Question about Cars & Trucks

1 Answer

Brake Diagram toyta hj61

Unable to back off adjuster on left rear drum

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 130 Answers

Loosen bleeder takes pressure off should be able to remove drum to get to adjuster

Posted on Oct 20, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 740 Answers

SOURCE: 96 Cavalier passenger rear brake lock up when wet or cold

Bad PROPORTION VALVE ... the back brakes should only be doing 30% of the stopping with a bad proportion valve it will send more pressure to the back during braking and cause it to lock up. Good Luck and thanks for using FIX YA

Posted on Jan 04, 2009

handybc70
  • 25 Answers

SOURCE: 05 Equinox not able to remove right rear brake drum

Hiya...
Most rear brake-shoe design take some time to adjust than disc brakes...
If you have a special brake adjustment tool that your local automotive store sells, get this tool and pull out the rubber grommet plug, insert the brake adjustment tool until you 'feel' or hear the sound of 'skipping' on the brake self-adjuster spool inside as you wiggle /adjust the tool inside....(push it inside to get a firm feel that you can 'spin' it)
Try to push the tool downward or upward to check if that'll spin the brake self-adjuster part smaller to allow the brake shoes to 'shrink' which should allow you easy removal of the rear brake drum as you wiggle it out.

Be sure not to breathe in toxic brake dust upon successful brake drum removal.

Posted on Apr 05, 2009

keemo68
  • 1263 Answers

SOURCE: where doe's that spring go on rear brake drums 1996 chevy truck every thing is at top not at bottom, star wheel adjuster?

there should be several springs. first there are (2) real short springs that hold the shoes to the dust cover/back plate. they go in the center of each shoe. then there is a short spring that goes at the bottom where the adjuster is located. there should be a hole in each shoe. finally there is a long spring that goes at the top where your brake cylinder is and this is what gets attched last after your emergancy brake levers are placed between the shoes .

Posted on Apr 17, 2009

frcs68
  • 1605 Answers

SOURCE: left rear wheel locking up. have drum off, need diagram of brakes

back the adjuster to the point you can just trun the caliper or the drum with little force. you will hear a little rubbing sound from the brake pad.

Posted on May 19, 2009

  • 70 Answers

SOURCE: how do I adjust emergency brake cable on 1999 ford

FIRST adjust rear brake starwheel while spinning tire FOWARD. then alongside drivers side of car find emergency brake cable adjustment (long threaded rod with nut) . hold one end of rod with vise-grips and turn nut until emer. brake cable has less slack in it. now go inside car and apply e-brake.you dont want the pedal to stop right away but u also dont want too much"travel" in the pedal.so about halfway is IDEAL. IMPORTANT- once the brake cable is adjusted and the car wont roll foward in gear with the brake on and applying a little "gas"-make sure with brake OFF that rear wheels turn freely. hope this helps.

Posted on Aug 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing rear brakes



REMOVAL & INSTALLATION
It is a good idea to only disassemble and assemble one side at a time, leaving the other side intact as a reference.

  1. Raise and support the vehicle safely.
  2. Remove the brake drum.
  3. Disconnect the parking brake rear cable and conduit.
  4. Remove the brake shoe hold-down springs and brake shoe hold-down pins.
  5. Remove the brake shoe adjusting screw spring.
  6. Remove the brake shoe adjusting lever and adjuster screw.
  7. Remove the brake shoe retracting spring.
  8. Remove the brake shoes from the backing plate.
  9. Remove and discard the parking brake lever clip. Remove the washer.
  10. Remove the parking brake lever from the rear brake shoe.

To install:
  1. Thoroughly clean the backing plate with brake cleaning solvent and dry completely.
  2. Use silicone grease to lubricate the brake backing plate-to-brake shoe contact areas.
  3. Apply a light coating of premium grease to the threaded areas of the adjuster. Turn the adjuster in and out to spread the lubricant. Turn the adjuster all the way down on the screw and loosen one-half turn.
  4. Install the parking brake lever to the rear (secondary) brake shoe with a new clip.
  5. Position the brake shoes on the backing plate and install the brake shoe hold-down springs.
  6. Attach the parking brake rear cable and conduit to the parking brake lever.
  7. Attach the brake shoe retracting spring.

