Question about 2004 Chrysler Pacifica

Open Question

Oil switch sensor location 04 pacifica - 2004 Chrysler Pacifica

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 67 Answers

SOURCE: WHERE IS THE OIL PRESSURE SWITCH LOCATED IN MY

just above the a/c compressor pully and to the left

Posted on Nov 12, 2009

  • 1 Answer

SOURCE: location of map sensor on 04 chrysler pacifica

Sensor is located passenger side of the intake and mounts facing the firewall .It takes a torx bit to remove .NOT a philips as screw is hard to see from the front.I use a bit with a 1/4 in socket as a full size screwdriver will not fit.Remove screw and use a set of pliers to twist and pull back.

Posted on Mar 24, 2010

Mustang_Guru
  • 85 Answers

SOURCE: Looking for a diagram for the left side of my

#1 below:


mustang_guru_1.jpg
Best wishes!

Posted on Jan 05, 2011

  • 1 Answer

SOURCE: crankshaft position sensor location on 2004 chrystler pacifica

can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

Posted on Apr 25, 2011

chargerhp
  • 813 Answers

SOURCE: need 04 pacifica transmission range sensor diagram

Its on the side of trans facing radiator bottom center

Posted on Jan 03, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

P0420 p0522 chrysler pacifica CODES


thje po420 need to monitor o2 sensors to verify if you have a bad sensor or bad catalitic converter
the po522 oil presure sending unit

Oct 15, 2014 | 2005 Chrysler Pacifica

1 Answer

I have an 04 Chrysler pacifica and my key is stuck in the ignition


slam it into park,sounds like shift interlock is hanging up or disconnect the cable at the shifter then try it

Oct 12, 2014 | 2004 Chrysler Pacifica

1 Answer

Oil pressure switch location 04 crysler pacifica 3.5


It is impossible to replace have the dealer do it for 85 dollars. It is just above the oil filter between two other things and it is easy to replace if you rip the connector off instead of taking it off right. It took a repair shop 6 hours to replace it when I couldn't and it cost me 70 dollars money well spent. They told me 15 minutes

Apr 02, 2014 | 2004 Chrysler Pacifica

1 Answer

How do I change the oil pressure switch in a 2004 Chrysler Pacifica


most likely not the sensor; change the oil and use an oil of greater viscosity. which engine? how many miles?

Mar 05, 2013 | 2004 Chrysler Pacifica

2 Answers

Where is the map sensor located on the pacifica


The MAP sensor on the Chrysler Conquest is located either on the passenger side or the driver side down around knee level. The Manifold Absolute Pressure sensor (MAP sensor) is one of the sensors used in an internal combustion engine's electronic control system.-------------------------------------------------------------------------------------
Car Key Programmers

Nov 27, 2012 | 2004 Chrysler Pacifica

1 Answer

My 04 pacifica radio, heater, dvd won't play, no


Check your relays the accessory relay right hand upper corner and the run relay middle left side if they are the same relay switch them and see if that works if not could be the body control module. Realys under hood to the right of the battery

Nov 13, 2011 | 2004 Chrysler Pacifica

1 Answer

Location of map sensor on 04 chrysler pacifica


Sensor is located passenger side of the intake and mounts facing the firewall .It takes a torx bit to remove .NOT a philips as screw is hard to see from the front.I use a bit with a 1/4 in socket as a full size screwdriver will not fit.Remove screw and use a set of pliers to twist and pull back.

Jun 21, 2009 | Chrysler Pacifica Cars & Trucks

3 Answers

Crankshaft position sensor location on 2004 chrystler pacifica


can u please tell me where on my 2004 chrysler pacifica is the crankshaft sensor located?

May 02, 2009 | Chrysler Pacifica Cars & Trucks

Not finding what you are looking for?
2004 Chrysler Pacifica Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...