Question about Cars & Trucks

1 Answer

1991 firefly

Missing button you push in before starting.Can i use something instead to get it to the shop?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,113 Answers

Yes... MacGyver it!

Posted on Oct 20, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Is there a certain type of gasket or something else when there is a oil leak starting in a 1998 pontiac firefly

clean around the oil pan gasket area well as some oil leaks are actually rocker cover gasket and filter leaks that run down the block and appear as pan leaks.. Check front crankshaft seal as the oil from there also appears as a pan leak

Dec 10, 2014 | Pontiac Cars & Trucks

1 Answer

91 geo tracker died while driving cant get it started again

when you crank it, do you smell fuel? if you do, you're getting fuel so try replacing the distributer cap and even the plugs. if no gas smell, the fuel filter needs changing or the fuel pump is bad.

Feb 27, 2014 | 1991 Geo Tracker

1 Answer

How to bypass the starter relay and put it to a push button to start the car

A wire run from the starter solenoid postive (+) terminal to a button somewhere on the dash panel is all that is required You need to connect the other side of the press button to a power source under the dash. The fuse box is a good place to start. Make sure your wiring is protected against shorts by a fuse. If the vehicle is an auto, don't do this. Get the inhibitor switch replaced instead.

Mar 18, 2010 | 1991 Isuzu Pickup

1 Answer

1991 audi will push start but not with the key. My shop says they do not have the correct tools and the nearest audi dealer is a long long way away. Is there something I can do to fix it myself?

chances are it's a bad starter/solenoid, check the grounding strap from solenoid to starter (exposed braided wire) tend to rot after time

Feb 15, 2010 | 1995 Audi 90

1 Answer

I have (or my kid has) an old 91 firefly with a

yes drain the coolant and then add 200grms of caustic soda and run engine till hot then give a good flush and then remove the heater feed pipes and flush with hose reversing direction a couple of times ,might help but cant guarentee it because the layout of the heater coil is such that the water doesnt pass from one side to the other but the inlet and outlet are both on teh same header tank .But the caustic will help to more some of the clag

Dec 12, 2009 | 1991 Mitsubishi Montero

1 Answer

Antilock brake light on & Red brake light on

yes you should/ Take it to an dealer body shop rates are better instead of paying 110.0 or more body shop mechanical raate rates are 85.00 but get it checked it may be something more Please rate my response/ Thank you very much

Jan 31, 2009 | 1991 Jeep Cherokee Briarwood

1 Answer

Ignition timing for 1991 Pontiac Firefly or 1991 Chevrolet Sprint or 1991 Geo Metro

for 1991 geo metro 1.0 liter 3 cyl engine the timing is 6 degrees before top dead center. you will need a tachometer because the rpm must be 800 when you set the timing. also you will need to disconnect the vacuum advance to the distributor, and plug the hose to avoid a vacuum leak. (alternate method is to pinch the vacuum advance hose going to the distributor while you are setting the timing) Good Luck!

Oct 28, 2008 | 1991 Geo Metro

1 Answer

1991 honda civic hb si please help!!

Sounds like it may be a vacuum line problem...double check all the hoses and make sure none are off or broken/missing. Check over the IAC (Idle Air Control) valve too and inspect & clean it out with carb clean or something, could be that the valve's sticking

Oct 07, 2008 | 1991 Honda Civic

2 Answers

1991 jaguar xj6 RADIO couldn't turn ON! The radio can't turn its power on by the switch, the security indicator keeps flashing all the time no matter the switch is "ON" or "OFF". the fuses are good and the...

1991 jaguar xj6 RADIO couldn't turn ON! The radio can't turn its power on by the switch, the security indicator keeps flashing all the time no matter the switch is "ON" or "OFF". the fuses are good and the relays that I COULD find (in the trunk for the antenna) are good as well. I have power GOING to the radio from all indications but it doesn't come on or flash CODE for me to enter, which I do have. Is there something I'm missing or is the radio just shot? Also I found no fuse on the radio it's self. Is there some SIMPLE fix out there? Or should I START SHOPPING?

Jun 15, 2008 | 1993 Jaguar XJ6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides