Question about 1999 Dodge Ram

Open Question

Socket size for rear pinion yoke on 1997 dodge ram 1500

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 1997 dodge ram 1500 v6,i have a misfire,ive changed plugs,wires,distributor cap,rotor cap,fuel pump,rollover valve,coil,still has a miss

you can try changing the ignition coil, I own a 97 Dodge 1500 and mine did the same and thats what i had to do.

Posted on Oct 08, 2008

Ad
  • 599 Answers

SOURCE: Seized rear brake drum on a 1997 Dodge Ram 1500

loosen emergency brake both sides..open wheel cylinder and let fluid run as you pry gently side to side in between drum adn shoe through backing plate /drum area to collapse the shoes some..... use wd40 or quality rust buster at center of drum /axle area to loosen grip of rust fused metal at hub to drum ..tap tap with hammmer around circumference of drum to dislodge adn loosen shoes from drum and drum from axle..good luck.. be patient work slowly

Posted on Nov 11, 2008

  • 512 Answers

SOURCE: Pinion Bearing

the only way to replace pinion bearings is to remove the differential. you shouldnt have to remove the bearing to replace the seal

Posted on Nov 18, 2008

emissionwiz
  • 76848 Answers

SOURCE: 1997 Dodge Ram 1500 transmission will a 1996 interchange

No, the frame is different.

Posted on Nov 30, 2008

fgainer
  • 54 Answers

SOURCE: 2004 dodge ram 1500 rear brake light out how to replace?

Open up the tail gate, you will see two torque screws on the inside beside the tail lights. take these out, this will free up the housing and you can change it from there.

Posted on Feb 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2000 ram 1500 4WD v8 5.9l auto. Need to change refer ring and pinion. Dose the teeth of ring and pinion should be same ront and refer?


NO--- Check Gear Ratio On Tag Or Tube--Front and Rear Are Not The Same. Or Count Teeth On Pinion And Ring Gear--Divide Pinion Number Into Ring Gear Number For Ratio.

Feb 17, 2015 | 2000 Dodge Ram 1500 Truck

1 Answer

06 Dodge Ram 1500 4x4 transfer casing cracked around output to rear driveshaft. This has happened twice within 1000 miles


you either have
a broken trans mount
a rear axle twisting
incorrect pinion angle
damaged drive shaft

Oct 27, 2014 | 2006 Dodge Ram 1500

1 Answer

What size socket is needed to remove rear pinion nut on 1997 jeep grand Cherokee limited with a5.2 v8


the rear axle front pinion DANA 44 or AMC?
the answer is not simple , why not read the FSM and unstand it all.
experpted....
  1. On 1990-98 models, set bearing preload as follows:
    1. The required pinion gear bearing preload torque is 1/2 ft. lbs. over the noted release torque as measured above.
    2. Rotate the pinion gear three or four times with a torque wrench attached to the yoke nut. Measure the amount of torque necessary to rotate the pinion.
    3. Using a holding tool, tighten the yoke nut in small increments and remeasure until the specified torque is obtained.



$15
alldata.com
or
free
here
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service
see diff chapters. its non trivial.

Oct 01, 2014 | 1997 Jeep Grand Cherokee

1 Answer

I have a 2003 Dodge Ram 1500 4x4. When the truck slows to a stop, and just as it stops, there is a very loud grinding noise that comes from the rear of the vehicle. I checked underneath and there is fluid...


The fluid splattered all over is most likely coming from the pinion seal. (The seal at the front of the differential where the driveshaft yoke goes in.) Normally, you would remove the driveshaft and the pinion yoke to relace the seal. The grinding however, leads me to believe that the seal leaking is a RESULT not a CAUSE of your problem. The way you describe it sounds like you may have some serious pinion and/or ring gear damage inside the differential.
If this is the case, there are severl ways to go about repairing this. You could tear your differential apart and replace the defective/damaged parts inside. You could replace your differential with a used one from a salvage yard. You could replace your differential with a remanufactured differential assembly.

To check for damage, remove the rear cover from the differential and check for metal in the oil and in the bottom of the housing. You can also turn the ring gear around and check for broken teeth. You can also inspect the spider gears and pinion gear for damage.


















dttech_62.gifdttech_64.gif

Apr 30, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

I need 2004 dodge ram 1500 rear pinion nut torque rating, ...


you need to know what rear end you have if it's a 8.25, 8.37, or 9.25 the pinion nut torque is a minimum of 210 ft. lbs.


if you have the Dana model 44 190-290 ft. lbs.

if you have a Dana model 60 215-315 ft. lbs.

Apr 27, 2011 | 2004 Dodge Ram 1500

1 Answer

2003 dodge ram 1500 4x4,vibration rear wheels ,when taking off in a slow turn,something in the rear end ,its not the brakes,something with the pinion gear i think,how do i fix it


Check your u-joints first. If it is not the u-joint, then it is probably the yoke. Take the driveshaft off/out and on the yoke you will see a nut, make sure that it is tight. You will want to drain and refill your rear end gear oil as well.

Apr 09, 2011 | 2004 Dodge Ram 1500

2 Answers

Cannot find egr valve on my 97 ram 1500


Under hood, center, rear engine area, mounted on rear passenger side of engine im guessing i would need to know what engine?this is based v8 5,2 2 wheel drive

Feb 08, 2010 | 1997 Dodge Ram 1500 Club Cab

2 Answers

My 1995 Dodge Ram Has a Lot of Play in the rear


Bearings. seals ,gaskets, crush sleeve, diffy. fluid and possibly ring gear and pinion .

Jun 29, 2009 | 1995 Dodge Ram 2500

Not finding what you are looking for?
1999 Dodge Ram Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...