Question about 1998 Ford Ranger

1 Answer

1998 ford ranger repair manual for the abs brake system

The problem that I am having is that I have replaced the brake booster, master cylinder, a brake line, rear drum brakes, and the calipers in the front of this 1998 Ford ranger 2 wheel drive and have bleed them and there is still not brakes.... please help..... I am at my wits end on this problem....

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If the brakes work but you have to push very hard, try checking the vacuum supply to the brake booster with the engine running.

Posted on Oct 19, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
little_shaws
  • 493 Answers

SOURCE: no pressure in brakes replaced master cylinder power booster brake lines bled system still no pressure could I have bought defective master? Love my t-bird but can't drive it -all this started wit

Have you checked your rear wheel cylinders for leaking into the drum?

Posted on Jun 04, 2012

Autotroubles
  • 987 Answers

SOURCE: 1999 Ford E350 van problem:

Good question, on the antilock system is a bleader too and bleade it the same way you bleade the caliper. After all is done adjust the rear brakes, they should have a drag to them.

Posted on Feb 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Install master cylinder on 1993 ford ranger


Check that the master cylinder push rod is disconnected from the brake petal under the dashboard.

Jun 01, 2014 | 1988 Ford Ranger

1 Answer

Abs brake system


Best case scenario bad vacuum pressure to the brake booster. Worst case bad abs control module or valve body/motor the abs system works by add and removing hydraulic pressure through valves and electric motor. Try using block off plugs at the master cylinder( remove lines plug outlets at master cylinder) check if brake pedal position and pressure is good(if there is no change problem is master cylinder or brake booster/ vacuum) if plugging at master cylinder solved issue repeat procedure at abs valve body after reinstalling lines from master cylinder if your problem returns your issue is in the abs valve body if plugging at the abs solves problem reconnect at the valve body bleed each line one by one testing between each line until you find the problem

Apr 11, 2014 | Hyundai Cars & Trucks

1 Answer

I have a 1998 Ford Explorer Sport. I have


my friend , it is the problem of the brake boosters, it is between the brake pedal and cylinder , try to change a new one. check here for information: http://www.fiverhope.com , and you have to check your booster type, single vacuum booster or dual vacuum booster

Sep 16, 2013 | Cars & Trucks

4 Answers

I have an 06 jetta, 2.5l. does not have electronic parking brake. the brakes on all 4 wheel are dragging. you can open any bleeder and get a little squirt. wheels will spin freely. when you drive it again...


SOUND LIKE FAULTY ABS UNIT AND WHEEL SENSORS OR MASTER CYLINDER.THE MASTER CYLINDER PISTONS NOT RETURNING.RAISE THE REAR OF VECHICLE BLOCK FRONT WHEELS FROM MOVING.MAKE SURE PARKING BRAKE IS FULLY RELEASED SO YOUR BRAKE BRAKES NOT DRAGGING.THE BACK WHEELS SHOULD TURN WITH BRAKE RELEASED.IF NOT PARKING BRAKE NEEDS ADJUSTMENT.

Oct 29, 2010 | Volkswagen Jetta Cars & Trucks

1 Answer

Abs is still on. i have new pads and master cylinder.


The ABS system is separate from the normal braking system (pads, rotors, master cylinder, etc.). It's essentially a computer that pumps the brakes during heavy braking to prevent, or at least reduce the possibility of a skid. The ABS system needs to be tested and repaired by a qualified mechanic.

Bill B

Aug 06, 2010 | 1998 Ford Contour

2 Answers

Having trouble with the brakes on my '90 Ford ranger. Replaced the master cylinder and still have very little braking power. Any help would be appreciated!


***Seek out professional help this vehicle is not safe to operate.***


Check the vacuum line going to the brake booster.

This is the big round chamber behind the master cylinder.

Hope this tip helps.

R/
David

Jan 23, 2010 | 1990 Ford Ranger SuperCab

1 Answer

Ford Ranger 1994 breaking system just stopped working. No tension on pedal and on checking no brake fluid.


2 places to check 1. look at the rear wheel backing plates for moisture 2. pull the master cylinder back and look for fluid in the vacuum booster. if leaks at the rear its going to be rear wheel cylinders which will require replacing wheel cylinders and shoes. if the vacuum booster is full replace the master and booster.

Dec 28, 2009 | 1994 Ford Ranger Supercab

2 Answers

How do i change manual to power brakes on 1988 ford ranger


Not sure exactly but I love to do stuff like this. First thing I would do is go to a salvage yard and rob the pieces form another truck with power brakes. You know you need the booster and the master cylinder, but you might also need the pedal and the pedal bracket. All the lines and the combo valve and calipers and wheel cylinders should be fine.

Jun 28, 2009 | 1988 Ford Ranger

1 Answer

Replacing my brake booster


go to the master cylinder and remove it from the booster, disconnect the vacuum line from the booster, then disconnect the brake plunger from your brake pedal inside the vehicle, then remove the booster mounting bolts from inside the vehicle then remove the booster, install in reverse order, once you install the master cylinder, you will need to bleed out any air in the brake system, hope this helps, let me know

May 16, 2009 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
1998 Ford Ranger Logo

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...