Question about 2008 Dodge Avenger

Open Question

Where is the heater control valve located on a 2008 dodge avenger

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 141 Answers

SOURCE: 2008 Dodge Avenger window problem?

Sounds like u have a bad window regulator which is a system of channels and guide wires that move the window up & down. since i do not know the whole situation I would make sure the window channels are lubricated with silicone spray to make sure the window is not being held up on anything.

Posted on Jun 04, 2009

Ad
  • 1 Answer

SOURCE: Battery changing

Ok, trust me on this one, take the drivers side tire off and remove the forward inner fender panel. If you try it without removing the tire, it is just a royal pain.

Posted on Jun 10, 2009

  • 63 Answers

SOURCE: 2008 Dodge Avenger check engine light

Not sure if this will work for you but worth a shot. I own a 2005 dodge neon. I know the ecu's are different but maybe dodge was smart and made all the cars this way. Insert you key into ignition. Turn key forward until you are at the last position right before the car starts to crank over. Repeat this for a total of three times then on your digital odometer display, you will see a set of numbers displayed. this will be your code for the malfanction(s) that set your check engine light. Like I said, it might not work on your car but give it a shot. If not, rent an obdII scanner and get your codes. Then you know where to start looking to fix your problem.

Posted on Dec 17, 2009

sandman357
  • 236 Answers

SOURCE: Brake Fluid for 2008 Avenger

it's DOT 4 or DOT 5 check with your manual and sometimes it's even in the fluid fill cap.

Posted on Feb 22, 2010

Testimonial: "Quick response, guided me in the right direction. Thanks!"

  • 1 Answer

SOURCE: 2008 dodge avenger spark plug location and socket size.

  • 2008+ Dodge Avenger 2.4L 4cyl.
  • Remove plastic cover on top of engine, just pull on each corner for it is friction fit.
  • Once removed you will see 4 black spark plug covers with one hex type screw holding each.
  • Remove Hex screw and place aside, pull upward to remove plug boot from plug.
  • To remove the plug, use a 5/8 socket with a 6" extension. Once plug has been turned out all the way and you cannot get the plug up and out of the hole, just press the plug boot back on the plug and pull it back up.
  • Gap and replace 4 plugs with the same or equavalent type,. Drop plug down the hole and use socket to align and tighten until just snug, then torque to manufactures specifications.

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the shift soleniod located?


The transmission shift solenoids are located in the valve body, which is in the transmission. If you remove the transmission pan you will see the valve body. I believe any faulty shift solenoids are serviced as an entire valve body on the Avengers.

Dec 24, 2015 | 2008 Dodge Avenger

2 Answers

2008 dodge avenger code p2004


Intake Manifold runner control stuck open - bank one:
- Intake Manifold Runner Binding Or Sticking
- Faulty Manifold flow valve
- Manifold flow valve harness is open or shorted
- Manifold flow valve circuit poor electrical connection

There is a factory service bulletin for this problem for 2007-2008 Dodge Avengers. (JS)

Sep 22, 2015 | Dodge Cars & Trucks

1 Answer

I need to find the exact location of the starter motor relay for a 2008 dodge avenger


Starter Activation Is Controlled By Totally Integrated Power Module--Left Side Of Engine Compartment.
Can Be Checked With Scanner (buss lines) Has Solinoid On Starter

Feb 18, 2015 | 2008 Dodge Avenger

2 Answers

Where is the Location of a/c compressor clutch relay on 2008 dodge avenger


The compressor magnetic clutch is located and attached to the front of the AC compressor and the engine drive belt goes over it

Oct 03, 2013 | 2010 Dodge Avenger

1 Answer

Electronic throttle control indicator light


Here's the part,it's located near thermostat housing,easy to remove.

Dec 30, 2012 | 2008 Dodge Avenger

1 Answer

2008 Dodge Avenger fuel filter location


my father is fixing my 2008 dodge avenger,he cannot find where the fuel pump relay is located on my car

Feb 23, 2012 | 2008 Dodge Avenger

1 Answer

How do you bleed the brakes on a 2008 dodge avenger


U will need the special tool to hold open the ABS hydraulic control valve to get the air bubbles out of it, without the tool u will never get them bleed, sorry but the dealer is the only one that has this tool.

Dec 18, 2009 | 2008 Dodge Avenger

1 Answer

Where is the flasher relay located on a 1998 dodge avenger


The flasher on the avenger is mounted in the dash under and behind the heater controls. You will need to remove the panel under the heater controls to access.
This is a combination flasher that controls both signals and hazards.

Nov 03, 2009 | 1998 Dodge Avenger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...