Question about Ford Cars & Trucks

1 Answer

Need to remove the rear axles on a 1964 ford ranchero 8 inch rear end

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 364 Answers

Jack and suppoet with stands, put vehicle in neutral, ensure emergency brake is off. remove rear wheels, remove drums, you will see a hole in the axle end to fit a socket to undo 4 nuts, if you don't have a slide hammer, put wheel on without drum and get underneath and kick wheel. U must make sure the car will not fall, better safe than sorry. {you shouldn't have to remove brakes} good luck

Posted on Oct 20, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Rear Axle Removal

if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals

Posted on May 30, 2008

  • 883 Answers

SOURCE: Rear Axle Removal

rate me solved...this is all I can find...

figure 1

d164665.jpg

figure 2
c12dde8.jpg

defeae4.jpg

Posted on Jun 27, 2008

  • 2 Answers

SOURCE: rear differential axle removal

remove the 'locking bolt', once the pin is out the c-clips shoud fall out unless this is a floating axle in which the axles are attached at the hub.

Posted on Sep 12, 2008

chuck943
  • 783 Answers

SOURCE: torque specs 7.5 inch rear axle 96 ford ranger

Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Posted on Jan 30, 2009

  • 51 Answers

SOURCE: Left rear axle seal is leaking differental oil.

ok then here is the procedure  1 take off the axle nut
2 on the lower control arm you will find a large nut and bolt i belive the nut is a 21mm and the bolt side is an 18mm. this bolt is the one at the knuckle near the brakes. remove it
3 you will need to pull the knuckle out of the way or a helper to pull the knuckle out of the way so you can slip the axle out of the knuckle.( its a tight fit but there is room to slip it out.)
4 use a pry bar to pop the axle free of the diff. hosing its held in by a spring clip make sure the clip comes out with the axle if it gets stuck inside you will have to fish it out.
5 use a pry bar or screwdriver to pry seal out of housing then use a flat object that contacts the entire rim of the new seal so it can evenly be installed with out getting smashed and tap it in with a hammer. ( a good trick here is to use some grease and pack it into the new seal where the spring is this will prevent the spring from being shocked out of the seal during instalation . the spring keeps tension on the rubber in the seal so it stays tight to the shaft it is sealing.)
6 then revers the above steps. also make sure you are using the right gear lube it will most likely be 75w-140 but make sure you check your owners manual will tell you if it doesnt say on the diff cover. you can cause a lot of damage if you put in the wrong thing. and make sure  you feel the axle spring clip snap into place.
as a note there are two types of axle seals that are used on these so if the new seal looks different than the old seal then the folliowing will be important to you.the seals on these have been redesigned so if you axle has what looks like a cup or dust cover pressed onto the shaft where it goes into the diff the new style does not use this and it will prevent the axle form going in all the way so the spring clip will not lock in and you will have a leak. so you will have to remove it and install the axle without it.

Posted on Mar 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1964 Ford Ranchero, advice on repairing sloppy steering mounted gear change


If you look under the hood where the shifter linkage goes from the column to the transmission. You should have 3 rods, and at the ends of the rods should be bushings. Over time, these bushings wear out and disintegrate away. You should be able to purchase a kit to rebuild your shift linkage. Just make sure you label the rods location and orientation before you remove them. It can become quite a headache if you get them out of order.

Oct 15, 2015 | Ford Cars & Trucks

1 Answer

How do I remove the rear end on a 1999 ford F150


Turn the differential around until you find the small bolt that is holding the differential pinion shaft into the carrier housing, this is the shaft thar runs through the carrier housing that the spider gears rotate on. Remove the bolt and slide the pinion shaft out towards you, if you have limited slip there will be a metal spring shaped kind of like an S that will need to be carefully pried out using a screwdriver or pry bar. You will need to remove the brake drum or rotor depending what type of brake you have on the left side, then just push the axle into the housing about half an inch, look in the center of the carrier housing on the end on the axle you just pushed inward, there will be a C clip on the end of the axle. The C clip looks like a washer with a notch cut in it, remove the C clip using needle nose pliers or a magnet, the axle should now just pull out.
Source(s):

Mar 13, 2015 | 1999 Ford F150 Regular Cab

1 Answer

How to remove rear wheel bearings on my 1999 Ford Expedition and how do i know what pulley to rent/buy?


The 1999 Ford Expedition is built on an F150 platform. The Expedition uses a 9.75-inch rear axle. The axles are retained with C-clips at the end of the axle shaft, inside the differential carrier. The axle bearings are of the roller type. A failed axle bearing can manifest itself as a noise at the rear wheel or gear oil leaking past the oil seal. When replacing axle bearings, the oil seals must also be replaced.
Torque the caliper mounting bolts to 30 foot-pounds. Torque the bolt to 20 foot-pounds with a torque wrench and socket. Click this link below for complete detailed procedure:--- http://technoanswers.blogspot.com/2011/06/how-to-remove-rear-wheel-bearings-on.html -------------- This should help.Thanks.Helpmech.

Jun 07, 2011 | Ford Expedition Cars & Trucks

1 Answer

How to remove axel on 2002 cadillac deville


this procedure is for replacing the axle bearing, it has all the info u need to do whatever it is u are doing with the axle removed.

