Question about Nissan Xterra

Open Question

Suction control vale

I have a 2.2d Yd22 xtrail which has a problem of a flat/dead spot whislt travelling. i saw that it could be a faulty suction control valve situated on the pump. the agents cannot find such a part. can you send me a diagram of the part or the part number

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
oldfishead
  • 155 Answers

SOURCE: my 1990 f150 5.0 has a high pitched whislte sound

most likely the air-by pass is dirty/sticking, while idling tap on the valve and listen for changes in noise, if changing, remove and clean with CHOKE spray and a small brush, if no change, replace the valve......prior to repairs get a HOSE and use it to hear where the noise is coming from...possible vac leak???....hope this helps...GL

Posted on Jul 06, 2009

Ad
  • 1 Answer

SOURCE: I need a Denso SCV (suction control valve) for my

you can buy it in SURESTART DIESEL INJECTION SERVICES address Shaw Lne Industral Estate, Doncaster (01302) 340467

Posted on Nov 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i get a door of a 2005 Nissan Xtrail when the door will not open .It is stuck on the latch/striker.Regards Barry


look at gap on door , if close in one spot put a screw driver in there andtry opening door. some times you may need to get in side and kick it while holding handle in open spot. If rods for handle is off you may need to take panel off. most car to get it off with door closed, remove seat or get a replacement panel and cut a hole in old one to get door. replace door panel.

Oct 01, 2017 | Nissan Cars & Trucks

1 Answer

My 1991 Dodge Dakota has a flat dead spot when you take of from red lights. Where do I start?


The most likely cause would be the throttle position sensor on the throttle body, it is cheap and easy to replace.

Jan 09, 2017 | Dodge Dakota Cars & Trucks

1 Answer

My 54 plate xtrail has a rumbling noise but not exactly sure of the locin sounds more like front n/s gets worse 60-70mph


rumbling noises are an indication of wheel bearing problems
as noise travels it would be best to service all the wheel bearings
check the drive line cv or "U" joints as well

Dec 09, 2016 | Nissan XTrail Cars & Trucks

1 Answer

Fuel needle stays full after doing 70 miles


You may have a "dead spot" on the rheostat track on the sending unit. Once the contact travels past that point, the needle will register properly. The only way to fix it is to replace the sending unit.

Sep 18, 2016 | Cars & Trucks

1 Answer

I had a second hand engine put into my xtrail I was wondering how I could check the accurate kms travelled on the engine without actually seeing the donor car?


You can't. The donor car's computer/odometer would have kept track of the mileage. The engine would not be transplanted with anything that kept any usage records.

Oct 16, 2014 | Cars & Trucks

1 Answer

Nissan x trail yd22 engine timing mark


go to www.automecanico.com translate with your browser this websiste. and ready.

God bless you

Jun 18, 2013 | Cars & Trucks

1 Answer

My s-15 has a dead spot or draw back when it is coasting


Sorry but a ride with a tech is required here.

Jun 12, 2012 | 1987 GMC S-15 Pickup

2 Answers

Bmw 328 series


sounds like a vacuum leak

Robert

Sep 15, 2008 | 1999 BMW 328 Series

2 Answers

1997 dodge 2500 4x4 diesel,12 valve automatic. lock up torque shifts in and out, does the same with over drive off. mostly on a slight grade, or even flat road.(empty or loaded)


my neighbor had the same problem and saturday he had it at a repair place and they found out his onboard computer was faulty he replacved it and has had no more problems

Aug 19, 2008 | 1994 Dodge Ram 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...