Question about 1992 Mazda B-Series
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Torque on 1994 Mazda pick up
if its a four cylinder(lets hope)the specs are 80-90ft.lbs torque.if its a six cylinder it is 14ft.lbs torqueat 90 degree intervals then repeat until correct torque has been reached.bad news is you can not use the same bolts on the six cylinder engine.have to be new to keep from breaking them
Posted on Mar 15, 2009
Remember you have pre loaded cam gear's that have to be loaded, or it will make kinda of a lifter noise but not lifter's.
step #1 17-19 ft.lbs
step #2 additional 85-95 deg
Posted on Nov 19, 2009
Tips for a great answer:
Nov 24, 2014 | Mazda MAZDA3 Cars & Trucks
Mar 25, 2013 | Cars & Trucks
Feb 16, 2012 | Mazda 323 Cars & Trucks
Jan 07, 2012 | Cars & Trucks
Jul 05, 2011 | 1994 Mazda Protege
Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.
Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.
B2500 4 Cylinder
Torque sequence: --------- ' 10 6 2 4 8
' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51
Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final
tighten all bolts an additional 90 to 100 degrees recheck final
torque in sequence *** CAUTION ***engine uses Torque To Yield head
bolts (TTY) that permanently stretch during the initial installation.
New head bolts must be used when cylinder head is replaced or
re-installed to obtain proper torque.
B3000 3.0 6 Cylinder
Torque sequence ---------- ' 6 4 2 8 '
' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen
in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque
to 73 Ft/Lbs
B4000 4.0 6 Cylinder
Torque sequence --------- ' 5 1 3 7 ' '
' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in
sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs
Step 3: turn cylinder head bolts in sequence an additional 90-degrees
recheck final torque in sequence *** CAUTION ***engine uses Torque To
Yield head bolts (TTY) that permanently stretch during the initial
installation. New head bolts must be used when cylinder head is
replaced or re-installed to obtain proper torque.
Good luck with this job!
Feb 06, 2011 | 1998 Mazda Pickup
Nov 19, 2009 | 1994 Mazda 323
Sep 17, 2009 | 1994 Mazda 2WD B Series Pickup
Jul 24, 2008 | 1994 Mazda 2WD B Series Pickup
Mar 22, 2012 | 1992 Mazda B-Series
221 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: