inner cv's or in the transmission. thanks and let me know what you find out.

Sep 20, 2008 | 2004 Chevrolet Venture Passanger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...