Cars & Trucks Logo

Related Topics:

j
jarco Posted on Oct 19, 2013

Ford bantam 1.6 wont start or swing but dash lights comes come on

5 Related Answers

Anonymous

  • 83 Answers
  • Posted on Oct 23, 2009

SOURCE: my 2002 ford explorer wont start. lights come on

first thing to check is the battery and the connections at the battery. if all this checks ok then you should try and look at the fuses for the ignition system. this should get you going in the right direction.

Ad
2smart4u

2smart4u

  • 73 Answers
  • Posted on Dec 04, 2009

SOURCE: my ford bantam wont start everytime it gets wet

gets wet on top or bottom of engine, on top water might of got into the spark ignition system, on bottom, could of got water into a sensor until it dries out, ford are **** wits and want ur money, id take it back and say since that didnt work fix it for free ya ****.

Anonymous

  • 1 Answer
  • Posted on Sep 10, 2011

SOURCE: my 2004 ford explorer wont

got a 2004 ford explorer it wont start but it turns over put fuel pump starter evap canister and purge valve it was broke,and a battery fuel filter,tac system and it still wont crank



Anonymous

  • 1 Answer
  • Posted on Nov 01, 2011

SOURCE: I HAVE AN FORD BANTAM

Anyone with a solution yet?

Anonymous

  • 1 Answer
  • Posted on Oct 24, 2012

SOURCE: 2003 ford taurus dash lights wont come on,windows wont go up and it wont start no power

I would start by checking the fuses in the fuse panel. On the 2003 Taurus it is below and to the left of the steering wheel near the brake pedal.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Hi I drive a ford bantam rocam. while driving the instrument panel went dead. after a while the bakkie wont rev up and died.

Disconnect the battery - negative cable for 5min connect it back and try start it should work
0helpful
1answer

Ford bantam 2008 rocam 1.6 Wont start. Petrol gauge stays on. I think it nhas someting to do with the ignition

Does it have fuel pressure. Have you tested it for fault codes, you do this with a OBD2 code reader, the test connector is under the dash driver side.
2helpful
1answer

Where is the PTM on the ford bantam Utility vehicle 2008?

the Power train module. It is situated by the left foot vent at the bottom. Simply remove cover and it is sitting there

If you need further help, reach me via phone at https://www.6ya.com/expert/cynthia_0eebb7da17b33b5e

0helpful
1answer

Ford bantam completely dead

What exactly does it do when you try to start it?
1helpful
1answer

Ford bantam not starting after it rains

have your battery and charging system checked
0helpful
1answer

Ford bantam

I am assuming that because you can push start it the vehicle is equipped with a manual transmission. There is a safety switch that connect to the clutch pedal in some way. If this switch is defective, unplugged, or bad connection it could inhibit the starting with the key.

When you say you 'start it from the front', what is it you do?
0helpful
1answer

I have a 2006 bantam dash lights tail lights and front park lights not working checked fuses all ok

Hi,i had the same problem and last night i changed the complete light switch unit and all iss working now,so the light switch unit is faulty.
Not finding what you are looking for?

607 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...