Question about Cars & Trucks

Open Question

1994 chev.g20 van(Parking Brake Light Stays on)

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 341 Answers

SOURCE: POWER BRAKE BOOSTER REMOVAL,HELP!

remove master cly. from booster. then under dash remove clip & pin from brake pedal . pull carpet down remove 4 nuts . pull off booster..

Posted on Oct 21, 2008

  • 1 Answer

SOURCE: Electronic Control Module Installation 1994 G20 Chevy Van

I just had the same problem. If it is a regular van try under the driver seat in a plastic box. If it is a conversion van try in a pannel just behind driver seat on side of van wall behind a pannel that looks like a vent.

Posted on Apr 09, 2009

shadtremonky
  • 353 Answers

SOURCE: Truck stalls. 1994 Chev Van G20.

the ignition coil

Posted on Jun 25, 2009

rickvw345
  • 3 Answers

SOURCE: 1994 Chevy G20 Van - Van (auto trans) only has high (D) gear

Sound like you're going to need to drop the transmission pan so you can replace the filter along with fresh transmission fluid. I had a problem like that many years ago, this correct the problem... I also know that the throttle positioning sensor will also cause transmission shifting problems. I would start with the filter change then go from there... Good luck.

Posted on Aug 29, 2009

  • 99 Answers

SOURCE: 95 G20 Chevy van: ABS light stays on, pulls right when braking

im guessing you have a problem with one of the abs sensors...probably the front-left wheel sensor. the way they work is they detect when a tire is locking up faster then the others when the brakes are applied. if a tire locks, then the brakes on that tire are quickly released then re-applied, all in a very short amount of time. the sensor may be defective, and sending the cars computer a false signal, making the brakes on that side release a bit, while maintaining normal braking on the opposite side. thats most likely whats making your car pull. also, the abs light will only come on when there is an electrical problem with the abs system. so make sure todo a visual inspection of the wires for the sensors as well.

Posted on Aug 31, 2009

Testimonial: "Thanks for the excellent advice, I can't wait to try out the fix."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 G20 conversion van. 6 cylinder. Engine running in park. When I apply brake. Engine quits then van will not restart.


Check vacuum lines.
There is a large one on the power brake booster that goes to the back on the fuel system. Make sure you have vacuum before you try anything else.
A vacuum leak will cause you to stall out.

Dec 28, 2016 | 1994 Chevrolet G20

1 Answer

Where can I find a fuse block diagram for a 1994 chevy g20 van?


google fuse block diagram for a 1994 chevy g20 van, should pop right up

Jan 07, 2015 | Chevrolet Cars & Trucks

1 Answer

How do you remove the back seat from a 1994 chevy g20 van?


I believe the seats are bolted to the floor of the van. Make sure you unplug all electrical connections before removing the seats.

Feb 11, 2014 | 1994 Chevrolet G20

1 Answer

Flat rate for 94 chev van g20 w/350 ; replace engine oil cooler flex lines


alldata reports just over 1 hour to replace both lines

Jul 14, 2011 | 1994 Chevrolet G20

1 Answer

My parking brake light stays on and my brakes seem to be sticking as well.1995 Chev.pick-up,I pulled the rear wheels off and found I could still rotate the drum without any sticking or rubbing. Could this...


it sounds like the front brake slides/or pins are sticking i would service front calipers and apply lube where needed.For the brake light you would need to check the brake fluid level sensor turn it counter clockwise 1/4 turn and clean with brake clean if that doesn't work unplug the sensor and if light goes off replace sensor for brake fluid level.Also make sure parking brake is totally released.

Mar 23, 2010 | 1995 Chevrolet C1500

3 Answers

1994 Chevy van brakes grabbing


try replacing the brake hoses they may have a restriction causing

Jul 14, 2009 | 1994 Chevrolet G20

1 Answer

Have 1993 Chev Conversion van...can put seat back far enough...how do I/can I adjust brake pedal lower????


adjusting the brake pedal lower would call for a major modification of all braces an brackets under the dash

Jul 11, 2009 | 1993 Chevrolet G20

1 Answer

Parking break light is always on (1994 Toyota Previa)


If you look where the parking brake arm is you should se a switch that it pushes against . The switch should be right above the parking brake arm .

Feb 23, 2009 | 1994 Toyota Previa

2 Answers

POWER BRAKE BOOSTER REMOVAL,HELP!


remove master cly. from booster. then under dash remove clip & pin from brake pedal . pull carpet down remove 4 nuts . pull off booster..

Oct 19, 2008 | 1994 Chevrolet G20

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...