Instructions Things You'll Need:
  • Floor jack
  • Jack stands
  • Axle puller
  • Set of 3/8-inch drive sockets
  • 3/8-inch drive ratchet
  • Needle nose pliers
  • Set of ¼-inch drive sockets
  • ¼-inch drive ratchet
  • Hammer
  • Lug wrench
  • Tube of RTV silicone
  • 2 bottles of rear axle oil
  • Bucket
  1. Step 1 Raise and support the rear of the vehicle. Remove the wheels. Remove the rear cover on the third member or axle. Place the bucket under the rear to catch the fluid. Remove the brake drums if the vehicle has drum brakes.
  2. Step 2 Rotate the outside axle until the center carrier is in a position where the small 8 mm or ¼-inch bolt is at 7 o'clock and clear of the housing so that it can be removed. This is the bolt holding the center through pin that runs through both spider gears. Position the carrier so that when the bolt is removed, the pin can be dropped straight down without contacting the housing.
  3. Step 3 Remove the center pin and lay it in the cover with its retaining bolt. Do not rotate the carrier with the pin out, since the pin is what holds the spider gears in place. If the carrier is turned, the spider gears would need to be adjusted so that they line up again with the hole for the through pin.
  4. Step 4 Push both axles in toward the carrier. This is now possible because the through-pin has been removed. This will expose the C-clips that hold the axles from coming out of the carrier. Remove the C-clips with the needle nose pliers and lay them in the pan. Pull the axles out of the housing and stand them up.
  5. Step 5 Remove the outside axle bearings and seals with the axle puller. The axle puller has several ends of different sizes; pick the one that fits through the center of the bearing. The axle puller is a sliding hammer with a T-end that can swivel. When the puller end is inserted through the bearing, rotate it slightly to get the T-end to swivel up and grab the bearing. Using the slide hammer, hammer the bearing and seal out of the housing.
  6. Step 6 Clean the housing surface where the bearing will be seated. Place the new bearing into the housing as far as it will go, and make sure it goes in straight. Place the old bearing on top of the new bearing and hit it with the hammer to drive the new bearing in. Tap it on in a circular pattern and continue until there is a resounding difference in sound as the bearing contacts the lip in the axle (it will sound more solid). Remove the old bearing.
  7. Step 7 Install the seal by tapping it carefully on four corners, avoiding the rubber part of the seal, until it is seated. Do not bend the housing or it will leak.
  8. Step 8 Install the axles and push them in all the way. Insert the C-clips on the ends of the axles and pull the axles back out to seat the C-clips in the carrier. Insert the pin back into the carrier through the spider gears and install the small retaining bolt to keep the pin in.
  9. Step 9 Clean the face of the housing and the axle cover where the gasket material will seal. Use brake cleaner or alcohol to remove all the oil from the surface to be sealed. Smear some RTV silicone sealant on the axle cover around the edge in a continuous line about a quarter of an inch thick. Allow the cover to sit until the RTV silicone sealant cures to the point that it will not transfer to the fingers when touched. The proper terminology is when it "skins," or is still wet inside but starting to dry on the outside; this way it will stay in place.

Jul 02, 2010 | 2002 Cadillac Deville

1 Answer

I need to remove the rear axles to 1996 ford bronco


remove rear cover from rear differential. catch nasty smelling oil (gear lube) in drain pan. remove bolt on side of carrier to be able to pull pin out from so called spider gears. if you have limited slip you may hve to pull S spring out from between side gears. then push axles in and remove C clips fom end of axles. then pull axles out. installation is in reverse of removal. make sure that the C clips are well installed in the groves whe reinstalling axles, or they could fall out and axles will come out while driving. bad deal.if you have limited slip get a bottle of friction modifier from parts store to put in there with new gear lube . is a small bottle like 6 to 8 oz.kepps clutch packs from chatering on turns.

Nov 07, 2009 | 1994 Ford Bronco

1 Answer

How do you remove right rear axle on a 2004 ford crown vic to replace seal on wheel?


Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
  1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .




  1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.
  1. Drain rear axle lubricant by removing the axle housing cover .
  1. Remove differential pinion shaft lock pin and differential pinion shaft .


    9979cb3.gif
  1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .



  1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.
Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
  1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .
  1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .
  1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.




    NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
  1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).



  1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
  1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).
  1. Install rear disc brake caliper and rear disc brake rotor .
  1. Install wheels and tires.
---------------------------------------------------------
  1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.

    Rear Disc Brake Caliper Anchor Plate




  1. Lubricate the rear wheel bearing with Rear Axle Lubricant.



  1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.



    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
  1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .



  1. Install axle shafts as outlined.

May 13, 2009 | 2004 Ford Crown Victoria

1 Answer

Need to know where the rear axle pins are in 98 s10 blazer


No "axle pins". Axles are held in with "c" clips. Remove wheels. Remove drums (or rotors). Remove differential cover. Rotate axles or driveshaft until a small bolt running horizontally can be seen. It has an 8 millimeter head. Remove this bolt. It holds in a shaft that is about 1 inch in diameter an 3 inches long. Remove that shaft. Shove axle towards center of vehicle one at a time. C clip can now be removed from internal end of axle and axle can be slid out of axle housing. When axles are removed DO NOT ROTATE DRIVESHAFT OR CARRIER.

May 01, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Torque specs 7.5 inch rear axle 96 ford ranger


Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Jan 30, 2009 | 1996 Ford Ranger SuperCab

1 Answer

I need to disassemble a Ford 9" third member


Is this a 9" inch rear end? if so unbolt the axles from from the out side behind the brakes and pull them out, then remove the drive shaft rear u joint saddles and drop the drive shaft down, remove all the bolts from the differential carrier on the drive shaft side and drop out the rear end unit, be careful it is very heavy and the ring gear teeth can really cut u up.

Sep 29, 2008 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...