Question about GMC Cars & Trucks

Open Question

Canister purge valve for 2004 Yukon denali where is it located

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: location of fuse box/panel for 2004 yukon denali xl

There are 2 fuse panels in the Denali.
One is a panel on the drivers side, its on the dash but facing the door.

The ohter is under the dash and above the pedals, this one is much tougher to access.

Your Owner's Manual should tell you where the fuses are that you need to access.

Posted on Oct 20, 2008

savdragon
  • 37 Answers

SOURCE: Mustang GT 4.6 EVAP Canister Purge Valve Location?

You will need to remove the right front wheel & wheel well liner. The canister purge valve is behind the cover. It should have two tube going into the bottom and one on the side near the top.
You can fix it!
If this helps you out please rate me!
Brett

Posted on Mar 19, 2009

  • 104 Answers

SOURCE: I have a 2004 Avalanche, 49K mileage, code PO446,

That is an EVAP code. its a vent control code. you can manually test it by powering it up if you know where its at. i cant remember exaclty where its at off the top of my head but its only 2 wires. using a volt meter you want to make sure power is getting to it, but you cannot activate it without dealer scan tool.hmmm if you can figure out which is ground and power when you give it 12 volts it should click. meaning your vent solenoid works and you have wiring problems or its leaking.

EVAP problems are hard to finde with out scanners. you can change the vent solenoid and hope it fixes it. but a code points you to the direction of a problem. hopefull its not wiring problems. in the northern states with snow. ice can pull out wires and also get clogged in the vent solenoid and lock it up. its either wiring or bad or a leaking solenoid. check condition of wires. if they look good try a vent soleniod.

if that doesnt fix it after a engine light reset and 2 weeks or so. then goto dealer. you need to reset it after repair. light will not go off on its own.GOOD LUCK

Michael
ASE certified.
plz rate

Posted on Apr 29, 2009

  • 77 Answers

SOURCE: where is the purge valve located on a 2004 honda LX?

It is with a 2 wire Black connect located next to the throttle body. Locate the green cap on the evap hose and follow it to the throttle body and that is the purge valve.

Posted on May 17, 2009

  • 376 Answers

SOURCE: Where is the evap purge canister valve located on

The canister purge valve is located behind the intake manifold in the engine compartment on the firewall side .It should be a small round solenoid with a wire connector attached.It will have a feed hose from the evap cannister to the purge valve and then to the intake manifold.The evap canister is located on under the vehicle on the right side of the gas tank and is held in place by a bracket.If you follow these hoses it will also get you to the canister purge valve.I hope this helped.

Posted on Feb 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Canister Purge Valve located on 2004 Pontiac Vibe?


Pontiac Vibe Canister Purge Valve
It's usually close to or attached to the canister which should be under the vehicle close to the fuel tank

Feb 15, 2017 | 2004 Pontiac Vibe

1 Answer

How do I replace the purge valve on 2006 Yukon Denali


Replacing Vent Valve Solenoid Purge Valve Solenoid EVAP Valve 2005 GMC...

Remove the engine sight shield. Refer to Upper Intake Manifold Sight Shield Replacement . Remove the evaporative emission (EVAP) line from the canister purge solenoid, perform the following:
2.1.
Push the large size white retainer portion in.


2.2.
Push down, while pulling up slightly in order the disengage the tube.


Disconnect the EVAP canister purge solenoid electrical connector (1).
Remove the EVAP canister purge solenoid bolt (2). Remove the EVAP canister purge solenoid (3) and insulator (1).

Sep 19, 2015 | Cars & Trucks

1 Answer

Need to know where to find the canister purge valve


For the location of canister purge valve,check the following help links mentioned below:--
Click the link :---

Location for EVAP Purge Valve Solenoid?

http://schematicsdiagram.blogspot.in/2012/06/2002-nissandatsun-pathfinder-location.html


------------------

How to disconnect the hose form the Evap Canister?

http://schematicsdiagram.blogspot.com/2011/12/how-to-disconnect-hose-form-evap.html

-------------

2004 Chrysler PT Cruiser: Location of EVAP Purge Solenoid Valve?

http://schematicsdiagram.blogspot.in/2012/06/2004chrysler-pt-cruiser-location-of.html

-----------
These will help.
Thanks.

Jan 08, 2013 | Cars & Trucks

1 Answer

2004 gmc yukon....I have a strong gas smell coming from the driverside rear. Does anyone know what this could be, Nothing leaking????


Yes the vapor storage carbon canister is overloaded with fuel, this happens often from topping off or a faulty canister purge line or valve.

Oct 16, 2012 | GMC Cars & Trucks

2 Answers

Check engine light continues to come on even after replacing gas cap. Where is the evap Solenoid valve located on a 2007 gmc Yukon 5.3 L engine?


when u are infront of the car. exact location front side of the intake manifold,,,,,,,evaporative emission canister purge solenoid valve,5.3 L engine gmc yukon.

Jun 25, 2010 | Cars & Trucks

1 Answer

REPLACEMENT (EVAP) EVAPORATIVE EMISSION CASISTER SOLENOD ON 2001 DENALI


THERE IS A PURGE VALVE ON TOP FRONT OF INTAKE AND A VENT VALVE IN REAR ON DRIVER SIDE NEAR GAS TANK.GM HAS A UPDATED REPLACEMENT VENT VALVE WITH HOSES FOR $300. PURGE AND VENT VALVE WORK TOGETHER TO VENT FUEL VAPORS FROM GAS TANK.

Jan 27, 2010 | 2002 GMC Yukon Denali

1 Answer

Check engine light on 2004 GMC Yukon XL


Code po449 is the canister vent valve solenoid error.This is a common problem with these valves because they are under the truck in the rear by the spare tire and they get all the dirt and water and snow,if you live in an area where you get snow.You will find it on the canister under the vehicle by the spare tire.

Nov 18, 2009 | 2006 GMC Yukon Xl Denali

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...