Question about 2000 Isuzu Rodeo

Open Question

How to reset the ABS light on 2003 Isuzu Rodeo

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: how to change oil transmission isuzu rodeo 2003

There are two drain plugs on the bottom of the pan. remove the lower one to drain the trans fluid. To refill, use a pump and pump the fluid into the upper drain plug until it seeps out and re-install the plug, similar to refilling a manual trans.
Once this is done, Start the vehicle and run it for about 3 minutes, shifting through all gears (do not drive vehicle Remove the upper drain plug and let any excess fluid drain out. Done. This is as per Mitchell OnDemand.

Posted on Aug 14, 2008

Ad
  • 1 Answer

SOURCE: Isuzu Rodeo abs light

I had it repaired: one of my sensors needed to be replaced. No more light!

Posted on Nov 23, 2008

baccardo
  • 150 Answers

SOURCE: reduce power and check engine lights on

reduced power usally points toward a gas pedal to throttle correlation meaning the drive by wire system is where the problem is

Posted on Apr 18, 2009

  • 6 Answers

SOURCE: Were is my ABS sensor located on my 2000 Isuzu Rodeo

there should be a sensor at all 4 wheels so make sure there all pluged in 

Posted on Jul 04, 2009

alicantecoli
  • 22219 Answers

SOURCE: 2002 ISUZU RODEO SE ABS LIGHT IS ON, WHY?

last question as my back hurts from sitting on computer ,right first lift each wheel up and check the wires to the sensors on the wheels ,their is a metal ring with teeth on and what often happens is the wire breaks to the sensor or the metal ring comes loose on the shaft and just spins around .Try this first before you go to a garage who would weld the ring up and charge you for a new computer or something

Posted on Jun 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have Isuzu Rodeo 2003 and problem with 4wd, it doesn't work and the light is on. I Suppose the problem is the black box (under armrest) but I can't find it. Where from can I buy it?


The black box you have says abs that's for your brakes. My four wheel drive done the same thing it was a vacuum solenoid located on the front axel had about six or 8 vacuum hoses going to it I got one out of a junk yard.

Mar 12, 2015 | 2003 Isuzu Rodeo

1 Answer

Hew many speed sensors does a 2001 isuzu rodeo have, what do they look like, and where are they located?


best is to have your vehicle scanned. it might be a faulty wheel sensor.

Sep 11, 2014 | 2001 Isuzu Rodeo

1 Answer

How reset check 4wd light for isuzu rodeo 2003 S


I found the easiest less expensive solution that you should always check first. On my 2003 Rodeo I had the check trans and check 4wd light an ABS light on. Underneath the center console/armrest there is a black box sensor. Right below cup holders. That piece is easily drenched in coffee, water, whatever and causes shorts/ Change that out and a fix to all my problems.

Oct 21, 2011 | 2003 Isuzu Rodeo

1 Answer

I have a 2003 isuzu rodeo. Sometimes it is hard to put into reverse. I can usually get it to work in 1 or 2 tries. the abs light came on a couple of times. what could make this happen?


I do not think shifting gears ,putting your car in reverse has nothing to do whit whit the abs to come on and off ,my isuzu rodeo did the same thing and it was a dirty sensor ABS on front wheels , There is a ring on the inside of the front disc's that works together with the ABS sensor to send information to the car computer when braking ,and must have a distance of about 1/8 of an inch between ring and sensor ,,they must not touch ,what happens is that over time dirt starts to build between sensor and ring ,and ring and sensor begin to touch ,and if they do touch ABS light will start be on and off while driving ,,most of the time the problem is the sensor and not necessarly a bad sensor ,,only a durty sensor and dirty ring ,a broken or loose wire also will activate the ABS light ,,,and about car hard to put into reverse ,you'll probably need a new clutch ,,good luck

Sep 18, 2010 | 2003 Isuzu Rodeo

2 Answers

Isuzu wizard abs light on/off


check the sensors, fron sensors conections right and left ,Also clean sensor ring if sensor ring is dirty it will make contact whit the sensor magnet and abs light will come on and off ,sensor and ring can't not touch if they do touch bicouse o dirt light will como on and off till ring and sensor magnet are cleaned ,,

Mar 17, 2010 | 1999 Isuzu Rodeo

1 Answer

NECESITO AYUDA..PROBLEMA EN ISUZU RODEO 2000.


ami carro sele tiro un sello dela transmision y se tiro todo el aceite lo pare de manejar selo pusieron y ahora enlas suvidas pierde velosidad y prende la luz abs

Feb 18, 2010 | 2003 Isuzu Rodeo

1 Answer

Were is my ABS sensor located on my 2000 Isuzu Rodeo


there should be a sensor at all 4 wheels so make sure there all pluged in 

Jul 03, 2009 | 2000 Isuzu Rodeo

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14378 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...