Question about 1997 Jeep Grand Cherokee

1 Answer

ENGINE SWAP 2001 4.0 IN TO A 1997 jgc LAREDO - 1997 Jeep Grand Cherokee

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

Should work, if it's also a 4.0 that came out. If it was a 4 cylinder then you will need a lot of parts and wiring harness for the swap like 4.0 shocks, motor mounts, transmission, drive shaft etc

Posted on Oct 21, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 jgc starts then stalls


Take it to a properly qualified and licensed mechanic you know and trust.

Nov 10, 2013 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Will a 2001 4.0 engine work in my 1997 JGC Laredo?


most salvage yards have a what years work where manual may check with them like you pull it parts

Oct 21, 2013 | 1997 Jeep Grand Cherokee

1 Answer

Are a 1993 4.0 liter high output 2 wheel drive Jeep Grand Cherokee countries have the same block as a 1990 Jeep Grand Cherokee Laredo 4 wheel drive it also has the 4.0 liter engine but it is not the high...


the first grand cherokee laredo was in 1992 . it was all jeep sports back then, the blocks are all the same .you will need to use some of the sensors from the old motor, the distributor and oil sending unit and temp sensor. will be no problem. if I can put a ford ranger motor in a mercury sable your swap is easier

Dec 05, 2012 | Cars & Trucks

1 Answer

Have a 1999 Jeep grand cherokee what year BCM is compatible? Will a BCM from a 2003 work in a 1999?


I THINK THE VIN IS LEARNED IN THE BCM WHICH MEANS YOU CANNOT USE A USED ONE

Sep 05, 2012 | 1997 Jeep Grand Cherokee

1 Answer

My 1996 JGC laredo died in the left hand turn lane of two major intersections. Tried to restart it - it acted like it tried to turn over and nothing. After it sat for about 30 min. with the flashers on -...


I would check to see if it has spark when it does this next time. Then if it don't I would start by changing the pickup coil. If not that then i would try the crank sensor. hope this helps good luck

Nov 21, 2010 | 1996 Jeep Grand Cherokee

1 Answer

I have a 2005 jgc laredo 4x4 3.7L The headlamps flash at random and when this happens the dash lights also flicker????


You have a problem with the ignition switch. The switch has been redesigned for that model. It shorts out for a split second your car is acually stalling out for a split second. Seen this alot have the ignition switch replace and your problem is solved if u need info on how to install I will walk u through it. Hope this help please rate.

Aug 02, 2009 | 2005 Jeep Grand Cherokee

1 Answer

95 jgc laredo spitting and sputtering , will not idle dies


You may want to check the Idle Air Control Valve (IAC). It is located on the back of the throttle body and very easy to change. You may have some luck just cleaning to see if it makes a difference and then you can buy a new one.

May 30, 2009 | 1995 Jeep Grand Cherokee

4 Answers

Rear end (axle)


call jeep and give them last 9 digits of your vin and ask for three things -Differential Type,Gear ratio, and Track lock- They will give you
1) Dana 35 or 44
2) Gear Ratio 3.31 or 3.73
3) Track Lock - yes/no

Jan 11, 2009 | 1998 Jeep Grand Cherokee

1 Answer

Transmission won't shift out of 1st gear


the output spped sensor is on the drivers side rear of the transmission case..its a 2 wire connector..the wires are dark bluewith a black tracer and light green with a white tracer

Sep 30, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
1997 Jeep Grand Cherokee Logo

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...