Question about Cars & Trucks

1 Answer

No converter lock up after ignition switch was replaced

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 46 Answers

What year, make, model?

Posted on Oct 20, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the torque converter clutch solenoid located P0744


troubleshooting?
  • cvt re0f10a
p0744 torque converter

description
this malfunction is detected when the torque converter clutch does not lock-up as instructed by the tcm. this is not only caused by electrical malfunction (circuits open or shorted), but also by mechanical malfunction such as control valve sticking, improper solenoid valve operation, etc.

dtc logic

dtc detection logic
159975295

dtc confirmation procedure

caution:
always drive vehicle at a safe speed.

note:
if "dtc confirmation procedure" has been previously performed, always turn ignition switch off.
then wait at least 10 seconds before performing the next test.
1.check dtc detection
with consult-iii
  1. turn ignition switch on.
  2. select "data monitor".
  3. start engine and maintain the following condition for at least 30 seconds.
159894994

with gst
follow the procedure "with consult-iii".
is "p0744" detected?
yes - go to see: cvt re0f10a.
no - check intermittent incident. refer to see: testing and inspection\initial inspection and diagnostic overview\intermittent incident.

diagnosis procedure
1.check line pressure
perform line pressure test. refer to see: transmission and drivetrain\continuously variable transmission/transaxle\testing and inspection\initial inspection and diagnostic overview\cvt re0f10a.
is the inspection result normal?
yes - go to 2.
no - repair or replace damaged parts.
2.check torque converter clutch solenoid valve
  1. turn ignition switch off.
  2. disconnect cvt unit connector.
  3. check torque converter clutch solenoid valve. refer to see: cvt re0f10a. is the inspection result normal?
yes - go to 3.
no - repair or replace damaged parts.
3.check lock-up select solenoid valve
check lock-up select solenoid valve. refer to see: cvt re0f10a.
is the inspection result normal?
yes - go to 4.
no - replace transaxle assembly. refer to see: transmission and drivetrain\continuously variable transmission/transaxle\service and repair\removal and replacement\cvt re0f10a\transaxle assembly\exploded view.
4.check secondary speed sensor system
check secondary speed sensor system. refer to see: p0720\cvt re0f10a.
is the inspection result normal?
yes - go to 5.
no - repair or replace damaged parts.
5.check primary speed sensor system
check primary speed sensor system. refer to see: p0715\cvt re0f10a.
is the inspection result normal?
yes - go to 6.
no - repair or replace damaged parts.
6.detect malfunctioning items
check tcm connector pin terminals for damage or loose connection with harness connector.
is the inspection result normal?
yes - replace tcm. refer to see: powertrain management\transmission control systems\control module, cvt\service and repair\cvt re0f10a\exploded view.
no - repair or replace damaged parts.

component inspection (torque converter clutch solenoid valve)
1.check torque converter clutch solenoid valve
159962448

check resistance between cvt unit terminal 12 and ground.

159975296

is the inspection result normal?
yes - inspection end
no - perform "self-diag results" mode for "transmission".

component inspection (lock-up select solenoid valve)
1.check lock-up select solenoid valve

159962449

check resistance between cvt unit terminal 13 and ground.

159975297

is the inspection result normal?
yes - inspection end
no - replace transaxle assembly. refer to see: transmission and drivetrain\continuously variable transmission/transaxle\service and repair\removal and replacement\cvt re0f10a\transaxle assembly\exploded view.

Jan 21, 2015 | 2010 Nissan Altima 2.5

1 Answer

Relay switch


Ignition and Start Switch Replacement
Removal Procedure
2c23f8d.jpg Disconnect the battery ground cable. .
Remove the steering column filler panel.
Remove the knee bolster bracket.
Remove the instrument panel (I/P) cluster trim panel.
Remove the ignition switch bolts.
Lower the ignition switch away from the instrument carrier.
Insert the key into the ignition lock cylinder. Turn the key to the ON/RUN position.
Depress the transaxle park/lock cable retainer to release. Pull to remove the park/lock cable from the ignition switch.
Important: The Passlock? electrical connector cannot be removed until the lock cylinder is removed.

Depress and hold the detent on the bottom of the ignition switch in order to release the ignition lock cylinder. Remove the ignition lock cylinder with the key.
d857e46.jpg Disconnect the Passlock? electrical connector.
Disconnect the electrical connectors.
4093e3a.jpg Important: Ignition switch lock cylinder that won't rotate or is seized.

Perform the following procedure if the ignition switch lock cylinder is seized or won't rotate.
12.1. Protect the immediate work area with suitable material such as clean shop towels or a clean fender cover.

