Question about Fiat Strada

Open Question

Diagram showing timing position of Fiat Siena El 16 valve Camshafts

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 8 Answers

SOURCE: Timing for tropper 6cly and 4 camshafts and 24 valves model 2000

Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Posted on Mar 28, 2009

Ad
ghost45
  • 1280 Answers

SOURCE: timing belt diagram

Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Posted on Oct 18, 2009

mastericpr08
  • 571 Answers

SOURCE: need to know where/how the timing marks should be

must be located in the damper (front bottom of engine)but first you need the timming pistol

Posted on Oct 22, 2010

  • 20 Answers

SOURCE: i need the diagram that

THE BEST THING TO DO IS GO TO AUTO ZONE OR ANY PARTS STORE AND PURCHASE A MANUEL FOR THAT VIHICLE COSTS ABOUT 28 DOLLARS WORTH THE WEIGHT IN GOLD

Posted on Oct 25, 2010

alicantecoli
  • 22246 Answers

SOURCE: My fiat siena EL 1.6

yes its a fuel fault but whats causing it i have no idea and as this is a europen market vehicle then its a dealer only job to find the fault as the whole vehicle is using encrypted software so its impossible to diagnose unless youm have a prior knowledge of the faults that can occur with this vehicle ,i would suspect a problem with overfueling and the main cause of this is the autochoke but weither its a sensor fault or a control fault i have no idea but i would change the autochoke temperature sensor and see what happens

Posted on Feb 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car fiat siena 16 valves just revv it self when the engen is warm


Go to online store reliable they have repair manuals I am sure you will get the solution.
Here's the link
Best Manuals

Sep 22, 2017 | Fiat Cars & Trucks

1 Answer

What's your question?what causes fiat siena 1,2 mpi EL to misfire and injecter light stays on?


im not a rocket scientist but one of the injectors is clogged/not working thus making that cylinder not fire

Nov 28, 2015 | Fiat Cars & Trucks

1 Answer

How to set cam timing on fiat siena elx 2002 model 1600 16 valve


cam and crank should have marks on them . buy a manual and read up on setting the timing .

Jul 09, 2015 | Fiat Cars & Trucks

1 Answer

Camshaft valve timing marks for Fiat Siena 1.6 16V, 1995 to 2002 model


there are no timing marks for camshafts you need a fiat tool to lock the cams rear of engine but if you mark the cam sprockets carefully before you dismantle you should be ok if not borrow the fiat tools the crankshaft marks are on the front pulley end about @aprox.10oclock position

May 27, 2015 | Fiat Siena Cars & Trucks

1 Answer

Diagnostic plug for fiat Siena EL 1.2 model 2000


so you want to know where it is??? k?? your question isnt good
not at all

and shows nothing.. asks for really nothing

Apr 25, 2015 | Fiat Cars & Trucks

1 Answer

Engine diagram fiat siena


our fiat 2001 1.6 refuses too keep da idle

May 08, 2013 | 2005 Fiat Siena 1.6

1 Answer

I am looking for a fiat siena 1.6V 1600, 16valve timing diagram


There is no such timing diagram in particular is provided except the R&D or the manufacturer, but the marking on the engine is mandatory, and its being well marked for the technicians on the assembly floor and service work shops, Service man has more brains than R&D fellow coz understanding other persons doings more efforts or you can say following some body's car is more difficult than..........

Jan 11, 2013 | 2005 Fiat Siena 1.6

1 Answer

Timing diagram for a fiat siena 1600 16valve


You need a timing kit in order to lock de camshafts and the crankshaft; as far as I know, there's not timings marks on the gears.

Jan 11, 2013 | Fiat Siena Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...