Question about Cars & Trucks

Open Question

Remove starter motor from chevy metro 98 - Cars & Trucks

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: how i remove the starter

Ok...I've left it for 3 days in my parking lot.....today...I've turned on the key and it started again.....I don't know what's next, nor if the problem it's fixed neither if it will happen again....

Posted on Jul 22, 2008

emissionwiz
  • 75077 Answers

SOURCE: how do i bypass the clutch starter safety switch for my 99 Metro?

jumper the connector to the clutch safety switch at the top of the clutch pedal lever.

Posted on May 25, 2009

theroadis
  • 81 Answers

SOURCE: Changing Blower motor on Chevy '98 4x4

It's simple!...Open glove box door...youll see a plastic shell that is the glove box rear portion. You should find 4, 9/32nds or 7mm (same thing just SAE or Metric) screw heads. Undo four screws and with a flat blade screw driver, gently pry out on shell at either side to clear the door straps. Once clear, just work out of resting place, set aside. You will now see like 5 relays mounted on top of the air handler. Remove bracket that holds four of them + one that is mounted alone. Pull out of the way. Checking both inside and outside, remove all screws, bolts, nuts as it were, until it is obvious there are none left. Now, this is assuming this is where your problem lies! If you are simply having a blower problem, it might be the blower module mounted right beneath and just behind relays on top of air handling box. Just take your time so you dont break anything. Good luck...theroad......

Posted on Jun 08, 2009

  • 2 Answers

SOURCE: How Do i replace Water Pump on 98 Chevy Metro

  1. Remove the negative battery cable.
  2. Drain the engine cooling system.
  3. Remove the air cleaner assembly.
  4. Remove the A/C compressor suction pipe bracket (if equipped).
  5. Loosen four water pump pulley bolts. Do not remove the bolts.
  6. Raise the vehicle. Support the vehicle. Remove the right lower splash shield.
  7. Remove the right lower splash shield.
  8. Remove the A/C compressor drive belt (if so equipped) by releasing the tensioner pulley and removing the belt from the crankshaft and compressor pulleys.
  9. Loosen the generator adjusting bolt (1), pivot the generator and remove the water pump/generator drive belt.
  10. Remove the crankshaft pulley.
  11. Remove the water pump pulley (four bolts).
  12. Remove the timing belt.
  13. Remove the oil level indicator (dipstick) guide tube.
  14. Remove the upper generator adjusting bracket from the water pump (one bolt).

    1. Remove the rubber seals from the water pump.
    2. Remove the water pump mounting bolts and nuts.
    3. Remove the water pump and gasket from the vehicle.
    4. Clean the water pump and the gasket mating surfaces.
    5. Install the water pump.
    6. Secure the water pump with mounting nuts and bolts. Tighten Tighten the water pump mounting nuts and bolts to 13 Nm (115 ft. lbs.).
    7. Install new rubber seals (1) to the water pump (2).
    8. Install the upper generator adjusting bracket to the water pump (one bolt).
        • Tighten the upper generator mounting bracket bolt to 23 Nm (17 ft. lbs.).
      1. Install the oil level indicator (dipstick) guide tube.
      2. Install the timing belt.
      3. Install the water pump pulley.
      4. Finger-tighten the four bolts.
      5. Install the crankshaft pulley.
      6. Install the water pump/generator drive belt to the crankshaft, water pump and generator pulleys.

Posted on Aug 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to put the Starter in a Eagle Talon 1991.


from autozone.com


REMOVAL & INSTALLATION
See Figures 5, 6, 7, 8, 9 and 10

  1. Disconnect the negative, then the positive battery cables from the battery.
  2. For 1990-94 vehicles, remove the battery and battery tray from the engine compartment.
  3. For 1990-94 vehicles, detach the speedometer cable connector from the transaxle.
  4. For 1995-98 2.0L turbo engines, remove the air hose.
  5. For 1995-98 2.4L engines, remove the air cleaner and air intake hose.
  6. If equipped with 1.8L engine, remove the bracket on the lower side if the intake manifold.
  7. Detach the starter motor electrical connections.
6f8c23b.gif

Fig. Fig. 5: Exploded view of the starter motor and related components-1990-94 vehicles, others similar


458b681.gif

Fig. Fig. 6: Unfasten the BAT terminal connector from the starter motor


05a1691.gif

Fig. Fig. 7: Unplug the starter motor electrical connector

  1. Unfasten the starter motor mounting bolts, then remove the starter from the vehicle.
d0adab9.gif

Fig. Fig. 8: Unfasten the starter mounting bolts
d00c214.gif

Fig. Fig. 9: Remove all of the starter mounting bolts ...
c92a470.gif

Fig. Fig. 10: ... then remove the starter motor from the vehicle
To install:

  1. Clean both surfaces of starter motor flange and rear plate. Install the starter motor onto the engine and secure with the retainer bolts. Tighten the retainers to the specifications shown in the accompanying figure.
  2. Attach the electrical harness connector(s) to the starter.
  3. If removed, install the intake manifold stay and tighten the retainers to 18 ft. lbs. (25 Nm).
  4. For 1995-98 2.4L engines, install the air cleaner and air intake hose.
  5. For 1995-98 2.0L turbo engines, install the air hose.
  6. For 1990-94 vehicles, attach the speedometer cable to the transaxle. Install the battery tray and battery.
  7. Connect the positive, then the negative battery cables.
Operate the starter to assure proper operation.