12.2. Locate the surface for the ignition switch lock cylinder release button (2) on the plastic ignition switch housing and center punch a location (1) on the "rib" approximately 3/8 inch reward (toward the key entry end) from the cylinder release button.

12.3. Carefully drill a hole through the plastic housing with a 1/8 inch drill bit.

12.4. Carefully drill a larger hole at the pilot location, and slightly into the ignition switch lock cylinder surface to break the release button retaining spring using a 9/32 inch drill bit.

12.5. Remove portions of the broken spring from the hole using a small suitable tool.

12.6. Grasp the ignition switch lock cylinder and remove it from the switch housing.

12.7. Remove any plastic "flash" from the drilling operation, and using compressed air blow out the ignition switch assembly.

12.8. Follow service manual procedures when cylinder cording is required. Refer to Key and Lock Cylinder Coding in General Information.

Installation Procedure
If the lock cylinder would not rotate or was seized, perform the following procedure:
1.1. Install the new ignition switch lock cylinder as required by rotating both the cylinder and the ignition switch to the ON position.

1.2. Push the ignition switch lock cylinder into the ignition switch housing until fully seated.

1.3. You may have to slightly depress the release button as the button passes by the 9/32-in hole previously drilled in the ignition switch housing.
9600af8.jpg Connect the electrical connectors.
Connect the Passlock? electrical connector.
Connect the park/lock cable to the ignition switchdd765ba.jpg Turn the key to the ON/RUN position. Install the ignition lock cylinder into the ignition switch. If you turned the key slightly while removing the lock cylinder, you may have to align the white colored ignition switch rotor (1) with the lock cylinder (2). You can rotate the ignition switch rotor (1) with your finger.
Remove the key
681874a.jpg Position the ignition switch to the instrument carrier.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Install the ignition switch bolts.
Tighten

Tighten the bolts to 10 N?m (89 lb in).

Install the trim plate bezel to the I/P cluster. Refer to Trim Plate Bezel Replacement - Instrument Panel (I/P) Cluster .
Install the knee bolster bracket. Refer to Bracket Replacement - Knee Bolster .
Install the steering column filler panel. Refer to Steering Column Filler Replacement .
Connect the battery ground cable. Refer to Battery Negative Cable Disconnect and Connect Procedure in Engine Electrical.

Dec 05, 2013 | 2005 Chevrolet Impala

1 Answer

I was rolling down a window when all of a sudden the follow 4 things STOPPED WORKING and haven't worked since: - All power windows - Heater blower - Horn - Wipers All of the relays I've found seem in tact...


Is the car a convertible? If so the window controls operate through the convertible top computer.
By ignition switch module are you talking about the part under the lock cylinder? They do fail a lot.
What do you mean by the relays are intact? Have you checked for power at each fuse with the key on?

Apr 12, 2011 | 1997 Saab 900

1 Answer

Remove ignition lock to switch link 1995 suburban


The ignition lock assembly contains two components: a lock cylinder to deter theft and an electrical portion that supplies power to electrical components such as the radio, electric windows, and windshield wipers. The electrical portion of the ignition switch also provides power to the starter motor to start the engine.
The ignition lock is an anti-theft device that prevents a vehicle from being driven unless the ignition key is in the ignition switch. If the ignition key is not in the ignition switch, it 's impossible to turn the steering wheel.
To replace the ignition switch cylinder lock, the trim panels around the steering wheel are removed. Then the tamper-proof hardware that attaches the ignition lock assembly to the steering column is removed. The ignition lock assembly is removed from the steering column, and the lock cylinder is replaced. The new ignition lock is reattached to the steering column, and the trim panels are replaced.make sure you dissconect battery first the 1997 had a recall on the ignition switch dont no if the 1995 had a recall if so they will replace for free

Dec 08, 2010 | 1995 GMC Suburban

1 Answer

After battery replacement keyless entry stop working


Synchronization
When
Key buttons operated repeatedly while vehicle out of range and system becomes inoperative. Key batteries replaced.
How - early models
Depress lock or unlock button. Manually lock and unlock driver's door within 30 seconds. System should operate normally after approximately 1 minute. If not, carry out programming procedure.
How - late models
If vehicle locked, manually unlock driver's door using key. Press key unlock button once. Switch ignition ON and OFF. Remove key from ignition switch. Press key lock or unlock button once. System should now operate correctly.

Jun 24, 2010 | 2007 Audi A4 Convertible

2 Answers

Ignition


the actuator inside the sterring column that the lock cylinder turns is boken, this is a very complex job and is not for the home tech without a factory service manual.

