Question about Isuzu Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees
Posted on Jul 26, 2009
BMW cylinder torque setting all models
According to my service manual as follows.
Cyl head to engine block (torx e12 M10 bolts)
Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees
Cyl head to lower timing chain cover 10nm (89in – lb)
The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.
Posted on Aug 29, 2009
Tips for a great answer:
Jan 03, 2015 | Geo Cars & Trucks
Jan 26, 2014 | 1993 Toyota Corolla
Sep 19, 2013 | 1996 Saturn SL
Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.
Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.
B2500 4 Cylinder
Torque sequence: --------- ' 10 6 2 4 8
' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51
Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final
tighten all bolts an additional 90 to 100 degrees recheck final
torque in sequence *** CAUTION ***engine uses Torque To Yield head
bolts (TTY) that permanently stretch during the initial installation.
New head bolts must be used when cylinder head is replaced or
re-installed to obtain proper torque.
B3000 3.0 6 Cylinder
Torque sequence ---------- ' 6 4 2 8 '
' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen
in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque
to 73 Ft/Lbs
B4000 4.0 6 Cylinder
Torque sequence --------- ' 5 1 3 7 ' '
' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in
sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs
Step 3: turn cylinder head bolts in sequence an additional 90-degrees
recheck final torque in sequence *** CAUTION ***engine uses Torque To
Yield head bolts (TTY) that permanently stretch during the initial
installation. New head bolts must be used when cylinder head is
replaced or re-installed to obtain proper torque.
Good luck with this job!
Feb 06, 2011 | 1998 Mazda Pickup
Nov 26, 2010 | 2004 Chevrolet Impala
May 31, 2010 | 2004 Kia Rio
Mar 06, 2010 | 2001 Chevrolet Venture
Jan 30, 2010 | 2003 Chevrolet Impala
Nov 24, 2009 | 2001 Kia Sportage
Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme
194 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: