Question about 2005 Isuzu Ascender

1 Answer

Fan clutch retaining remove - 2005 Isuzu Ascender

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 364 Answers

Use a screwdriver between two of the 4 waterpump nuts while wrenching on the big nut. Possible left hand thread, call the dealership and ask for service department to see if it is L/H thread. hope this helps.

Posted on Oct 20, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the clutch fan on a Isuzu rodeo


no year, engine (size) stated.
on all cars its the same,
gain access to it, (shrouds,etc, depands on how big your arms are.)
off the fan belt. (release tension-er.)
off the fan and clutch replace new clutch to old fan/.
put back
set tension on belt.

the FSM steps for fan off are below (buy the FSM and read it?)
guess 1995...
  1. the fan is first then clutch.
  2. Disconnect the negative battery cable.
  3. Remove the upper radiator shroud and, if desired for additional clearance, remove the radiator from the vehicle.
  4. Although it is not necessary in most cases, the radiator may be removed from the vehicle for easier access to the fan
  5. retainers. If the radiator is left in place, use extra caution to prevent damage to the fragile radiator fins.
  6. Remove the fan assembly attaching nuts (clutch type) or bolts (standard type), then remove the fan assembly from the engine.
  7. Some vehicles use a space between the fan and the water pump pulley. If used, be sure to retain the spacer for
  8. installation.
  9. If necessary, the clutch may be removed from the fan by removing the attaching nuts or bolts (as applicable).
  10. end remove.

Nov 12, 2015 | Isuzu Cars & Trucks

1 Answer

HOW TO REPLACE CLUTCH FAN


to remove clutch fan you need to remove upper fan shroud, you need large wrench to remove the fan clutch retaining nut to remove fan and clutch away from the engine drive belt should keep pulley from turning while loosen fan clutch retaining nut.if pulley belt turns while loosen fan clutch bolt remove drive belt use strap wrench hold pulley while you remove fan clutch bolt this procedure for checvrolet if you working on volkswagon you need spanner wrench hold the idler pulley while you use large wrench to loosen the large drive nut to fan clutch. you have to remove fan with clutch from engine then you can remove clutch from fan you can go to auto parts stores rent a spanner wrench try auto zone they rent out tools.

Jan 05, 2012 | Cars & Trucks

1 Answer

How replace fan belt for Ford Crown Victoria 2000?


Mechanical Fan Belt Removal & Installation - Refer to Illustration below


Ford 4.6L Engine - Ford Crown Victoria, Mercury Grand Marquis, Lincoln Town Car, Marauder

1. Loosen the fan clutch-mounting shaft from the water pump hub.

2. Loosen the fan shroud from its radiator mounting and remove the lower hose from the shroud.

3. Lift the fan and clutch assembly and the fan shroud from the vehicle.

4. If necessary, remove the fan-to-fan clutch retaining bolts and separate the fan from the fan clutch.




CAUTION
Closely examine the fan for cracks or separation, to avoid the possibility of personal injury or vehicle damage.

To install:

1. Assemble the fan and fan clutch. Tighten the retaining bolts to 15-20 ft. lbs. (20-27 Nm).

2. Install the fan and clutch assembly and the fan shroud. Mount the fan clutch shaft to the water pump hub and tighten to 37-46 ft. lbs. (50-62 Nm).

3. Slip the shroud into the lower mounting clips and install the shroud retaining screws.

Fig. 1

archaeology_79.jpg

To view this JPEG image better, you can Right-click on it, "Save Image As..." then
view it or enlarge it within Microsoft Windows Media Player, or Real Networks RealPlayer.

Sep 04, 2011 | 2000 Ford Crown Victoria

1 Answer

Trying to remove fan clutch,which way does it turn?


YOU NEED TO HOLD FAN CLUTCH WITH A CLUTCH TOOL THEN LOOSEN THE LARGE NUT RETAINING THE FAN AND CLUTCH ASSEMBLY REMOVE FAN TO CLUTCH BOLTS AND NUTS COUNTERCLOCK WISE.

Apr 01, 2011 | 2000 Chevrolet S-10

1 Answer

I need to remove the cooling fan shroud from my 1995 Lincoln Continental. How is the easiest way to go about this?


