Question about Cars & Trucks

1 Answer

I am having trouble adjusting my New Idea corn picker/sheller to get all the corn off the cobs. Please help!!!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 401 Answers

If you have enough money, either hire farmhands or rent/buy a combine.

Posted on Oct 21, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ive got soot trouble. need to adjust air-fuel mixture. the underside of the unit is exposed in garage. how do i clean and adjust oxygen/ fuel mixture?


Having no idea what your unit is . seems to be a problem for us to help you solve . but know it is not a car or truck

Feb 13, 2016 | Cars & Trucks

2 Answers

What do i need to replace the motor in a 1998 chevy cavalier


Floor jack, jack stands, cherry picker, common sense, mechanical ability, basic hand tools, service manual helps.

Jun 08, 2015 | Cars & Trucks

1 Answer

How do I replace the motor mounts on my 2001 Toyota Camry Solora xle v6


Ok, first off apply E brake. Second, locate motor mounts usually on side bottom, connect to frame. Third jack up car place jack stands. Fourth,disconnect all wiring, maf, pretty much anything and everything that will get in way. Fifth, grab cherry picker, connect engine to cherry picker. Sixth, disconnect engine from trans, or leave connected but might be more difficult for some. Seventh,unbolt engine from mounts(usually 3or so bolts on each mount), do not rock engine, raise cherry picker(or crane some call it different)when tension on chain slowly rock engine. Should pop out unless you missed a bolt.

Feb 20, 2015 | 2001 Toyota Camry Solara

1 Answer

Broken water pump bolts


You need to take off trans mounts also either that or dissconnect trans, I'd go with the first option and either jack it up or use a cherry picker to raise it. I suppose you could lower with a jack or picker also if distance is less.

Nov 01, 2012 | 1996 Chrysler Town & Country

1 Answer

WHAT TO DO with code 18 on order picker toyota 6BPU15


Its the dead man switch out of adjustment. Showing closed at start up. Hope that helps

Jun 20, 2012 | Cars & Trucks

1 Answer

My windshield wipers were stuck in the on position for months and the only way to make it stop was to pull the fuse, so I bought a used steering column and put the old one in the front yard ( garbage...


Well,,,,, the first proble i would say is your wiper delay unit or a fulty relay.. the next proble, well,,,,, check back over your work, seems like your ignitionswitch is out of adjustment/alignment or your wire harnes connector needs to be reseated.. alot depends on what kind/make/year your car/truck is.. this info is very wide scoped. good luck!

Sep 13, 2011 | Buick LeSabre Cars & Trucks

3 Answers

I was told the clutch on my 2003 mazda protege is hydrolic....how do I go about adjusting it


The whole idea behind the Hydralic Clutch is there is no adjustment.If the clutch is slipping then you need a new one.If you are having trouble getting it into gear then you may have a bad clutch master and or slave cylinder.Let me know if i can help.

Feb 06, 2011 | Mazda Protege Cars & Trucks

1 Answer

Some of the rocker arms are chattering on my 1995 pathfinder SE 3.0liter V6 4X4 i need to know exact specifications on tightening them back! PLEASE HELP!


Hi,

This engine and vehicle are fitted with hydraulic valve adjusters which means there is no clearance adjustments for them.
The trouble will be the lifters are either worn or have a blocked lubricating orifice.

Give it an engine flush and put in some new engine oil, this may help you out.

Thanks

Jason

Oct 05, 2010 | 1995 Nissan Pathfinder

1 Answer

I'm having trouble with my horn. It won't stop


HI
Please check this link to have an in-depth idea regarding your query.
http://car.tips.net/Pages/T004714_Your_Car_Horn_wont_Stop_Blowing.html
Let us know if you want something more, else please accept the suggestion.
Thanks for contacting fixya.com

Mar 24, 2010 | 1998 Mitsubishi Montero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...