Question about Lexus Cars & Trucks

Open Question

Lexus is220d sluggish and vsc and warning light on

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3741 Answers

SOURCE: 2007 lexus rx350 ,vsc light on and check engine light is flashing

First check and make sure your gas cap is tight, if this does not resolve the problem read below.
A vacuum hose has become disconnected, more than likely due to having your air filter replaced. The VSC and Check engine light typically don't come on until after 150-200 miles after the vacuum hose was pulled out.
The fix: on the right-hand-side of the engine compartment behind the big plastic housing that holds the air filter you will find a black rubber hose that is not connected to anything. Squeeze the finger clamp on the hose and slide the hose back onto the half inch nipple on the back of the air filter's plastic housing.
In order for the VSC and Check engine light to be turned off, you will need to open the fuse box, right-side of the engine compartment, and pull the 20 amp EFI fuse for 10 seconds. This will reset the system. The fuse location is marked on the lid of the fuse box, also I believe the EFI fuse is the only 20 amp fuse
. This will help. Thanks, please keep updated. please do rate the solution positively .thank you for using fixya


Posted on Dec 29, 2009

Ad
  • 430 Answers

SOURCE: How do I reset the VSC trac warning light on my

see my RX and GX posts earlier today for same symptom

Posted on Dec 29, 2009

  • 430 Answers

SOURCE: when starting my lexus GX 470 the vsc off light

The VSC on TRAC off lights will come on when there is an air fuel related issue.
If you have recently filled your tank, unscrew and tighten the gas cap till it clicks. The lights may need to be reset if they stay on after that. They will also be triggered by a fouled O2 sensor ins the engine or exhaust as well as a sticky throttle valve.
If a dealership resets the lights they can attach a code reader under dash to determine the cause in about 5 minutes.

Posted on Jan 10, 2010

  • 1 Answer

SOURCE: 2001 lexus ls430: warning

yaw sensor is out of calibration, most likely from hoisting vehicle in air. sensor needs to be calibrated before light will go out. jump pin 3 and 5 of dlc under driver side dash. connect jumper wire with ignition off, turn ignition on, vsc light should flash, let it flash for awhile (10 sec). turn ignition off and disconnect jumper wire.(do this with vehicle station on ground).

Posted on Sep 21, 2010

  • 1 Answer

SOURCE: lexus gs300 vsc check engine light gas pedal no acceleration

I have a a 99 gs 300, check engine light is on as well as the vsc light. What is that and needs to be to done to fix it.

Posted on Nov 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hy.I'm Adrian.I have a lexus is250 from 2006 and I just changed the battery and apear the VSC CHEK LIGHT and ENGINE LIGHT.and a c1201 and p2118 error codes.please someone can help with some suggestin


Code P2118 throttle control motor is set when voltage to the motor gets below 4 volts, so perhaps this was set with old dead battery. code C1201 is a vague engine control code, and the VSC vehicle stability code is set anytime you hook up a scan tool other that the dealer's special unit. You must reset the zero point calibration for this to go away. Use your scan tool to erase all codes to see if any come back. This will not turn off the VSC light, however. Follow below procedure to reset zero point calibration.

Zero Point Calibration - "VSC" and "VSC Off" Lights - 2002 SC430 - SOLVED
________________________________________
Friends,
For the benefit of any 2002 Lexus SC430 owners, I'll post the following item dealing with "Zero Point Calibration".
After hours of troubleshooting, I came to the hypothesis that the instructions MIGHT be different from 2002 - 2005 and 2006 - 2010 models. Below are the instructions I followed and WORKED on my 2002 SC430.
If you receive the "VSC" and "VSC Off" lights on the dashboard after a visit to a mechanic (often an independent mechanic using non-Lexus ODBII equipment), this means your "Zero Point Calibration" has been erroneously reset by a non-Lexus specific ODBII tool. This might especially happen if your state requires state inspection via ODBII, and you take your Lexus to a no-name place (like a Jiffy Lube or something). Follow the steps described in Post #6 in this thread to resolve this issue:
http://www.clublexus.com/forums/gs-2...d-vsc-off.html
Note that where you see a reference to a tool called the "SST 09843--18040", substitute that "tool" for a simple jumper cable (such as a short speaker wire) or a paperclip.
Here is the relevant excerpt from the above thread:
"The solution consists of approximately 15 step .
NOTE:While performing the Zero Point Calibration, do not tilt, move or shake the vehicle.
The vehicle must remain in a stationary condition throughout the entire process.
Be sure to perform the procedure on a level surface with an inclination of less than 1%.
Explanation of symbols:
SST (4-inch wire)
DLC3 (OBD-II connector under the dash)
TS (on the top row,pin number 3)
CG (on the bottom row,pin number 5)
(See picture below)
1. Ensure the shift lever is in the ''P'' range.
2. Turn the ignition switch Off.
3. Using SST 09843--18040, repeat a cycle of short and open between terminals Ts and
CG of DLC3 4 times or more within 8 seconds (refer to the specific vehicle EWD for
TS and CG pin location in the DLC3).
4. Turn the ignition switch ON, do not start.
5. Verify that the VSC indicator light is lit indicating the recorded zero point is erased.
6. Turn the ignition switch OFF.
7. Be sure the terminals Ts and CG of DLC3 are disconnected.
8. Turn the ignition switch ON, do not start.
9. Check that the VSC warning light goes off about 15 seconds after the ignition switch
is turned ON.
10. After ensuring that the VSC warning light remains OFF for 2 seconds, turn the ignition
switch OFF.
11. Connect terminals Ts and CG of DLC3 using SST 09843--18040.
12. Turn the ignition switch ON, do not start.
13. After turning the ignition switch ON, check that the VSC warning light is lit for about
4 seconds and then starts quick blinking at 0.13 second intervals.
14. After ensuring the blinking of the VSC warning light for 2 seconds, turn the ignition
switch OFF.
15. Remove the SST from terminals Ts and CG of DLC3.
16. Drive the vehicle for at least 5 minutes to confirm Zero Point Calibration is complete."

