Question about Cars & Trucks

Open Question

How do I replace an alternator on a 2008 scion xb

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 255 Answers

SOURCE: scion xb wont start

Hi.. Yes i fix my problem by disconecting the neutral suitch and reconecting it ,,they get dirty with time and dont make contact ,Is a good idea to disconect and clean as many contacts as you can and put some special grease on them to prevent other problems ...

Posted on Jul 29, 2008

  • 101 Answers

SOURCE: need help to remove 2005 Scion xB water pump

1st ...that should be covered under 6 year 50k power train warranty from the dealer.
But if your over....you need to unbolt the right side motor mount (on the water pump side) and lift the engine some with a floor jack to get clearance,

Posted on Apr 11, 2009

  • 439 Answers

SOURCE: How d you replace the starter on a 2005 Scion xb?

There are two bolts, one is at the top exactly opposite of the first one you took out. You will not be able to see it, but feel around the head of the starter where it goes into the block and you will feel where it goes.

Posted on Jun 23, 2009

  • 38 Answers

SOURCE: How do I install alt. belt on 2005 scion xb?

I just looked at my '04 xB. It looks very straight forward.
loosen the bolt that holds the alternator to the bracket.
carefully slide the alt to the bottom. (Also be aware of the plug and wires on the alt.They should never hold the weight of the alternator. You dont want them breaking prematurely.)
Pull the belt off, remove the belt from the crank shaft pulley.

Do the reverse, and you will have replaced the belt.

Make sure to check the belt in about a week or so.
New belts will stretch over time. Make sure you keep the tension tight enough to work correctly, but not so tight that the alernator shaft is warped.
I usually place the new belt on both pulleys and give a good "medium" pull on the alt while tightening. Find the middle of the belt and squeeze them together, depending on the type and length of the belt, there should be about 1/4" of flex on both sides.

Posted on Jun 29, 2009

  • 1 Answer

SOURCE: 2006 scion xb 100,000 mile what kind of maintenance do i need??

I would recommend getting the transmission serviced, and the antifreeze changed.

Posted on Aug 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remote starter only allows my starter to turn over twice; needs at least 3 with my key. How to adjust to have it starter run longer on remote?


I know you are looking to have the remote starter run a third time but I would say you need to look at your Fuel Pressure Regulator on the Scion. Sounds like it is not holding fuel pressure at the fuel rail and that is why it requires a third Crank

Jan 05, 2016 | 2006 Scion xB

1 Answer

Where is the lighter fuse on a Scion xB 2008


Check you drivers manual it will show where the fuse is located and give the correct fuse to replace.
Posted on Dec 03, 2015

Feb 26, 2015 | 2008 Scion Xb

1 Answer

How do i change wheel hub assembly on scion xb?


You need an impact wrench and large socket to get the spindle nut off, also some use star pattern bolts to hold on the hub. Will require a torque wrench also for re install. Some models require separating the ball joints too, a spreader is helpful. Not a job for anyone without good tools and a good bit of mechanic experience.

Jul 17, 2014 | 2008 Scion Xb

1 Answer

I can not find the 50 amp heater fuse on my 2008 Scion XB


its one of the big square ones. or its missing.

Aug 03, 2012 | 2008 Scion Xb

1 Answer

How do you fix code po717 on a 2008 scion xb ?


Code is for a speed sensor in the transaxle. You could have it replaced or tested.

Jul 02, 2012 | 2008 Scion Xb

1 Answer

Can't get the pivot bolt on my '05 scion xb's alternator to break


undo the lock on the tensioner.for the other bolt,use what is known as a breaker bar,some oaf probably used an air gun to tighten the bolt,not a torque wrench. a breaker bar will give up to 300 lb feet of torque.

Sep 06, 2009 | Scion xB Cars & Trucks

1 Answer

How do I reset the speedometer in my scion xb. It


Legally you can't.
All service to this system must be conducted by a licensed repair shop.

Aug 24, 2009 | 2008 Scion Xb

1 Answer

Remove 08 Scion XB Navigation


The trim around the stereo and center vents pulls straight out. It is held in by plastic reusable clips. No tools needed.

Mar 23, 2009 | 2008 Scion Xb

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...