Question about 2002 Dodge Durango

1 Answer

When i switch to my high beam lights they want stay on they cut right back off after like a second or two

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    New Friend:

    An expert that has 1 follower.

  • Dodge Expert
  • 229 Answers

Bad relay

Posted on Nov 13, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 328 Answers

SOURCE: 2001 dodge ram high beam indicator stays on

you likely have the wrong bulb in the headlight

Posted on Jan 07, 2009

  • 76 Answers

SOURCE: headlights alternate on and off left and right daytime/high beam

although the underhood relay panel is common, I'd check your headlamp bulbs first, these are cheaper than the fuse box. The daytime running lights work off the high beam circuit, thus, a blown highbeam bulb could be the culprit, the fusebox solution was more common on 2001 and up modles, although it's a definite possibility.

Posted on Feb 20, 2009

  • 1 Answer

SOURCE: headlights

disconnect the module that is mounted in front of the fuse box .Then carefully clean the the connectors ,they are usually pretty dirty.After they are clean put it back 2gether.If it doesnt solve the prob then u might have to stick some washers on your bottom screws so that your module is angled in.This will ensure a solid connection.

Posted on Jan 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Right low beam headlight does not come on but my right turn signal will stay even tho i diddnt turn it on. If I cut on my high beams the rurn signal cuts off. Whats wrong? Helo


It could be the lamp control module !
Headlamps
Battery positive voltage (B+) is applied at all times to the lamp control module (LCM) through the underhood fuse block HDLP fuse.
When you place the headlamp switch in the HEAD position, the headlamps input to the LCM is grounded. The LCM then applies battery positive voltage (B+) through the underhood fuse block HDLOBML fuse and HDLOBMR fuse, which feed the left low beam headlamp and the right low beam headlamp respectively. When you activate the headlamp dimmer switch by pulling on the multifunction lever until the switch clicks, the high beam input circuit to the LCM in grounded . The LCM then removes battery positive voltage (B+) from the low beam headlamps and supplies battery positive voltage (B+) through the underhood fuse block HDHIBML fuse and HDHIBMR fuse, which feed the left high beam headlamp and the right high beam headlamp respectively.
Check this fuse in the left under hood fuse box first. HDLOBMR Fuse 18 10 Amp. RH Low Beam Headlamp . If the fuse is good check for B+ voltage with the low beams on . Use a test light or volt meter . If you look on top of fuse there are two metal tabs ,check there for B+ voltage , If no B+ voltage the LCM - lamp control module isn't supplying any .
Lamp Control Module (LCM)
Under the left side of the IP, to the right of the steering column
Turn Signal Flasher
Under the left side of the IP, to the right of the steering column
Lighting Systems Component Views in Lighting Systems
Lighting Systems Connector End Views in Lighting Systems
Turn Signal/Hazard Switch
In the left front of the passenger compartment, in the steering column

Apr 28, 2016 | 2000 Buick Park Avenue

1 Answer

Hi Beam don't stay on VW Beetle 2002


It's the turn signal switch that is faulty.

Jul 26, 2015 | Cars & Trucks

1 Answer

My 2007 Chevy Silverado one ton headlights don't work you can hold the high beams back and they'll stay on but the second you like to go you have no lights at allany idea what's wrong is it a fuse ?


Replace the turn signal switch. All the exterior lights run the it, except the high mount brake light. Since you can get high beams to come on, the fuses are good.

Apr 09, 2015 | Cars & Trucks

2 Answers

My headlights on my sunfire go off while driving


Right now, I'm thinking the head lamp switch assembly has a problem? See the wire color in the top of head lamp, that is voltage, fuse protected, hot all the time. When problem is ongoing, you could use a test lite, check for voltage at fuse circuit?
The headlamp switch assembly is located on headlamp ground circuit. There could be a wiring problem, somewhere. I can only help with testing.
headlamps-mjson0k3fklv4nrxwvfsyjec-3-0.jpg

Apr 22, 2017 | 1996 Pontiac Sunfire

1 Answer

Headlights do not turn on my chevy cavalier. replaced light bulbs and high beams stay on but no low beams.


Sounds like your dimmer switch is stuck on or broken/worn out. Sometimes you can get it back by clicking your high beam switch in & out many times. If it frees up & switches back to lowbeam it will buy you time before you need to replace the dimmer switch. If not you will need to replace it right away.

Jun 16, 2010 | 1998 Chevrolet Cavalier

2 Answers

My low beam lights sometimes stop working i still have high beam and daylight runing lights after a while they come on.2009 elantra dealer can't find problem.


when the low beams quit try switching from high to low and back and see if low beams stay on, if they do it may be the dimmer switch, if that doesn't change anything suspect the headlight switch.

Sep 02, 2009 | 2009 Hyundai Elantra

1 Answer

High Beam Wire Color? Distinction between three?


with a test light ground connected to the positive battery terminal,,the one that will light up the light is the ground...the other 2 wires are the low and high beam. cut one of those,if the low beam is now on,you cut the high beam wire. if the high beam stays on,you cut the low beam wire.

Jul 22, 2009 | 1991 Toyota Tercel

Not finding what you are looking for?
2002 Dodge Durango Logo

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...