Apr 21, 2010 | 1996 Ford Taurus

1 Answer

How do you change an ignition switch on a 2002 VW beetle


This is for the requested item:

Removal & Installation
  1. If necessary, make sure you have the radio code.
  2. Place the steering wheel in the center (wheels straight ahead) position.
  3. Disarm the SRS system, as outlined in the Chassis Electrical System.
  4. Make sure the negative battery cable is disconnected.
  5. Remove the steering wheel, as outlined in this section.
  6. Remove the upper and lower steering column switch trim. Refer to the Turn Signal (Combination) Switch or Multi-function switch procedure for details.
  7. Disconnect the multi-pin connector from the ignition/starter switch.
  8. Remove the locking fluid (paint) from threaded holes of screws.
  9. Loosen the two screws slightly, and pull ignition/starter switch out from steering lock housing in direction shown.

d997782.gif
Remove the locking fluid (paint) from threaded holes of the screws (A). Loosen the two screws (A) slightly, then pull the ignition/starter switch out from steering lock housing in direction of the arrow


To install:
  1. Push the ignition/starter switch into steering lock housing.

    NOTE When installing the ignition/starter lock switch ensure that the ignition/starter lock switch and the lock cylinder are in the same position, e.g. "ignition on".

  2. Tighten screws and seal securing holes with sealant D2.
  3. Connect multi-pin connector to ignition/starter switch.
  4. Install steering column switches, steering wheel trim and steering wheel, as outlined in this section.

Mar 06, 2010 | 2003 Volkswagen New Beetle Convertible

1 Answer

How do i replace the ignition switch in my 94 couger


Removal & Installation
  1. Disconnect the negative battery cable. Remove the upper steering column shroud by removing the self-tapping screws.
  2. Unfasten the four bolts retaining the lower steering column shroud, then remove the shroud.
  3. Remove the lock screw, and detach the ignition switch electrical connector.
  4. Rotate the ignition switch lock cylinder to the RUN position.
  5. Remove the two screws retaining the ignition switch, and disengage the ignition switch from the actuator.
To install:

NOTE A new replacement switch will be set in the RUN position as received.

  1. Adjust the ignition switch by sliding the carrier to the ignition switch run position.
  2. Check to make sure the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock approximately 90 degrees from the LOCK position.
  3. Install the ignition switch assembly into the column actuator hole. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  4. Install the retaining screws and tighten to 53–71 inch lbs. (6–8 Nm).
  5. Attach the electrical connector to the ignition switch. Tighten the lock screw to 7–11.5 inch lbs. (0.8–1.3 Nm).
  6. Connect the negative battery cable. Check the ignition switch for proper function, including the START and ACC positions. Also, make sure the column is in the LOCK position.
  7. Install the upper and lower steering column steering shrouds.

Feb 10, 2010 | 1994 Mercury Cougar

1 Answer

I need to replace an ignition switch on my 1999 Chrysler Sebring convertible, how do I remove the dashboard


This is for the ignition switch like you are asking for:

Ignition Switch REMOVAL & INSTALLATION Cirrus, Stratus, Sebring Convertible and Breeze CAUTION
The Supplemental Inflatable Restraint (SIR) system must be disarmed before working around the steering column. Failure to do so may cause accidental deployment of the air bags, resulting in unnecessary SIR system repairs and/or personal injury.
  1. Disarm the air bag system, as described in Section 6.
  2. Remove the left end instrument panel cover/fuse panel and remove the retaining screw holding the end of the instrument panel top cover.
  3. Remove the instrument panel center bezel.
  4. Remove the screws that secure the instrument panel top cover to the center of the instrument panel.
  5. Lift the instrument panel top cover enough to gain access to the knee bolster attaching screws.
  6. Remove the lower knee bolster attaching screws and knee bolster from the vehicle.
  7. Remove the lower steering column cover attaching screws. Pull down on the lower cover to clear the ignition key cylinder and key release (if equipped).
  8. Remove the lower steering column cover, sliding the cover forward while holding down the steering wheel tilt lever.
  9. Tilt the steering wheel down to the fully lowered position and remove the upper steering column cover.
  10. Remove the screws that hold the combination switch to the ignition lock housing.
  11. Place the ignition lock cylinder in the RUN position.
  12. Insert a small prying tool into the hole in the lower cover and depress the cylinder release tab.
  13. Remove the ignition lock cylinder from the steering column.
  14. Unfasten the electrical connectors from the switch.
  15. Using a No. 10 Torx® bit, remove the ignition switch mounting screw.
  16. Depress the retaining tabs and remove the switch. To install:
  17. Place the ignition switch in the RUN position. Be sure the actuator shaft in the lock housing is also in the RUN position.
  18. Install the switch, making sure the switch snaps over the retaining tabs.
  19. Install the retaining screw.
  20. Connect the wiring to the ignition switch.
  21. Install the ignition lock cylinder.
  22. Install the 2 combination switch mounting screws.
  23. Install the lower and upper shrouds.
  24. Install the knee bolster to the lower dashboard panel and tighten the lower knee bolster attaching screws.
  25. Install the screws that secure the instrument panel top cover to the center of the instrument panel.
  26. Install the instrument panel center bezel.
  27. Install and tighten the screw holding the end of the instrument panel top cover. Install the left side instrument panel/fuse panel cover.
More coming.....

