Question about 2005 Ford Focus

1 Answer

What is the proper tires position when rotating them?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 77 Answers

Here ya go, hope it helps!

What is the proper tires position when rotating - d308ec3e-5f98-4e83-932f-d9037acde2a5.jpg

Posted on Oct 19, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Numbers for tire rotation sequence


The rotation can only be from back to front on same side of car only. They found crisscrossing is bad because of the way the tread patterns wear.

Oct 19, 2014 | Lexus GX 470 Cars & Trucks

1 Answer

1999 suburban runs rough on passenger side


Usually a bad tire or wheel alignment due to worn ball joints , sway bar, or other steering components. Try rotating the tires and see if the roughness moves position. Also check for unusual wear on the tire and proper inflation.

Jul 17, 2014 | Cars & Trucks

1 Answer

Instrument panel says check rt rear tire pressure. Yellow light on. Pressure fine. How do I reset? 2008 gmc 2500 he crew


The sensor is a part of the valve stem. It is a radio..powered by a battery. The battery may be dead, requiring a new sensor. Also possible that your tires have been rotated and the shop did not reprogram each sensor to the proper wheel position. Check your other tires first, then go to a shop that can test that all sensors are functioning properly.

Nov 20, 2013 | Cars & Trucks

1 Answer

Message Warning - Tire Pressure System Maintenance Required - Does this mean a sensor is out as I have checked tire pressure to ensure 34 lbs. pressure in each?


If you've had the tires rotated or installed new tires recently they may have installed the wrong wheel in the wrong location. This can cause false readings from the tire pressure sensor readings. Make sure the wheels are in the proper position on the vehicle.

Mar 23, 2011 | 2001 Volvo S60

1 Answer

I cannot take the tire and rim off the car. Is there a tool that must be used to do so?


Once you remove the wheel nuts the tire assembly should literally fall into your arms.If it isn't moving you are going to have to resort to brute force.With the vehicle properly supported kick the tire at the 12 o'clock position (hard),rotate the tire 90 degrees and kick again,etc.Sometimes the rust deposit between the rim and the wheel stud is so bad it seems like the tire is welded on.Keep at it and good luck.

Oct 22, 2010 | Oldsmobile Alero Cars & Trucks

1 Answer

I can't get the spare tire out of the rack? 2004 yukon


  • Rotate the hoist shaft counterclockwise in order to lower the spare tire to the ground. Continue to rotate the shaft until the spare tire can be pulled out from under the vehicle and removed. If the spare tire does not lower to the ground, the secondary latch is engaged causing the tire not to lower.
  • If the secondary latch is engaged and the cable end is visible, perform the following procedure: 3.1. Tighten the cable by rotating the hoist shaft clockwise until you hear 2 clicks or feel it skip twice. You cannot overtighten the cable. 3.2. Loosen the cable by rotating the hoist shaft counterclockwise 3 or 4 turns. 3.3. If the spare tire can be lowered, repeat steps 1 and 2 to see if the spare tire can be removed. 3.4. If the spare tire cannot be lowered, rotate the hoist shaft counterclockwise until approximately 15 cm (6 in) of cable is exposed. 3.5. Raise and support the vehicle. 3.6. Place a transmission jack, or equivalent, under the spare tire. 3.7. Position the center of the transmission jack under the secondary latch release button at the center of the spare tire. Arrange the arms of the transmission jack so they will support the tire after it has been released. 3.8. Raise the jack until the spare tire stops moving upward and is firmly held in place, releasing the secondary latch. 3.9. Lower the tire. If the spare tire is hanging by the cable, rotate the hoist shaft counterclockwise until the tire is low enough to remove.
  • Feb 28, 2010 | 2009 GMC Yukon XL

    1 Answer

    What is the proper sequence for rotating tires?


    My understanding is that with radial tires that are in use today, you should rotate front to back on same side. Not side to side.

    Jul 09, 2009 | 2005 Dodge Neon

    1 Answer

    Service tire system, what does that mean???


    Well, it might simply mean they wish to rotate your tires. When you are told your tires need to be rotated, it means your tires are warn on certain parts. You can get quite a few more miles out of the tires if you simply rotate, or move the front right to another place on the car, and change the rest of the tires positions as well.

    They might also want to just check to see how warn they are in general, but their likely going to rotate, and align your tires.

    Apr 16, 2009 | Chrysler Pacifica Cars & Trucks

    2 Answers

    Tire rotation warning


    It has nothing to do with rotating your tires, on your LCD screen when you select maintenance, you can select at how many miles you want to be reminded when to change your oil and when to rotate your tires. Once your vehicle has reached so many miles it'll pop up to remind you as it's sposed to do. While at a stopped position go to that screen, scroll down with your little joystick type knob and when you've selected tire rotation, you click to reset the miles on it back to zero. When you do your oil change you do the same thing. Your screen doesn't know if you've changed your tires or not, only you can tell it that you have.

    Dec 06, 2008 | 2004 Nissan Murano

    Not finding what you are looking for?
    2005 Ford Focus Logo

    20 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    fordexpert

    Level 3 Expert

    5546 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...