Engine Fan REMOVAL & INSTALLATION 3.8L Engines
  1. Disconnect the negative battery cable.
  2. Remove the radiator upper sight shield.
  3. Disengage the electrical connector, then remove the integrated relay control/constant control relay module assembly located on the radiator support.
  4. Disconnect the fan electrical connector. Fig. 1: Disengage the fan electrical connector 86873115.jpg

  5. If necessary, remove the air bag crash sensor.
  6. Unbolt the fan/shroud assembly from the radiator and remove. Fig. 2: Unbolt the fan assembly from the radiator 86873116.jpg
    Fig. 3: Remove the fan from the engine 86873117.jpg
    Fig. 4: Slide the fan as an assembly up and away from the radiator. Be careful not to dislodge the mounting stud on the left side. 93143p56.jpg

  7. Remove the retainer and the fan from the motor shaft and unbolt the fan motor from the shroud.
  8. Installation is the reverse of the removal procedures. Tighten the fan shroud retaining bolt to 23–33 inch lbs. (2.6–3.7 Nm). Tighten the fan shroud retaining nut to 71–106 inch lbs. (8–12 Nm). Fig. 5: Constant control relay module location — 3.8L engines 86873118.gif
4.6L Engine
  1. Loosen the fan clutch-mounting shaft from the water pump hub.
  2. Loosen the fan shroud from its radiator mounting and remove the lower hose from the shroud.
  3. Lift the fan and clutch assembly and the fan shroud from the vehicle.
  4. If necessary, remove the fan-to-fan clutch retaining bolts and separate the fan from the fan clutch. CAUTION
    Closely examine the fan for cracks or separation, to avoid the possibility of personal injury or vehicle damage. To install:
  5. Assemble the fan and fan clutch. Tighten the retaining bolts to 15–20 ft. lbs. (20–27 Nm).
  6. Install the fan and clutch assembly and the fan shroud. Mount the fan clutch shaft to the water pump hub and tighten to 37–46 ft. lbs. (50–62 Nm).
  7. Slip the shroud into the lower mounting clips and install the shroud retaining screws. Fig. 6: Fan and fan clutch assembly — 4.6L engine 84173064.jpg
5.0L Engines
  1. Loosen the fan clutch-to-water pump hub retaining bolts.
  2. If necessary, remove the drive belt from the water pump pulley.
  3. Remove the fan shroud upper retaining screws. Lift the shroud to disengage it from the lower retaining clips.
  4. Remove the fan clutch-to-water pump hub bolts and remove the fan and clutch assembly and the fan shroud.
  5. If necessary, remove the fan-to-fan clutch retaining bolts and separate the fan from the fan clutch. CAUTION
    Closely examine the fan for cracks or separation, to avoid the possibility of personal injury or vehicle damage. To install:
  6. Assemble the fan and fan clutch. Tighten the retaining bolts evenly and alternately to 12–18 ft. lbs. (16–24 Nm).
  7. Install the fan and clutch assembly and the fan shroud.
  8. Install the fan clutch-to-water pump hub bolts.
  9. Slip the shroud into the lower mounting clips and install the shroud retaining screws.
  10. If removed, install the water pump drive pulley and adjust the belt tension; refer to Section 1.
  11. Tighten the fan clutch-to-water pump hub bolts evenly and alternately to 15–22 ft. lbs. (20–27 Nm). Recheck the belt tension.
prev.gif next.gif

Jul 14, 2010 | 1995 Lincoln Continental

1 Answer

How to remove a water pump


Locate water pump.. It's where the bottom radiator hose goes from the radiator. Remove any brackets or parts that are in your way. Remove water pump! Reverse procedure for installation. You have to remove the fan clutch from the water pump shaft and lift the shroud, fan and clutch all out together. remove two bolts in the center radiator support which let the radiator move forward an inch or so, loosen the fan from the clutch for a little more wiggle room to get it out. The shroud will have rubber splash shields hooked to the lower sides too, so be sure to unhook them or you will tear out the holes in the rubber shields.The fan clutch has to come off anyway because it's attached to the water pump. You don't need to remove the fan shroud. Just take out two bolts on the fan clutch and loosen the other two so you can push the clutch back a little (DON'T let the fan clutch fall). Then remove the water pump. It's a little tight, but much easier than removing the fan shroud.the only specialty tool that you will need is the water pumpt "grab" tool and the fan clutch wrench. These two items come together in one kit that you can rent from the Auto Parts store.
The "grab" tool holds the water pumpt pully firmly while you rotate the fan clutch retainer using the fan clutch wrench.

