Question about Cars & Trucks

Open Question

NEED HELP WITH IGNITION TIMING ON 1999 FORD COURIER 2.4?

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 5341 Answers

SOURCE: 2005 ford courier v6 sohc 4.0lt timing chain set up

Register for free at autozone.com, giving your make, year, and engine size.

They will have the diagrams for your ford, and quite a bit of repair information and procedures. Good luck.

Posted on May 23, 2012

Ad
Sheikhtijani
  • 1284 Answers

SOURCE: Need instructions to replace timing belt on a 1995 diesel ford courier

Hi,
REMOVAL
Disconnect the negative battery cable.
Remove accessory drive belt.
Remove the timing belt cover.
Align the timing mark on the camshaft sprocket with the timing mark on the cylinder head.
Confirm that the timing mark on the crankshaft sprocket is aligned with the timing mark on the oil pump housing.
Loosen the belt tensioner attaching bolt.
Pry the tensioner away from the timing belt and tighten the attaching bolt.
Remove the spark plugs.
Remove the RH engine mount and raise the vehicle.
Remove the splash shield.
Remove the crankshaft damper.
Remove the timing belt.

6_13_2012_3_43_16_pm.gif



INSTALLATION


Note: Do not mix 1/2 round and trapazoidal belt tooth profiles. This can cause premature belt wear, also the belt is meant to run in a dry environment. For maximum belt life, no oil or belt dressing compound should be applied to the timing belt.
Install the timing belt over the sprockets in a counterclockwise direction starting at the crankshaft. Keep the belt span from the crankshaft to the camshaft tight while installing over the remaining sprocket.
Loosen the belt tensioner attaching bolt, allowing the tensioner to snap against the belt.
CAUTION: Do not rotate crankshaft with the spark plugs installed .


Note: Do not turn the engine counterclockwise to line up the timing marks. After rotation, recheck camshaft timing marks for alignment. This will verify that the belt has not skipped a tooth during rotation.
Rotate the crankshaft clockwise two complete revolutions (720 degrees) stopping at top dead center. This will allow the tensioner spring to load the timing belt.
Tighten the belt tensioner attaching bolt to 23-30 Nm (17-22 lb-ft) .
Install the crankshaft damper.
Install the splash shield.
Lower the vehicle.
Install the RH engine mount.
Install the spark plugs.
Install the timing belt cover.
Install the accessory drive belt automatic tensioner.
Install the accessory drive belt.
Connect the negative battery cable.


Thank you.

Posted on Jun 13, 2012

emissionwiz
  • 76649 Answers

SOURCE: ford courier 95 ignition wiring diagram

Fixya doesn't have wiring diagrams. Sorry

Posted on Jun 14, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel gauge wont work on my 2002 ford courier


Most times the sender unit in the tank is faulty. or the float has a leak with fuel in side it . to test the dash gauge remove the cable from the tank unit, turn on the ignition and earth the tank cable , the gauge will move if it is ok.

Mar 18, 2015 | Ford Cars & Trucks

1 Answer

My parents took out my 1993 ford courier engine and dropped it into a 1994 courier I need to know where the wires go on the engine what colour goes where


well bud i would leave it to and expert if you get the rong wire in the rong place you can fry them all it can get expensive but mostly you need the ignition box hoot up and the distributor wires and such make sure you have the correct firing order for the distributor and t fuel lines to go to the engine there are the basics if i was there i could just do it four you hope this helps

Jan 13, 2014 | Cars & Trucks

1 Answer

1999 ford courier car horn


you need test the fuse+horn and adjust the small screw+wires for bad contacts, loose or corroded, relais clean the contacts, voltage of supplier with VOM+button for dirty or faulty. see the diagram and fix it.
God bless youe55973fb-cc53-41eb-9ba9-a58349d1a5da.gif

Jul 10, 2013 | Cars & Trucks

1 Answer

Ford courier 95 ignition wiring diagram


Fixya doesn't have wiring diagrams. Sorry

Jun 14, 2012 | Cars & Trucks

1 Answer

Ford courier van x reg td


Have you checked the heater plug relay?

Nov 26, 2008 | 2000 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...