Question about Hyundai Motor 1998 Accent

# Wants the cylinder head torque specification in newton meters

Posted by Anonymous on

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
goodluck!

Posted on Jan 02, 2017

1998 Hyundai Lantra "G4GM" engine 1795cc.there are two heads or blocks, one is called the M10, other is the M12, figure out which one you have cause the torque is different for stage one by 5nm........... Dont get confused theres 2 different engines so 2 different torques for stage1---------
heres the full details: Stage 1 - m10 = 30nm / m12 = 35nm-------------------------- -------- Stage 2 - tighten by 60-65 degrees ------------ stage 3 - tighten by 60-65 degrees. no sequence is given in the data book for tightening so go off what you thinks right, it doesn't matter on this engine.

Posted on Jan 26, 2010

Testimonial: "Very accurate answer. Thanks, all is well now"

1 kilogram meter = 7.233 013 831 6 pound foot

you can use a online converter like the http://www.onlineconversion.com/torque.htm

3.5 kilogram meter = 25.315 548 411 pound foot
4.5 kilogram meter = 32.548 562 242 pound foot

Posted on Jan 28, 2010

Testimonial: "Thanks,very help full + on line converter info grate. "

You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Posted on Feb 19, 2010

Are you aware that besides the torque, the cylider head bolts MUST be torqued in a specific sequence. The Ft/lbs of torque and the sequence are only available in the cars service manual or something similar like Chiltons repair manual. You can browse a copy of the Chiltons at a local library or bookstore and write down the ft/lbs and sequence. I've done it myself to save a few bucks

Posted on Mar 08, 2010

4 cylinder? 10 bolts? This is generic. Starting in the center, top first then bottom, move over one position left or right top then make an "X" to the opposite side bottom. Then up and "x" back to bottom. One more "x" pattern for four remaning outside bolts. Final torque around 60 ft/lbs (generally)
Curious, how are you doing this without a repair manual? Tisk tisk.

Posted on Mar 25, 2010

×

my-video-file.mp4

×

## Related Questions:

### Cylinder head bolt tension for 2010 Mitsubishi FN64F 6M60-3AT2

The term you mean is actually torque. Cylinder head torque is usually specified in foot pounds, or in the metric world, newton meters. It describes how much twisting force should be applied to tighten the head bolts.

www.engineaustrailia.com.au/products/diesel-engine-parts/mitsubishi

Apr 20, 2017 | Mitsubishi Cars & Trucks

### I need to know what tool or torque wrench to use

nm is newton/meters but degrees are not relevant to torque it is a function of temperature. I suggest you verify your information 1st B4 you attempt. To much or to little and you can cause a great deal of damage.

Sep 28, 2014 | Cars & Trucks

### Can't find the torque head bolt pattern for a 1996 gmc sierra 5.7 vortex

The "pattern" for ANY cylinder head is pretty much the same...start with the bolts in the center of the head and work your way out to both ends.
Torquing the cylinder head on your 5.7L Vortec engine to manufacturer specifications requires the use of a "torque angle" gauge, as well as a traditional torque meter.

The torque specifications are as follows:

> Step 1: All bolts: 22 Ft Lbs (30 Nm.)
> Step 2: Short bolts: Additional 55 degrees; Medium bolts: Additional 65 degrees; Long bolts: Additional 75 degrees

May 20, 2012 | GMC Sierra 1500 Cars & Trucks

### Cylinder head bolt torque setting

The confusion may have come from a number of possible sources.

For the 2.5 Liter engine, the bolt tension is 80 Foot pounds or 108 Newton meters. cold engine only. No retorque and No retorque when hot.

This is from the Auto Engine Rebuilders Association literature.

Jan 07, 2012 | Cars & Trucks

### Vw jetta 2007 bkd engine whatare cylinder head bolt torque settings

I had a quick look online for these specs. according to several sites I visited, these are the correct specs.. Have fun.. 1.8L Turbo
• Volkswagon's 1.8-liter Turbo engine has 10 head bolts arranged in pairs across the engine. The bolts should first be pre-tightened to a specification of 40 Newton Meters (Nm), starting with the middle two bolts and proceeding in sequence out towards either the left or right end of the engine. The bolts should then be tightened again in the same sequential order by making a one-quarter turn of the wrench, and then tightened once again with another one-quarter turn.
• 2.8L V6
• There are 20 head bolts arranged in three lines across Volkswagon's 2.8-liter V6 engine. The bolts should first be pre-tightened in sequence to a specification of 50 Newton Meters (N-m), starting with the first bolt that is situated in the center of the engine block between cylinders 3 and 4. Proceed tightening the bolts in sequence out towards either the left or right end of the engine. The bolts should then be tightened again in the same sequential order by making a one-quarter turn of the wrench, and then tightened once again with another one-quarter turn.
• 2.0L L4
• Volkswagon's 2.0-liter L4 engine has 10 bolts that are arranged in pairs across the engine. The bolts should first be pre-tightened in sequence to a specification of 40 Newton Meters (N-m), starting with the middle two bolts and proceeding in sequence out towards either left or right end of the engine. The bolts should then be tightened again in the same sequential order by making a one-quarter turn using a box wrench, and then tightened again with another one-quarter turn.
• Dec 19, 2010 | 2007 Volkswagen Jetta 2.5 Sedan

Please don't forget to rate. Thank you:

Cylinder head bolt torque sequence—3.4L engine

• Cylinder head by aligning it with the dowel pins
• New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
• Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
• Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).

• Right side rear cylinder head:

Cylinder head bolt torque sequence—3.4L engine

• Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
• New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
• Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
• Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
• Spark plug wires
• Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
• Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
• Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
• Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
• Mar 06, 2010 | 2001 Chevrolet Venture

### I LOOKED UP THE TORQUE SETTING FOR THR HUB NUT FOR A 1999 FORD TAURUS.IT IS 184/250 ftlbs/NM. CAN YOU EXPLAIN WHAT THE ''NM'' MEANS ? ALSO, WHAT IS THE TORQUE SETTING FOR THE 3 HUB BOLTS?

What "NM" means is Newton Meters; it's the metric measurement equal to the standard measurement. You interpret the torque settings like this 184 ft lbs OR 250 Newton Meters.

The three hub bolts should be tightened to, I believe, 80 ft lbs OR 110 Newton Meters

Oct 23, 2009 | 1999 Ford Taurus

### Where is the gas filter located on a 2003/ 4 door - having problem putting gas into the car

Almost every newer vehicle has the fuel filter in the top of the fuel tank. Good luck

Oct 16, 2009 | 2003 Pontiac Sunfire

### I need torque specs for head bolts on 1992 merc benz 230 e

hello,230e with engine 102.982,cylinder head bolt,double hexagonal socket m12, stage 1, 55 newton meter,stage 2 90 degrees stage 3 90 degrees,4 pcs. bolt with m8 tighten to 25 nm.ref. technical data year 1993,ty

Apr 17, 2009 | 1992 Mercedes-Benz E-Class

## Open Questions:

#### Related Topics:

16 people viewed this question

#### Top Hyundai Experts

Level 3 Expert

##### Colin Stickland

Level 3 Expert