Oct 29, 2016 | Lexus Cars & Trucks

1 Answer

What is the light stating vsc is off what is this


VSC is vehicle stability control system. Read codes with a GOOD scan tool for more information. On Toyota and Lexus cars, using a scan tool other that the dealer tool will trigger VSC off and VSC lights, which can be reset using a procedure of key off, shift to certain gears, key on etc. as follows:

Friends,
For the benefit of any 2002 Lexus SC430 owners, I'll post the following item dealing with "Zero Point Calibration".
After hours of troubleshooting, I came to the hypothesis that the instructions MIGHT be different from 2002 - 2005 and 2006 - 2010 models. Below are the instructions I followed and WORKED on my 2002 SC430.
If you receive the "VSC" and "VSC Off" lights on the dashboard after a visit to a mechanic (often an independent mechanic using non-Lexus ODBII equipment), this means your "Zero Point Calibration" has been erroneously reset by a non-Lexus specific ODBII tool. This might especially happen if your state requires state inspection via ODBII, and you take your Lexus to a no-name place (like a Jiffy Lube or something). Follow the steps described in Post #6 in this thread to resolve this issue:
http://www.clublexus.com/forums/gs-2...d-vsc-off.html
Note that where you see a reference to a tool called the "SST 09843--18040", substitute that "tool" for a simple jumper cable (such as a short speaker wire) or a paperclip.
Here is the relevant excerpt from the above thread:
"The solution consists of approximately 15 step .
NOTE:While performing the Zero Point Calibration, do not tilt, move or shake the vehicle.
The vehicle must remain in a stationary condition throughout the entire process.
Be sure to perform the procedure on a level surface with an inclination of less than 1%.
Explanation of symbols:
SST (4-inch wire)
DLC3 (OBD-II connector under the dash)
TS (on the top row,pin number 3)
CG (on the bottom row,pin number 5)
(See picture below)
1. Ensure the shift lever is in the ''P'' range.
2. Turn the ignition switch Off.
3. Using SST 09843--18040, repeat a cycle of short and open between terminals Ts and
CG of DLC3 4 times or more within 8 seconds (refer to the specific vehicle EWD for
TS and CG pin location in the DLC3).
4. Turn the ignition switch ON, do not start.
5. Verify that the VSC indicator light is lit indicating the recorded zero point is erased.
6. Turn the ignition switch OFF.
7. Be sure the terminals Ts and CG of DLC3 are disconnected.
8. Turn the ignition switch ON, do not start.
9. Check that the VSC warning light goes off about 15 seconds after the ignition switch
is turned ON.
10. After ensuring that the VSC warning light remains OFF for 2 seconds, turn the ignition
switch OFF.
11. Connect terminals Ts and CG of DLC3 using SST 09843--18040.
12. Turn the ignition switch ON, do not start.
13. After turning the ignition switch ON, check that the VSC warning light is lit for about
4 seconds and then starts quick blinking at 0.13 second intervals.
14. After ensuring the blinking of the VSC warning light for 2 seconds, turn the ignition
switch OFF.
15. Remove the SST from terminals Ts and CG of DLC3.
16. Drive the vehicle for at least 5 minutes to confirm Zero Point Calibration is complete."

