Question about 1988 Nissan Maxima

1 Answer

Reverse lights wiring diagram

Reverse lights not working

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

On a 1988 I would replace or clean the leads that the bulbs connect to with baking soda /water solution and wire brush.

Posted on Oct 20, 2013

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 28 Answers

SOURCE: i have a 1989 ford F150 xlt and my reverse lighta dont work

ok i understand now the easiest thing for you to do is just get something to connect the two wires together,( like a short piece of wire ) bypassing the switch. have someone watch the reverse lights while you do this. if the lights come on then you need a switch. if not you have a bad wire or fuse/ fusible link. you can use a test light to see if you have power to the switch, one wire should have power and the other leads to the reverse lights. you can test the switch itself with a ohm meter, or continuity tester aswell if you have one. if you need more help i am here for you... dustang

Posted on May 12, 2009

  • 1986 Answers

SOURCE: 2005 Pathfinder no reverse lights

On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced

Posted on Oct 01, 2009

SOURCE: 2001 nissan exalta sta/sentra (released in the

Locate the fuse box underneath the drivers side steering wheel and remove the cover lid. Underneath the lid is a diagram of what each fuse controls. Locate the "Stop Lamp" and "Taillight" fuses and pull them out and check them with a fuse test light (avalible at your local auto parts store) Replace the burned out fuse with the same number fuse (the amp number is located on top of the fuse) and your lights will work again

Posted on Sep 21, 2010

  • 1026 Answers

SOURCE: why do my reverse lights stay on??

has to be switch normally on gearlever or

Posted on Nov 02, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gx470 2006 reverse light always on


Check the wiring diagram for a reverse light switch (located on the trans usually) Most common cause

Mar 20, 2017 | 2006 Lexus Gx 470

1 Answer

I have a 2006 Chevy Uplander and I'm trying to connect a reverse backup camera to my car and I do not know which wire is positive for the reverse light bulb


open up the rear bulb compartment cover
and note the color wires running into the reverse light bulb holder

a hand full of fuses as you
use a LED test light or voltmeter to find the right wire

and use those color wires as your power /earth for the reverse camera

or you need the rear loom wiring diagram for that 2006 chev

Oct 13, 2016 | Cars & Trucks

1 Answer

Seat Ibiza 1.2 12v 2004 My Reverse Light doesnt work :( Any help much appreciated!


Take it to someone who knows how to fix these thing's !!!!! Before you mess it up !

May 16, 2015 | Seat Ibiza Cars & Trucks

1 Answer

My reverse lights stay on all the time. Mitsubishi galant 2002


Get a wiring diagram and work through it. Be mindful of the grounds as well.

Jan 12, 2015 | 2002 Mitsubishi Galant

2 Answers

2003 altima dash fuse blows when i put in reverse and alternator stops working


It is electrical, could be initiated by mechanical (shift lever mechanics are pinching a wire in reverse) or a shorted wire or solenoid in the reverse light system or transmission solenoid circuit. Need a detailed wiring diagram to determine path of circuit for that fuse. That is where you need to start. Try your local library or dealer for a service manual. Look Online also.

Nov 02, 2013 | Cars & Trucks

2 Answers

1992 honda integra horn fuse blows after applying brakes


Honda makes the Integra but it uses the Acura name in the US.
According to the wiring diagram the brake lights and horn are on the same circuit. So I would check the bulbs and sockets for a short.
The brake light switch also involves the cruise control system.

Sep 21, 2012 | Cars & Trucks

1 Answer

1988 sierra 1500 backup lights don't work. Need


actually it is very basic check the associated fuse if good go to the reverse nuetral saftey switch you should see power on a wire and when you go into reverse you will see power on two wires....let me know

Aug 31, 2009 | 1998 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...