Question about Nissan Pickup

1 Answer

Nissan Clutch Problems

Loud squeek when clutch peddle is depressed d22 import pick up 2005?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 2,760 Answers

If this has original clutch this noise is a warning that it's time for a change

when doing this job make sure the clutch /throwout bearing/pressure plate and slave cylinder are all done at same time will save you money in the long run allthought being a bit expensive at first

Posted on Oct 20, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: loud squealing noise when clutch pedal is depressed

Hi Dom,
Probably the release bearing is worn-out.
In my opinion, you should look for good motor shop around your area.
Let them replace the release bearing, clutch lining assembly, and the pressure plate assembly.
Labor cost for that job is around 500.00 to 800.00 pesos.
I don't know the prices of the parts now.

I'm sure this will solve your problem.

eloysky

Posted on Feb 16, 2009

  • 6 Answers

SOURCE: 2001 nissan maxima clutch problems

If the pedal is sticking to the floor at times and you seem to be losing pressure then it would have to be the clutch master cylinder causing the problem.

Posted on Jun 12, 2009

duane_wong
  • 6826 Answers

SOURCE: clutch problems

Check fluid level of hydraulic clutch that would cause this condition if low in fluid or not bled of air.

Posted on Jul 08, 2010

alicantecoli
  • 22156 Answers

SOURCE: I own a 1993 Nissan

No sorry to be the bearer of bad news but i think the fingers on the clutch are worn to excess and when the clutch is depressed fully the bearing is going through the fingers of the clutch causing the noise you can hear .Eventualy it will need a new clutch which is not expensive if you do it yourself

Posted on Jan 23, 2011

Testimonial: "Thanks 4 your speedy responce The clutch master pushrod should have an adjustment. Do you think this could solve the problem"

Bruce Boogie
  • 242 Answers

SOURCE: hard to get in gear whining noise when clutch

Get it to a garage - if the clutch has worn out - 9 years old and its quite possible - you don't want to have to have a new gearbox as well.

Cars cost!!

GOOD LUCK

Posted on Mar 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nissan D22 3.0L diesel 4x4 - clutch shudder.


The most common cause of clutch judder when releasing to pull away is oil on the plates. That can be caused by main bearing seals failing.

Apr 19, 2017 | Nissan Cars & Trucks

1 Answer

1988 Nissan 300zx 5 speed clutch peddle does not


Sounds like you have a leak in your clutch master or slave cylinder. I had the same problem. They are not too expensive at kragen or auto zone. The master cylinder is located on the right side of your engine closest to the driver. Open the cap and check if theres fluid. If its low or empty then there might be a leak. The slave cylinder is located on the passenger side under the car bolted to the transmission. That could be leaking or not working properly. I would replace both if you can. Hope this helps.

Sep 24, 2011 | 1988 Nissan 300ZX

1 Answer

Me and a mate have been trying to bleed my clutch on my 80 series for 5 hrs and carnt get anywhere. What the hell am I doing wrong? I can do everythingt else other then 1 of the simplist job


Just follow the procedure in the right order. Fill the clutch reservoir on the master cylinder to the max and leave the lid loose. Fit a transparent plastic pipe on the bleed nipple on the clutch slave cylinder bleed nipple. Put the other end of the pipe into a jar to catch the waste fluid. Put some thick grease around the base threads of the bleed nipple, this stops air being sucked in via the threads whne the nipple is slackened off. Loosen the bleed nipple by 1/3 of a turn. Have your mate slowly depress the clutch peddle. When he has reached maximum travel have him hold it there while you turn the bleed nipple a third turn back to tight. Have your mate release the clutch peddle, clutch fluid from the master reservoir should now fill the the master cylinder. Have you mate press the peddle a quarter way and then release the bleed nipple a 1/3 of a turn. Have your mate depress the clutch peddle all the way to maximum travel. Again tighten off the bleed nipple before releasing the clutch peddle. Keep doing this process until no more air bubbles can be seen in the fluid in the pipe attached to the bled nipple. Every four cycles or so check on the fluid level in the master reservoir and keep topped up with fresh fluid. When everything completed tighten the bleed nipple, it is not necessary to tighten the hell out of it as at some point you may need to do this again. Wipe everything down pump the clutch peddle a few times to be sure of correct operation and no leaks.

Jul 01, 2011 | 1991 Toyota Land Cruiser

1 Answer

The clutch peddle went to the floor when i pushed the clutch peddle in


Check the floor by the clutch peddle if it is wet (you may need to look at the very top of the peddle)than you problem is the clutch mastercylinder

Jan 31, 2011 | 1994 Nissan Pickup

2 Answers

I own a 1993 Nissan Pathfinder 5 speed. Yesterday I went to start my truck so I depressed the clutch peddle all the way so I can start the truck and in maybe the last inch of travel I heard a grinding...


No sorry to be the bearer of bad news but i think the fingers on the clutch are worn to excess and when the clutch is depressed fully the bearing is going through the fingers of the clutch causing the noise you can hear .Eventualy it will need a new clutch which is not expensive if you do it yourself

Jan 23, 2011 | 1993 Nissan Pathfinder

1 Answer

'05 Frontier w/ 6-speed manual transmission. Push the clutch straight in and truck will not start. Push the clutch in and hard to the left the truck will start just fine. No problems with starter,...


It's called the clutch switch and it's supposed to only allow current to the starter when the clutch pedal is depressed all the way down, releasing the clutch. It's bolted in front of the clutch pedal. Yours must be bad or shifted to the left somehow. Have it checked, then repositioned or replaced.

Nov 04, 2010 | 2005 Nissan Frontier

1 Answer

1987 Nissan PU, I replaced the master and slave clutch cyls. I bleed the system and there is no air in the lines but peddle does not get hard. Could the new master or slave cyl be bad? I see you can adjust...


The shaft should come all the way back, when the pedal is back, the master shaft should be adjusted so there is very little play in the pedal. But it needs some play. Make sure you can see the slave cylinder move when you depress the clutch pedal, you will need help to operate the pedal, while you look.

May 10, 2010 | 1987 Nissan Pickup

1 Answer

Gear shifting


Adust clutch cable.Test...start the car in first gear with clutch fully depressed, parking break off. Slowly release the clutch. determine when the vehicle starts to move. If clutch is fully depressed call that 100%, fully released is 0%. The vehicle should be moving at around the 55-45% range.

Dec 02, 2009 | 2002 Nissan Xterra

2 Answers

2001 nissan maxima clutch problems


check the mechanical leakage at the clutch housing for binding and wear.

Jun 12, 2009 | 2001 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...