The socket end of the brake adjuster screw is stamped with "R" or "L" to indicate that it is to be installed either on the right (passenger's side) or left (driver's side) of the vehicle. The adjuster nuts can be distinguished by the number of grooves machined around the body of the nut. Two grooves indicate a right-hand adjuster nut and one groove indicates a left-hand adjuster nut. Another way to identify brake adjuster assemblies is to check thread pitch. The right side adjuster assembly has right-hand threads and the left side has left-hand threads. If installed correctly, the brake adjuster assembly will increase in length when the brake shoe adjusting lever is operated.
  1. Install brake adjuster screw in the slots on the brake shoes. The wider slot on the socket end must fit in the slot on the front (primary) brake shoe.
  2. Install the brake shoe adjusting lever on the lever pin.
  3. Install the brake adjusting screw in the slot on the secondary brake shoe and in the slot on the brake shoe lever. The brake shoe adjusting lever should contact the brake adjuster screw.
  4. Adjust the brake shoes.
  5. Install the drums.


ADJUSTMENTS

The drum brakes are self-adjusting and require a manual adjustment only after the brake shoes have been replaced, or when the length of the adjusting screw has been changed while performing some other service operation.
Drum Installed

  1. Raise and support the vehicle safely.
  2. Remove the rubber plug from the adjusting slot on the backing plate.
  3. Insert a Brake Adjustment Tool (D81L-1103-C) or equivalent into the slot and engage the lowest possible tooth on the starwheel. Move the end of the brake spoon downward to move the starwheel upward and expand the adjusting screw. Repeat this operation until the brakes lock the wheels.
  4. Insert a small screwdriver or piece of firm wire (coat hanger wire) into the adjusting slot and push the automatic adjusting lever out and free of the starwheel on the adjusting screw and hold it there.
  5. Engage the topmost tooth possible on the starwheel with the brake adjusting spoon. Move the end of the adjusting spoon upward to move the adjusting screw starwheel downward and contract the adjusting screw. Back off the adjusting screw starwheel until the wheel spins freely with a minimum of drag. Keep track of the number of turns that the starwheel is backed off, or the number of strokes taken with the brake adjusting spoon.
  6. Repeat this operation for the other side. When backing off the brakes on the other side, the starwheel adjuster must be backed off the same number of turns to prevent side-to-side brake pull.
  7. When the brakes are adjusted, make several stops while backing the vehicle to equalize the brakes on both of the wheels.
  8. Lower the vehicle.

Drum Removed
See Figure 2


0900c152800ae432.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: When using a brake adjustment gauge, first measure the inside diameter of the drum (top) and then adjust the brakes shoes to the proper outside diameter (bottom)

  1. Remove the brake drum.
  2. Make sure that the shoe-to-contact pad areas are clean and properly lubricated.
  3. Using a Brake Adjustment Gauge (D81L-1103-A) or equivalent, check the inside diameter of the drum.
  4. Measure across the diameter of the assembled brake shoes, at their widest point.
  5. Turn the adjusting screw so that the diameter of the shoes is 0.030 in. (0.76mm) less than the brake drum inner diameter.
  6. Install the drum.


INSPECTION

See Figure 3


0900c152800ae433.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Measure brake shoe thickness in several places around the shoe
Inspect the brake shoes for wear using a ruler or Vernier caliper. Compare measurements to the brake specifications chart. If the lining is thinner than specification or there is evidence of the lining being contaminated by brake fluid or oil, replace all brake pad assemblies (a complete axle set).

Dec 19, 2010 | 1998 Ford Windstar

1 Answer

Diagram for right rear brake assembly for a 1993 chrylser lebaron


it's a standard leading trailing bendix brake system, small shoe to the front, larger shoe to the rear. The spring are ease. THE springs that look the same go behind the shoes, the biggest spring goes at the top of the brake assembly, and the spring thats medium goes on the bottem. Don't forget the horse shoe clip to the e-brake cable. The adjustment peice goes near the top. Adjust it all the way and spin the drum while you use the mopar adjustment tool to set the e-brake adjust ment. you should get 1/2 to one full rotation before the drum drum stops spinning. don't forget to gravitey bleed your brake (open the rear bleed screws at the same time, then the front).

