Question about 1992 Ford Explorer

1 Answer

1992 ford explorer as soon as i turn the key the RPM's go straight up to 3,000 or more. It happens with just the key on and when you start the engine. Also when driving it sounds like it's revving way too high in all the gears 1-2-D and when you first go into OD it revs high for a minute until finally leveling out and driving smooth.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 162 Answers

Check your throttle cable to make sure it's not binding at all, make sure its free. Try cleaning your throttle body and look at your tps.

Posted on Oct 20, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76132 Answers

SOURCE: OD off Light Flashing on my 1998 Ford Explorer XLT 4.0 V

The OD light is flashing to alert u to the fact that some kind of fault has occured in the transmission, the problem is in many cases a slipping condition, you need to have the trans control system tested for the trouble codes that are stored when this light flashes, this will let u know what the problem is and a direction to follow to repair it.

Posted on May 26, 2009

  • 14036 Answers

SOURCE: 1998 Ford Taurus Station Wagon SE

CODE P500 VSS NO SIGNAL.PROBLEM COULD BE CONNECTOR TO VSS IS SHORTED OR THE MAGNET GEAR ON TRANSMISSION DRIVE SHAFT COULD BE BROKEN OR MISSING TEETH.

Posted on Aug 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Ford Explorer will not start


What happens when you turn the key to start the vehicle ? Does the starter spin the engine ? Crank - no start condition ! Or does nothing happen when you turn the key to the start position ? NO - CRANK - NO START condition ! Two totally different diagnostic procedures.
So will not start how ?

Aug 05, 2016 | 2004 Ford Explorer

1 Answer

1992 toyota 22re fluids out and puts out a lot of fume out the exhast


Floods out.Multiple causes.How does it run when warmed up?Still stink?
Check injectors: Run the engine up to 3,000 RPM and turn off the key,while flooring the gas pedal.If engine still runs,the injector(s) are stuck open.
Also check for a vacuum leak-that will cause the engine to run very rich.
Also may be an open circuit in the temp sensor(computer side).The engine may think it's very cold and richen up the mixture.

Mar 07, 2013 | 1992 Toyota Pickup

1 Answer

I have a 1992 ford explorer. It stoped and i can't get it to run


The inertia switch that you are looking for is underneath the passenger floorboard carpeting, on the firewall.

Jan 11, 2010 | 1992 Ford Explorer

1 Answer

How to replace a lock cylinder on a 1992 ford explorer


Steps to remove and replace the lock cylinder To Remove the Lock Cylinder 1: Remove the cover UPPER/LOWER) from the steering column(usually 2 phillips screws in lower cover, directly behind the steering wheel. 2: Turn the key to the run position (the position before start). 3: Using a small diameter object (paper clip) slide the wire into the hole located underneath the ignition switch on the underside of the column. While pushing up on the pin in the hole, turn the key and pull outward. The tumbler should release and come out. 4: To replace, turn the key in the new cylinder to run. 6: Place the cylinder in the column where the old one came out. 7: Turn the key to the off position and the cylinder is now locked in place.

Nov 17, 2009 | 1992 Ford Explorer

1 Answer

JUST PUT NEW HEADS ON MY 92 FORD EXPLORER AND NOW I WHEN I TURN THE IGNITION SWITCH NOTHING HAPPENS GAUGES DO NOT MOVE AND STARTER DOES NOTHING WHATS WRONG


make sure battery is fully charged, if it is check all your connections positive and negitive, start there,good luck.

Oct 29, 2009 | 1992 Ford Explorer

1 Answer

Replaceing a lock cylinder in a ford explorer with no keys.


The least damage would be caused by a locksmith. You could break more than the lock cylinder if you try to drill it out yourself.

Jun 21, 2009 | 1992 Ford Explorer

1 Answer

It wont start


Please don't forget to rate if feel this helped you out or when you do find out the problem, please rate the comments posted. Thanks. It helps us help you more!

Greg

May 21, 2009 | 1992 Ford Explorer

1 Answer

1992 ford explorer


A bad battery. it does not have enough voltage to operate ingine plus excite alternaor. probably has a bad cell, is your battery holdown tight? bouncing batteries do not last

Oct 05, 2008 | 1992 Ford Explorer

Not finding what you are looking for?
1992 Ford Explorer Logo

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...