Question about Dodge Ram 1500

Open Question

I HAVE AN 06 DODGE RAM 1500 CHECK ENGINE LIGHT CAME ON IT TURNS OFF @ WHEN I STOP @ A LIGHT.. CODES ARE P0344 & P0340

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: trouble codes P0420 P1681 P0344

No I/P Cluster CCD/J1850 Message No CCD/J1850 messages received from the cluster
Received control module

Posted on Sep 18, 2008

  • 373 Answers

SOURCE: 2005 dodge diesel codes!

Hi..
the Code P0340, Camshaft Position sensor problem or Loss signal.
The Code P0341, Camshaft Position sensor Intermitent Signal.

The First step you should do is : Locate the Camsahaft sensor,
Is located On Right Front of the Engine..
It use a 3 wires Connector.
1-- Pink/Yellow
2-- Brown/Orange
3-- Dark blue/Gray.

After you found it. Inspect the Connector. If is The connector in good condition.
Replace the Camshaft Position sensor...

Ok... I hope this help on your problem..
Thank you for use Fixya...

Posted on Sep 27, 2008

Ajkill
  • 2035 Answers

SOURCE: trouble codes

Trouble Code: P0139
O2 (B1 S2) Slow Response
Trouble Code Conditions:Engine started; vehicle driven at 20-55 mph with the throttle open for 2 minutes; ECT at more than 158ºF (70C); catalytic converter temperature is more than 1112F (600C); and EVAP purge is active. O2 Sensor signal voltage switches less than 16 times from lean to rich within 20 seconds during monitoring, or will compare the state of change between the front and rear O2 Sensors and if the differences are greater than a calibrated amount, the DTC will set. 3 good trips are required to turn off the MIL.
Possible Causes:

  • Exhaust leak
  • O2 element is contaminated, deteriorated or it has failed
  • O2 signal circuit or return circuit has failed

Trouble Code: P0344
Camshaft Position Sensor Circuit Intermittent
Trouble Code Conditions:Engine cranking or running; system voltage over 10.5v. The PCM detected an intermittent loss of the CMP Sensor signal during the period of 2.5 complete engine revolutions. The failure counter must reach 20 before this code matures and a code is set.
Possible Causes:
  • Wiring harness fault
  • 5v supply circuit open or shorted to ground
  • Tone wheel/pulse ring is damaged or corroded
  • CMP Sensor has failed
  • CMP Sensor signal circuit is open, shorted to ground or battery voltage or 5v supply
  • CMP Sensor ground circuit is open
  • PCM has failed
  • Trouble Code: P0340
    No Camshaft Position Sensor Circuit Failure
    Trouble Code Conditions:Engine cranking or running, system voltage over 10v. The PCM detected CKP pulses without detecting any CMP Sensor pulses for 5 seconds or 2.5 engine revolutions.
    Possible Causes:
  • CMP Sensor connector is damaged, open or it is shorted
  • CMP Sensor signal circuit is open or shorted to ground or to battery voltage or 5v supply circuit
  • CMP Sensor 5v supply circuit is open or shorted to ground or to battery voltage
  • CMP Sensor ground circuit is open
  • CMP Sensor is damaged or has failed
  • CKP Sensor is damaged or has failed
  • PCM has failed
Good luck....

Posted on Nov 05, 2008

  • 55 Answers

SOURCE: check engine light on code

cheapest thing is get new gas cap, next make sure no vacuum leaks anywhere, the you may need to replace evap purge valve. these systems are junk on all cars and will make you spend lots of money.

Posted on Apr 24, 2009

  • 151 Answers

SOURCE: check engine light on code

This trouble code is Evap Purge System Performance fault. 1) Check for a loose or missing fuel cap. 2) Check for a damaged or missing fuel cap seal. Recheck for other trouble codes. This fault wont cause the stumblering problem. It turns on the MIL lamp to say there leak in the EVAP system.

Posted on May 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 chyrsler 300m it went in limp mode codes p0700. P0340 p0344 p0430 p0888 came up cleared the codes and now it knocks.


clearing codes wont correct the problem and limp mode is designed to protect motor and transmission - p0700 is a transmission problem
P0700 Transmission Control System Malfunction p0340 is camshaft position sensor malfunction
https://www.obd-codes.com/p0340 p0344 is also a camshaft position sensor circuit problem
P0344 Camshaft Position Sensor Circuit Intermittent your p430 is a cat converter problem
https://www.obd-codes.com/p0430 and p0888 is transmission relay problem these reasons are limp mode the knock can be fuel not burning correctly or a lower engine knock can mean you damaged a piston

Nov 08, 2016 | Cars & Trucks

1 Answer

Check engine light codes


Hi Anonymous,this is a PDF can help you Diagnostic Trouble Code Table .This page mainly help you to check the trouble code when you diagnose your car with OBDII diagnostic tools.And you can use Autel MaxiDAS DS708 Update by Internet to help you .

Apr 04, 2014 | 2004 Dodge Ram 1500

1 Answer

2004dodgeram1500 4.7l engine codes p0300 p0304 p0113 p0344


Hello Anonymous,maybe you can read this PDF ,it can help you,
Diagnostic Trouble Code Table .

Apr 04, 2014 | 2004 Dodge Ram 1500

1 Answer

P0340 code and p0344 on 3.7 dodge Dakota


First check the easy thing. Have your battery tested. Sensors very sensitive to failing battery. If the battery tests fine then you will need to change the Cam sensor probably a $30 part. On your truck remove the air filter housing & the cam sensor should be easily accessible at the front of the cyl head. Hope this works for you. Based on your P codes it should.

Mar 25, 2014 | 2004 Dodge Dakota

1 Answer

Stalling wont idle


  • egr valve
  • egr sensor
  • cam shaft sensor
  • barometric pressure sensor (map sensor)
vacuum leak somewhere, out of time, broken timing belt or missing teeth.

Dec 12, 2013 | Cars & Trucks

1 Answer

Neon Code P0344


I believe that the splice for the cam sensor is about 8 inches back in the harness. Power to the cam supplies several sensors. I have fixed a few that the splice was bad, There is very little room to work in to get to the splice, but it's not impossible to fix.

Jul 13, 2013 | 2004 Dodge Neon

1 Answer

Mustang error codes P0340 , P0344


These are camshaft position sensor codes. Replace camshaft sensor.

Apr 18, 2017 | 2006 Ford Mustang GT

1 Answer

I have a 05 Dodge ram 1500 90,000mi. and it start to bog and eng.light came on my codes were p0129-p0405-p0340-p0868 and pending codes were p0129-p0325-p0330-p0405-p0340. I had put a new map sensor in...


P0340 is for camshaft position sensor circuit malfunction so the problem can be in you hav already changed sensor, then you need to check wiring from sensor to ecu and if the wires are ok than check the ecu! It can be either of them cousing the problem.

Jan 30, 2011 | Dodge Ram 1500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...