Oct 16, 2010 | Chrysler LeBaron Cars & Trucks

2 Answers

How to replace the rear break drums on a hyumdai accent gs


Brake Drums-They seem to be fastened with a nut and have bearings that need to be regreased based on the diagram found for replacing the shoes. Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Wheel 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
To Install:
  1. Install or connect the following: 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
    • Wheel
--- Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Wheel 02-04_hyundai_accent_brake_drum.gif

    • Brake drum 02-04_hyundai_accent_rear_brake_backing_plate.gif

    • Shoe hold-down spring
    • Automatic adjuster spring
    • Adjuster lever
    • Shoe adjuster by spreading the shoes
    • Shoe to shoe spring
To Install:
Note: Apply the specified grease to the shoe to backing plate and shoe to anchor plate contact surfaces.
  1. Install or connect the following: 02-04_hyundai_accent_rear_brake_backing_plate.gif

    • Shoe hold down pin
    • Return spring to the push rod while it is shortened
    • Shoe hold down spring
    • Shoe to shoe spring
    • Shoe adjuster by spreading the shoes
    • Adjuster lever
    • Automatic adjuster spring 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
    • Wheel
Note: After assembling the drum components, pull the parking brake lever all the way up several times
prev.gif next.gifprev.gif next.gif

Sep 30, 2010 | 2001 Hyundai Accent

1 Answer

I need a diagram of the rear brakes of a 1997 Intrepid Chrysler-where can I get one>


If the following is not enough then maybe try Alldata.com which generally has more information, but it will cost: REMOVAL & INSTALLATION Chrysler Concorde, New Yorker, LHS Dodge Intrepid Eagle Vision
  1. Remove the rear wheels and brake drums.
  2. Remove the dust cap from the rear hub and bearing assembly.
  3. Remove the cotter pin, nut retainer and wave washer. Discard the old cotter pin.
  4. Remove the rear hub and bearing assembly retainer nut and washer. Remove the rear hub and bearing assembly from the spindle.
  5. Remove the automatic adjuster spring from the adjuster lever.
  6. Rotate the automatic adjuster starwheel enough so both shoes move out far enough to be free of the wheel cylinder boots.
  7. Disconnect the parking brake cable from the actuating lever. Disconnect parking brake cable one side at a time.
  8. Remove the both lower brake shoe to anchor springs.
  9. Remove the 2 brake shoe hold-down springs from the brake shoes.
  10. Remove the brake shoes, upper shoe-to-shoe return spring, automatic adjuster and automatic adjuster lever from the backing plate as an assembly.
  11. Separate the brake shoes from the automatic adjuster mechanism.
  12. Remove the brake shoe automatic adjuster lever from the leading brake shoe. To install:
  13. Thoroughly clean and dry the backing plate. To prepare the backing plate, lubricate the bosses, anchor pin and parking brake actuating lever pivot surface lightly with lithium based grease.
  14. Remove, clean and dry all parts still on the old shoes. Lubricate the starwheel shaft threads with anti-seize lubricant.
  15. Assemble both brake shoes, the top shoe to shoe return spring, automatic adjuster and automatic adjuster lever before mounting on vehicle. Make sure the ends of the automatic adjusters are positioned above the extruded pins in the webbing of the brake shoes prior to installation.
  16. Install the brake shoe assembly onto the brake support plate and install the hold-down springs.
  17. Install the lower anchor springs and reconnect the parking brake cable to the park brake lever of the trailing brake shoe.
  18. Rotate the serrated adjuster nut to remove the free-play from the adjuster assembly.
  19. Install the automatic adjuster lever spring on the lead brake shoe assembly and the automatic adjuster lever.
  20. Install the rear hub and bearing assembly. Install washer and retainer nut and torque to 124 ft. lbs. (168 Nm).
  21. Install the wave washer, nut retainer and a new cotter pin onto the spindle. Install dust cap.
  22. Adjust brake shoes so not to interfere with brake drum installation. Install the rear brake drum. NOTE: After installing the brake drums, pump the brake pedal several times to partially adjust the brake shoes. To verify proper operation of the self-adjusting parking brake, be sure that both rear brakes are not dragging when the parking brake pedal is released.
  23. Install the rear wheels and lug nuts. Torque the lug nuts, in a star pattern sequence, to 95 ft. lbs. (129 Nm).
  24. Road test the vehicle. The automatic adjusters will continue brake adjustment during the road test of the vehicle.
prev.gif next.gif

Sep 03, 2010 | 1997 Dodge Intrepid

1 Answer

Trying but unable to take the rear drums off 2006 chevrolet silverado 2wd 1500 ext cab


According to AutoZone, if you have the full floating axles they have to come off to get the drum off. The semi-floating axles are easier--if you have those you just need to back off the adjuster as I explained. Reach a thin screwdriver into the hole in the back above the axle. It might have a cap over it or a "punch out." You need to turn the star (slightly visible in attached pic) in I think the up direction several turns to get past the lip in the drum. It will resist turning as it ratchets in the opposite direction. You should be able to tell if you're going the right direction as the drum should get looser.