Oct 29, 2010 | 1991 Eagle Talon

1 Answer

How to take off crankshaft pulley on 2001 chevy metro. When I turn center bolt the pulley turns. Is there any other bolts that need to be removed? How do i remove this pulley?


if you have a standard transmission, put it in a high gear and set the parking brake.
If you have an automatic, you might have to remove the starter and lock the starter gear with a screwdriver or vicegrip. Make sense? Also, you may need a puller to get the vibration damper off the crankshaft.

Oct 12, 2010 | 2001 Chevrolet Metro

1 Answer

Where is the starter located on the metro


Four types of starter motor are utilized depending upon the vehicle transaxle and assembly plant location. Manual transaxle equipped vehicles utilize a conventional starter motor which consists of a yoke, an armature assembly, an overrunning clutch assembly, a solenoid, a commutator end cover, a brush holder and a pinion drive lever. Automatic transaxle equipped vehicles utilize a reduction type starter motor which has, in addition to the components found on conventional starter motors, a reduction gear and shock absorber assembly.


85162f4.jpg


Fig. 3: Starter motor assembly

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Label and disconnect the starter solenoid electrical connector.
  4. Remove the mounting bolts from the starter motor, then carefully lower the assembly from the vehicle.
To install:
  1. Install the starter motor assembly complete with any shims that may be used between the engine block and the starter.
  2. Install and tighten the starter mounting bolts to 17 ft. lbs.. (23 Nm).
  3. Connect the starter solenoid electrical connector.
  4. Lower the vehicle and connect the negative battery cable.

Hope helps.

Aug 01, 2010 | 1996 Geo Metro

1 Answer

My chevy metro 98 1.3L starts perfect but it does


can be a number of things from fuel pump to coil pack but check the egr valve may be starting to go -remove and check for carbon build up if not fully encrusted use a carb/or a carbon cleaning solution to clean and free up valve--most problems give a code but -fuel pump-filter-air filter dont and egr will sometimes set off other sensors but usually doesnt until its to late

Dec 10, 2009 | 1998 Chevrolet Metro

3 Answers

Where is starter located on 96 geo metro?


85d10dd.jpg

Starter motor assembly

In here can find one guide about replace the Starter in a Geo Metro

Dec 07, 2009 | 1996 Geo Metro

1 Answer

Changing starter on 97 geo metro 4 cyl 1.3


According to the tech maual, you get at it from underneath...these are the steps....removing the tire may help in having the "extra room".


  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Label and disconnect the starter solenoid electrical connector.
  4. Remove the mounting bolts from the starter motor, then carefully lower the assembly from the vehicle. To install:
  5. Install the starter motor assembly complete with any shims that may be used between the engine block and the starter.
  6. Install and tighten the starter mounting bolts to 17 ft. lbs.. (23 Nm).
  7. Connect the starter solenoid electrical connector.
  8. Lower the vehicle and connect the negative battery cable.

Aug 27, 2009 | 1997 Geo Metro

2 Answers

Where is the fuse for the radio?


most are tided together with the cig. lighter ,look in fuse box for radio, or cig. lighter. some radios have a inline fuse on them ,the radio has to be removed to run the wire down with the fuse link on it, try the fuse box first for cig.light ,hope this is some help to you, thanks robert b.

Jun 27, 2009 | 1998 Chevrolet Metro

1 Answer

1999 Chevy Metro Engine Fans don't work


Have you tried running wires directly to the battery to see if the fan motor works or needs to be replaced. Just get some number 10 or 12 electrical wire and run them to the battery. Try that maybe it's just that your fan motor needs to be replaced. Thanks for using Fixya.com...........Enjoy your evening : )

May 30, 2009 | 1999 Chevrolet Metro

1 Answer

I have a 2000 chevy metro 4 cyl 1.3 the vehicle runs great but when you leave the vehicle parked for two days the battery is dead the charging system is fine the alt the starter and battery all great and...


thats a good question. very hard problem to fix. i had a 2005 colorado i went through 4 batteries in 3 years. chevy could not find problem. they said i had a drain. never did find it sold vechicle.

Feb 25, 2009 | 2000 Chevrolet Metro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...