Question about Cars & Trucks

Open Question

Chevy Malibu 2013 LTz showing code 145 , what does that mean?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3640 Answers

SOURCE: 2000 chevy malibu

po300- could be plug, wire or a bad coil.

Posted on Nov 03, 2009

johnjohn2
  • 5763 Answers

SOURCE: find the themperature sensors in the radiator

heres a picture diagram that shows the switch, this switch is located on the coolant surge tank, hope this helps,95a3698.gif

Posted on Mar 09, 2010

  • 3230 Answers

SOURCE: Change headlight on 2008 Chevy Malibu

Hi there,

Well first you can please follow the below steps -
1. Make sure the ignition key is in the off position and the headlight switch is off. Release the hood latch.
2. Open the hood and locate the top of the headlight assembly where you intend to change the headlight. If a plastic shroud is present, locate the center bolt and remove it with a ratchet and a socket. Lift the shroud out of the way to access the headlight assembly retaining brackets. Some later models may feature a snap-release shroud requiring no tools to remove.
3. Locate the brackets on the top rear of each side of the headlight assembly. Lift them all the way up to align the hole on the bottom of each bracket to the retaining tabs on the assembly.
4. Pull the assembly forward away from the Malibu, but be careful not to scratch the bumper. There are three guide pins that require unseating. The guide pins are what aim the headlights and it may take some wiggling to get the pins from their seats.
5. Support the assembly with one hand and then reach behind the unit with the other. The low beam bulb is on the outside, the high beam bulb is on the inside. You can also replace the parking light if desired. Locate the wire harness connection. Un-clip the wire harness from the back of the bulb socket. Remove the bulb by turning it counterclockwise 1/3 of a turn to align the release tabs of the ring and the assembly. Wiggle the bulb out of the assembly.
6. Place the latex gloves on your hands before opening the package of the replacement bulb. Oil in our skin can damage the glass bulbs of halogen headlights.
7. Carefully insert the new bulb into the ring and then align the tabs of the ring to the tabs of the headlight assembly. Push inward and then twist clockwise 1/3 of a turn to lock the bulb in place. Reattach the wire harness. Rest the headlight assembly inside its cavity and test the operation of the headlight before securing the headlight assembly in place. Be sure to turn the lights and ignition back off.
8. Align the three guide pins to their seats and push the assembly back into them gently until they snap into place. Replace the retaining brackets by pushing them downward to lock into place. Replace shroud, if applicable. Remove the tools and old bulb and close the hood. Post comments for further help or information......

Good Luck!!

Posted on Mar 27, 2010

  • 60 Answers

SOURCE: What are the step by step instructions to change

Find the oil drain plug, remove, drain the oil into a pan, reinstall the drain plug a tighten, locate the oil filter and remove, check mounting surface to make sure the old gasket didn't stick. Coat the new filter gasket with oil and install hand tight. Refill the oil, make sure that you do not overfill. Start enigne for about a minute, shut off and double check the level, and that the filter and drain plug do not leak.
Some engines can be difficult, to identify the location of the drain plug and filter. There are thousands of configurations out there, If you are not familiar or can not locate the plug and filter, take the vehicle to a shop for service.

Posted on Apr 11, 2010

  • 1 Answer

SOURCE: My Power Steering fluid is low, I want to add

they have no place to fill power steering fluid it uses brake fluid and power steering fluid for both systems the electric power steering fluid system is joke if its broke you have to spend 1200$ PLUS TO FIX PROBLEM I HERE LOTS OF PEOPLE HAVING PROBLEM WITH IT WORKING ONE MINUTE NOT THE NEXT UNTIL IT KILLS SOMEONE IT WONT BE FIXED IT SHOULD BE RECALLED AND THENTHE SYSTEM SHOULD NEVER BE USED AGAIN CHEVY KNOWS OF PROBLEM BUT WONT FIX PROBLEM BECAUSE ITS TOO EXPENSIVE SOUNDS JUST LIKE TOYOTA UNTIL THE COST OF LAWSUITS OUTWEIGH THE PAYOUT ON CLAIMS THEY WONT DO NOTHING WE PEOPLE NEED TO FILE SUIT SO PEOPLE DONT DIE BECAUSE OF THE GREED OF BIG COMPANIES TURNING THERE NOSE UP UNTIL SOMETHING OR SOMEONE CHALLENGES THEM IM NOT ASKING NOTHING MORE BUT FIX THE PROBLEM FREE NO MORE NO LESS AND BYE THE WAY EVERYONE IS COMPLAING OF CLUNKING SOUNDS WHEN TURNING DUE TO ANOTHER PROBLEM WITH STEERING SYSTEM NO WONDER PEOPLE DONT BUY AMERICAN CARS ANYMORE

Posted on May 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What the meaning code 4 i have malibu ltz 2013


Code 4 means A/C off due to high temp
Thank you

Feb 14, 2017 | 2013 Chevrolet Malibu

1 Answer

Code 145 on Chevrolet Malibu 2013


. P0145 Oxy Sensor Circ Slow Response (bank1, Sensor 3). Bank one is the side of # 1 plug. Bank 1 sensor 3 is at the outlet of the converter. God_Bless!

Feb 26, 2015 | 2013 Chevrolet Malibu

1 Answer

On the main screen showin code 145 how can i solve it


1st you need a code reader or hand held reader autozone oriellys most all auto parts stores will plug into it and clear the code for u but you have to repair the problem coding or this does no good it will just code again when you turn the key off and on again

May 26, 2014 | Chevrolet Malibu Cars & Trucks

1 Answer

Where is the oil pump on 2007 Chevy Malibu Maxx LTZ


its on the bottom of the engine block, inside the oil pan

Mar 20, 2014 | 2007 Chevrolet Malibu Maxx LTZ Hatchback

1 Answer

What is code 145?


code P0145 is: O2 sensor circuit slow response (bank 1 sensor 3)

Sep 28, 2013 | 2013 Chevrolet Malibu

1 Answer

Malibu 2013 showing code 145 i


Chevy Malibu 2013 ltz showing code 145, what does that mean?

May 23, 2013 | Chevrolet Cars & Trucks

1 Answer

Find the themperature sensors in the radiator for chevy malibu ltz 2007. I need the respective diagram. thanks.


heres a picture diagram that shows the switch, this switch is located on the coolant surge tank, hope this helps,95a3698.gif

Mar 09, 2010 | 2007 Chevrolet Malibu SS Sedan New Cars

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...