Jun 26, 2009 | 1999 Chrysler Sebring

3 Answers

2005 chevy impala ignition switch


Ignition and Start Switch Replacement
Removal Procedure
2c23f8d.jpg Disconnect the battery ground cable. Refer to Battery Negative Cable Disconnect and Connect Procedure in Engine Electrical.
Remove the steering column filler panel. Refer to Steering Column Filler Replacement .
Remove the knee bolster bracket. Refer to Bracket Replacement - Knee Bolster .
Remove the instrument panel (I/P) cluster trim panel. Refer to Trim Plate Bezel Replacement - Instrument Panel (I/P) Cluster .
Remove the ignition switch bolts.
Lower the ignition switch away from the instrument carrier.
Insert the key into the ignition lock cylinder. Turn the key to the ON/RUN position.
Depress the transaxle park/lock cable retainer to release. Pull to remove the park/lock cable from the ignition switch.
Important: The Passlock? electrical connector cannot be removed until the lock cylinder is removed.

Depress and hold the detent on the bottom of the ignition switch in order to release the ignition lock cylinder. Remove the ignition lock cylinder with the key.
d857e46.jpg Disconnect the Passlock? electrical connector.
Disconnect the electrical connectors.
4093e3a.jpg Important: Ignition switch lock cylinder that won't rotate or is seized.

Perform the following procedure if the ignition switch lock cylinder is seized or won't rotate.
12.1. Protect the immediate work area with suitable material such as clean shop towels or a clean fender cover.

12.2. Locate the surface for the ignition switch lock cylinder release button (2) on the plastic ignition switch housing and center punch a location (1) on the "rib" approximately 3/8 inch reward (toward the key entry end) from the cylinder release button.

12.3. Carefully drill a pilot hole through the plastic housing with a 1/8 inch drill bit.

12.4. Carefully drill a larger hole at the pilot location, and slightly into the ignition switch lock cylinder surface to break the release button retaining spring using a 9/32 inch drill bit.

12.5. Remove portions of the broken spring from the hole using a small suitable tool.

12.6. Grasp the ignition switch lock cylinder and remove it from the switch housing.

12.7. Remove any plastic "flash" from the drilling operation, and using compressed air blow out the ignition switch assembly.

12.8. Follow service manual procedures when cylinder cording is required. Refer to Key and Lock Cylinder Coding in General Information.

Installation Procedure
If the lock cylinder would not rotate or was seized, perform the following procedure:
1.1. Install the new ignition switch lock cylinder as required by rotating both the cylinder and the ignition switch to the ON position.

1.2. Push the ignition switch lock cylinder into the ignition switch housing until fully seated.

1.3. You may have to slightly depress the release button as the button passes by the 9/32-in hole previously drilled in the ignition switch housing.
9600af8.jpg Connect the electrical connectors.
Connect the Passlock? electrical connector.
Connect the park/lock cable to the ignition switchdd765ba.jpg Turn the key to the ON/RUN position. Install the ignition lock cylinder into the ignition switch. If you turned the key slightly while removing the lock cylinder, you may have to align the white colored ignition switch rotor (1) with the lock cylinder (2). You can rotate the ignition switch rotor (1) with your finger.
Remove the key
681874a.jpg Position the ignition switch to the instrument carrier.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Install the ignition switch bolts.
Tighten

Tighten the bolts to 10 N?m (89 lb in).

Install the trim plate bezel to the I/P cluster. Refer to Trim Plate Bezel Replacement - Instrument Panel (I/P) Cluster .
Install the knee bolster bracket. Refer to Bracket Replacement - Knee Bolster .
Install the steering column filler panel. Refer to Steering Column Filler Replacement .
Connect the battery ground cable. Refer to Battery Negative Cable Disconnect and Connect Procedure in Engine Electrical.

rate me fix ya cuz this is the fix 100%

Aug 17, 2008 | 2005 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...