Question about 2003 Chevrolet Impala

Open Question

How to replace ball joint 2003 ford mustang - 2003 Chevrolet Impala

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 94 Answers

SOURCE: repalce ball joints 01' Chevy Blazer 4WD

you should just be able to loosen the half shaft and be ok that way

Posted on Mar 09, 2009

Ad
  • 1201 Answers

SOURCE: ball joint

The best I can tell you is, go to an auto parts store and get a haynes auto repair manual for that vehicle, it gives a step by step procedure on how to do it, About $16.00.

Posted on Jul 14, 2009

MNfisherman
  • 11896 Answers

SOURCE: broken upper ball joint on 2003 s10-4wd

You will have to unscrews, and pop the ball joint with seperator. A bottle jack also helps. Otherwise if you want more information, you can go to autozone.com and register for free. Then you will have full free online repair manual

Posted on Jul 17, 2009

  • 753 Answers

SOURCE: replace upper ball joint 2003 silverado 1500

The ball joints on both 2wd and 4wd upper are pressed in you need to remove snap ring and using a hammer pop out the old one out this is after you seperate the upper arm from the spindle. To install the new ball joint you should use a ball joint press that you can rent at most autoparts shops

Posted on Aug 09, 2009

  • 7 Answers

SOURCE: 2003 suburban

Jack up the affected side and support vehicle on stands.
04ad7d8.jpg
Remove nut that fastens onto affected ball joint;
Using a "pickle fork" (ball joint separator) hammer fork in between ball joint. Use at least a 5 Lbs. mallet to strike fork;38722d9.jpg
(Above: Blue wire is holding rotor assembly from flailing away after ball joint separation).

Using ball joint extractor, press out failed ball joint:
12cbf07.jpg
0c5ef57.jpg

Then fit in new ball joint and reassemble rotor assembly.


Posted on Sep 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I just change the upper ball joint on 2001 Mazda b2300


Old, Some times the hole control arm assembly is changed, if you can find it priced reasonably other wise yes, with proper tools the ball joint can be changed. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to Replace Ball Joints on Ford Ranger
Replacing Ford ranger ball joints
2003 Ford Ranger Ball joint and Control Arm Repair Part 1 Lower Ball Joint
Mazda B2300 Ball Joints eBay


May 19, 2016 | Mazda Cars & Trucks

1 Answer

How do I remove hub off of the end of the ball joint? It is stuck on the tapered end of the ball joint.


You can buy a special tool for spreading ball joints. It looks a bit like a large tuning fork with beveled tines. Place the open end between the ball and the hub, and hit the other end with a heavy hammer. The joint will separate and you can then remove the hub.

Oct 11, 2013 | 2002 Ford Mustang

1 Answer

Front suspension sound


if there are grease fittings present, grease them. if not there is a needle you can buy that will attach to your grease gun to puncture the seal boots on tie rod ends and ball joints to lubricate them

Aug 11, 2012 | 2003 Ford Mustang

1 Answer

How to remove spindle to get to lower ball joints on 1994 ford mustang


Jack vehicle up and set on jack stand (on frame) remove tire, brake caliper, place a jack under the lower A arm leaving a small gap between (3/8") the jack and the A arm. Spray area with WD 40 remove the nut from the ball joint. Strike the spindle with a hammer (single blow at a time) in the area were the tapered shaft of the ball joint goes through it and it should release it, then you can lower the A arm down slowly releasing the spring tension.

May 06, 2011 | 1994 Ford Mustang

2 Answers

How do you change a ball jiont on a 95 mustang. i have it un screwed but its stuck. i can't get the screw out.


Hi:
Most Ball joints have an internal or external snap ring, that must be removed, and then the entire ball joint is pressed in place.
the threaded part does not come out of the joint.
If you are serious about changing them yourself, most auto parts stores, such as Autozone, have a loan a tool program, and have the tools you need to remove the ball joint from your car!

Oct 04, 2010 | 1995 Ford Mustang

1 Answer

How do i replace cv joint on a ford taurus 2003 i cant get the control arm off please help


The control arm is attached with the ball joint,remove the nut on the ball joint,and hit around the stud of the ball joint,hit it hard,but do not hit the stud of the ball joint,it will jar it loose,then use a large pry bar,and stick in the control arm and pry downwards,It is not easy to get the ball joint stud out of the spindle,but it is the only way.but make sure the stud of the ball joint is free from the control arm then push down on the control arm(pry)

Apr 24, 2010 | 2003 Ford Taurus

1 Answer

How do you get the lower ball joint off a 2001 mustang it broke into


hi, have you tried using a ball joint splitter these can be brought for next to nothing and should do the job, if how ever you have tried one of these then the only other option would be to hit the hub where the ball joint goes into to shock it out you will need a big hammer to do this like a small lump hammer then if you keep giving the hub a hard hit just at the side where the ball joint is this should then shock it out and then it should just fall out.

Mar 26, 2010 | 2001 Ford Mustang

1 Answer

I need information on my daughters 1998 Ford Mustang on replacing ball joints.ie on part numbers and how to do the job. Maybe a front suspension illustration with nomenclature of the different parts and...


1998 Ford Mustang 3.8L SFI 6cyl

Visit autozone.com (free register) for details like this...
Lower Ball Joints

f8a9122.jpg

Fig. 1: When inspecting the lower ball joints, make sure the checking surface protrudes outside the cover

8e5561c.jpg

Fig. 2: Use a C-clamp and adapters to press the ball joint out of the lower control arm

93a6054.jpg

Fig. 3: Use the C-clamp, cup and replacer tools to press the new ball joint into the lower control arm until it is fully seated in its bore

Hope help you with this, good luck (remember rated this help).

Sep 25, 2009 | 1998 Ford Mustang

2 Answers

Ball joint replacement-2003 Ford Sport Trac


if you dont have a ball joint press and dont know how to use one then dont do it, but if you do its not that bad of a job just jack the truck up under the control arm remove the brake rotor then take the lower ball joint nut off then use a pickle fork to break the ball joint loose then take the axle nut off push the axle out of the bearing and use the ball joint press to remove and replace the ball joint

Jul 19, 2009 | Ford Sport Trac Cars & Trucks

Not finding what you are looking for?
2003 Chevrolet Impala Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...