Oct 19, 2016 | Cars & Trucks

1 Answer

Toyota kluger 1007 how to remedy vsc light on. vsc not on


Not sure if this will help, but my 2002 LEXUS sc430 had this issue, and it turns out that if you plug any scan tool other than the dealer unit in, it will cause this VSC lights to come on. It requires that you reset the "zero point calibration" for the skid system, which is done by first: have car on level ground with less than 1% slope in any direction. Next, follow these directions:

If you receive the "VSC" and "VSC Off" lights on the dashboard after a visit to a mechanic (often an independent mechanic using non-Lexus ODBII equipment), this means your "Zero Point Calibration" has been erroneously reset by a non-Lexus specific ODBII tool. This might especially happen if your state requires state inspection via ODBII, and you take your Lexus to a no-name place (like a Jiffy Lube or something). Follow the steps described in Post #6 in this thread to resolve this issue:
http://www.clublexus.com/forums/gs-2...d-vsc-off.html
Note that where you see a reference to a tool called the "SST 09843--18040", substitute that "tool" for a simple jumper cable (such as a short speaker wire) or a paperclip.
Here is the relevant excerpt from the above thread:
"The solution consists of approximately 15 step .
NOTE:While performing the Zero Point Calibration, do not tilt, move or shake the vehicle.
The vehicle must remain in a stationary condition throughout the entire process.
Be sure to perform the procedure on a level surface with an inclination of less than 1%.
Explanation of symbols:
SST (4-inch wire)
DLC3 (OBD-II connector under the dash)
TS (on the top row,pin number 3)
CG (on the bottom row,pin number 5)
(See picture below)
1. Ensure the shift lever is in the ''P'' range.
2. Turn the ignition switch Off.
3. Using SST 09843--18040, repeat a cycle of short and open between terminals Ts and
CG of DLC3 4 times or more within 8 seconds (refer to the specific vehicle EWD for
TS and CG pin location in the DLC3).
4. Turn the ignition switch ON, do not start.
5. Verify that the VSC indicator light is lit indicating the recorded zero point is erased.
6. Turn the ignition switch OFF.
7. Be sure the terminals Ts and CG of DLC3 are disconnected.
8. Turn the ignition switch ON, do not start.
9. Check that the VSC warning light goes off about 15 seconds after the ignition switch
is turned ON.
10. After ensuring that the VSC warning light remains OFF for 2 seconds, turn the ignition
switch OFF.
11. Connect terminals Ts and CG of DLC3 using SST 09843--18040.
12. Turn the ignition switch ON, do not start.
13. After turning the ignition switch ON, check that the VSC warning light is lit for about
4 seconds and then starts quick blinking at 0.13 second intervals.
14. After ensuring the blinking of the VSC warning light for 2 seconds, turn the ignition
switch OFF.
15. Remove the SST from terminals Ts and CG of DLC3.
16. Drive the vehicle for at least 5 minutes to confirm Zero Point Calibration is complete."
Attached images

Oct 03, 2016 | Toyota Cars & Trucks

1 Answer

Lexus RX-330 2004, 135,000miles. Shows light "ENGINE, VSC/TRAC OFF" . Answered from Auto repair shop - Catalytic Converter and 2 geskets $756.00 incl. tax. Answered from Lexus Dealer-Bank2 Cat and


Try to look for any electrical fuse problem in your car... from there you can do a visual check in all of your fuse... if it is busted get some expert to help you out... remmember don't do anything if you are not sure about it

Feb 13, 2015 | Lexus RX 330 Cars & Trucks

1 Answer

2007 Lexus,RX 350, 101,200 mileage - Malfunction Indicator Lamp and VSC lights came on after driving 30/40 miles. Vehicles driving performance seems normal. Checked Gas Cap. The only Dealership close by...


If you have MIL get the codes scanned, at least they will help point you at the real cause of the problem. For the moment ignore the VSC warning until the MIL has been successfully diagnosed and cured. Nine times out of ten curing the MIL will resolve the VSC warning.

Mar 31, 2011 | Lexus RX 350 Cars & Trucks

2 Answers

VSC Warning light - Have checked the gas fuel cap for snugness


VSC = Vehicle Stability Control, its possible that you have any wheel sensors problem.

Jan 10, 2011 | 2006 Lexus Gs 300

2 Answers

Trac off, trac vsc and check engine engine lights


Battery was diconnected for 1 minute and then reconnected. All lights are off.

Mar 24, 2010 | 2002 Toyota 4Runner

2 Answers

While driving vehicle, the VSC Off warning light


vsc(vehicle stability control) is usally part of the abs(anti lock brakes) could be as simple as a bad wheel speed sensor

Feb 24, 2010 | 2004 Lexus GX 470

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

905 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...