DO NOT attempt to use a break over bar or some other home-grown tool to hold the water pump pully while attempting to break the fan clutch free - you will mess up the heads of the four retainer bolts holding the pully to the water pump face.
this will help.thanks.

Feb 21, 2010 | 2006 GMC Envoy

1 Answer

How to take off the cooling fan from 1997 gmc safari


  1. Disconnect the negative battery cable for safety.
  2. Place a catch pan under the radiator, open the drain **** and drain the cooling system.
  3. Loosen the clamp, then remove the air cleaner assembly.
  4. Remove the upper fan shroud retaining bolts, then remove the upper shroud from the vehicle.
  5. Remove the fan and clutch assembly retainers using J-41240, or an equivalent fan clutch wrench.
  6. If necessary, remove the 4 bolts holding the fan blade to the clutch, then separate the fan from the clutch assembly.

    Installation is the reverse of the removal procedure. Tighten the components to the following specifications:
you will need a special tool to remove #3 fan clutch.

952faac.gif
the tool is sold in pep boys auto zone and many auto parts.

Sep 09, 2009 | 1997 GMC Safari

1 Answer

How to remove the fan clutch on a 6.0 diesel


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove the air cleaner assembly.
  4. Disconnect the radiator upper hose from the radiator. Position the radiator hose aside.
  5. Disconnect the overflow hose from the radiator.
  6. Disconnect the coolant degas bottle hose from the shroud.
  7. WARNING The clutch assembly nut has a right-hand thread and must be rotated counterclockwise to remove it.31a3ca2.gif
  8. 95f52a2.gifUsing the special tools, loosen the fan clutch.
  9. Carefully rotate the fan and fan clutch assembly counterclockwise until the assembly is free from the water pump. Place the fan and fan clutch into the shroud opening.
  10. If equipped, disconnect the retaining clips from the fan shroud.
  11. Raise and support the vehicle.
  12. Disconnect the lower radiator hose retaining clamp from the shroud.
  13. If equipped, disconnect the underbody splash shield from the shroud.
  14. Lower the vehicle.
  15. WARNING Use extreme care when removing or installing the fan, fan clutch and shroud. Failure to do so will cause damage to the radiator.
  16. Remove the mounting bolts, and the fan, fan clutch and shroud.
  17. To install, reverse the removal procedure. Install an appropriately sized worm drive-type clamp in place of the constant tension clamp. Observe the tightening torques shown in the accompanying illustrations.

Jun 20, 2009 | 2005 Ford E-Series

1 Answer

Need to take off fan clutch, have taken off parts in the way


4.9L SFI
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding Tool T84T-6312-C Fan Clutch Nut Wrench T93T-6312-B
Removal
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The large clutch assembly nut has a right-hand thread and must be rotated counterclockwise to remove it.
    Remove the fan clutch (8A616) from the water pump (8501) by turning the large nut, which is part of the fan clutch, using Fan Clutch Holding Tool T84T-6312-C and Fan Clutch Nut Wrench T93T-6312-B.
  1. Remove two screws retaining fan shroud.
  1. Remove the fan blade (8600), fan clutch and shroud.
  1. If the fan blade and fan clutch have to be separated, remove the remaining bolts attaching the fan blade to the fan clutch
b098d2e.gif


5.0L, 5.8L and 7.5L Engines
Removal
  1. Remove screws retaining fan shroud (8146) to radiator (8005).
  1. Remove four screws retaining clutch on water pump hub.
  1. Pull fan clutch and fan blade off water pump pilot and remove fan clutch, fan blade and shroud from vehicle.
  1. Remove four screws and separate fan clutch from fan blade.
4d17f8c.gif

Item Part Number Description 1 8509 Water Pump Pulley 2 57632-S Screw and Washer Assembly, 5/16-18 x .62 Hex 3 8600 Fan Blade (5.0 and 5.8L) 4 8600 Fan Blade (7.5L) 5 8A616 Fan Clutch 6 380288-S2 Screw and Washer Assembly, 5/16-24 x .88 Hex A — 16-24 Nm (12-18 Lb-Ft)

Mar 10, 2009 | 1994 Ford F150 Styleside Supercab

Not finding what you are looking for?
2005 Isuzu Ascender Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...