Removal & Installation

Full Floating Axles
To remove the drums from full floating rear axles, the axle shaft will have to be removed. Full-floating rear axles can be identified by a bearing housing that protrudes through the center of the wheel.
  1. Remove or disconnect the following:

    Wheel Axle shaft Retaining ring, key and adjusting nut Hub and drum

To install:
  1. Install or connect the following:

    Hub and drum to the tube Adjusting nut Key and retaining ring Axle shaft and wheel

Semi-Floating Axles
  1. Raise and support the vehicle safely.
  2. Mark the relationship of the wheel to the hub and remove the wheel.
  3. Mark the relationship of the drum to the hub and pull the drum from the brake assembly. If the brake drums have been scored from worn linings, the brake adjuster must be backed off so the brake shoes will retract from the drum. The adjuster can be backed off by inserting a brake adjusting tool through the access hole provided. In some cases the access hole is provided in the brake drum. A metal cover plate is over the hole. This may be removed by using a hammer and chisel.

    0996b43f80203100.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the brake drum

To install:
  1. Align the mark on the drum to mark on hub and install drum
  2. Align the mark on the wheel to mark on drum and install wheel
  3. Adjust brake lining as needed. Pump brakes

Aug 24, 2010 | 2006 Chevrolet Silverado 1500 2WD

2 Answers

I need a diagram for the rear drum brake for 2002 Ford Ranger


Copy and paste this into your search window: 2002 ford ranger rear brake diagram

You should see four pictures pop up, select the brake parts diagram or the brake picture.

Sep 03, 2009 | 1993 Ford F150 SuperCab

1 Answer

Left rear wheel locking up. have drum off, need diagram of brakes


back the adjuster to the point you can just trun the caliper or the drum with little force. you will hear a little rubbing sound from the brake pad.

May 19, 2009 | 2000 Dodge Neon

1 Answer

1999 nissan quest rear brake shoes need changing


help is here:
http://autos.groups.yahoo.com/group/villagerquest/

Drum Removal
  1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .
  1. Retract the brake shoes and loosen the brake adjuster screw.
975565f.gif
  1. Remove the brake drum.
----------------------
May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

------------------------------------------------------------------------------
#10 is access plug to back off adjusting wheel.

f9f31b5.gif
Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

--------------
Shoes Removal

Take a picture and remember how each part goes and attaches
  1. Remove the brake drum, refer to Drum in this section.
  1. Remove the upper retracting spring.
  1. Remove the lower retracting spring.
  1. Remove the self-adjuster.
38bcaa0.gif
  1. Remove the hold-down springs.
  1. Remove the parking brake lever clip and the parking brake lever.

Apr 17, 2009 | 1999 Nissan Quest

1 Answer

I need a schematic for the rear brakes on an F150 super cab with 4.6L automatic trans 4wheel drive


Drum, Rear Brake System Standard Rear Brake
9969082.gif
Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
Heavy Duty Rear Brake
6dcb5d2.gif
Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
The rear drum brakes:
  • Have internal shoes that expand against the brake drum (1126).
  • Are a single-anchor type.
  • Are actuated by one rear wheel cylinder (2262).
  • Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
  • Adjust rear brake shoes and linings (2200) automatically.
  • Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.
When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

Apr 04, 2009 | 1997 Ford F150 Regular Cab

1 Answer

After inserting new rear shoes cant get drum back on


you have to turn the adjusters all the way back in, put the drums on and adjust the shoe tension from the slot in the backing plates with a flat screwdriver or brake drum adjuster tool good luck and please rate -Jeff this will be item "O" in this following diagram please rate
Cilck HERE

Sep 13, 2008 | Mitsubishi Lancer Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...