Question about Nissan Cars & Trucks

Open Question

09 Nissan Altima 2.5s with diagnostic code reading P3231 and P0826

Posted by Anonymous on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: problem code p1320 came up on my diagnostic

sounds like one of your ignition coils are starting to fail, try and find a good price for all 6 on ebay

MIL (check engine light) "ON" with DTC P1320 stored in the ECM Intermittent spark knock (detonation)

  • Check the ECCS wiring harness for a broken or damaged wire.
    1. If the ECCS harness has a broken or damaged wire that is causing the symptom(s) noted above, repair the harness and verify the incident is resolved.
    2. If the ECCS harness does not have a broken or damaged wire and is NOT causing the symptom(s) listed above, proceed with step 3 below.
  • Replace ignition coil(s) with the one(s) listed in the Parts Information table, and verify the incident is resolved.

  • Posted on Dec 03, 2009

    • 101 Answers

    SOURCE: Nissan x-trail fault codes that

    p0725=engine speed input circuit.p0826=up and down switch input circuit.ime not sure what the other 2 codes are sorry.

    Posted on Sep 05, 2010

    Add Your Answer

    Uploading: 0%


    Complete. Click "Add" to insert your video. Add



    Related Questions:

    1 Answer

    P0826 Nissan - Rogue 2009

    P0826 Nissan - Manual Mode Switch Circuit
    Possible causes: - Faulty Manual mode select switch (Built into control device, shifter)
    - Faulty Manual mode position select switch (Built into control device, shifter)
    - Faulty Control Device (Shifter)
    - Control Device harness is open or shorted
    - Control Device circuit poor electrical connection

    When is the code detected? When an impossible pattern of switch signals is detected, a malfunction is detected.

    Possible symptoms: - Engine Light ON (or Service Engine Soon Warning Light)

    P0826 Nissan Description: Manual mode switch is installed in shift control device. The manual mode switch sends shift up and shift down switch signals to Transmission Control Module (TCM) with Control Area Network (CAN) communication.

    TCM sends the switch signals to combination meter via CAN communication line. Then manual mode switch position is indicated on the shift position indicator.

    P0826 Nissan Manual Mode Switch Circuit

    May 31, 2015 | 2009 Nissan Rogue

    1 Answer

    What would cause 2012 nissan altima to have no power to obd?

    1999 all other models to 2000.the data link on Nissan have to switched on at the side of the ECM that is turned by a screw driver . The procedure is to access the ECM -switch ignition on(do not start engine)--turn diagnostic mode selector on ECM fully clockwise.--wait 2 seconds--turn diagnostic mode selector on ECM fully counter clockwise. Lights will flash a code of long and short models 20002001 and on can only be read by a scan tool connected to a data link connector.

    Jul 28, 2014 | 2012 Nissan Altima 2.5 Sedan 2.5L 4-cyl....

    1 Answer

    Code p0725 p0826

    Here's a LINK to code P0725.Here's CODE P0826.

    Aug 21, 2013 | 2008 Nissan Rogue

    1 Answer

    Nissan altima p0725

    P0725 - Nissan Type Powertrain - Transmission - ISO/SAE Controlled Description Engine speed (RPM) - incorrect voltage signal ECM to TCM
    Cause Wiring, RPM sensor, TCM, ECM
    P0720 - Nissan Type Powertrain - Transmission - ISO/SAE Controlled Description AT - vehicle speed sensor (VSS)
    Cause Wiring, VSS, TCM
    P0710 - Nissan Type Powertrain - Transmission - ISO/SAE Controlled Description Transmission fluid temperature sensor - excessively high or low voltage
    Cause Wiring, temperature sensor, TCM, ECM
    P0826 - Generic Type Powertrain - Transmission - ISO/SAE Controlled Description Up and Down Shift Switch Circuit

    the dtcs of your car are so many, my best suggest is go to garage for repair. or if you would like to repair by yourself, you need to buy a diagnostic tool such as multidiag j2534

    Jul 07, 2013 | Cars & Trucks

    1 Answer

    2000 nissasn altima service engine soon light came on car has been struttering when iam at lights engine is running much harder than usual to the point when i am idoling the hood shakes.any ideas?

    You will need to get the check engine light code from the car's computer, without this code the options for what's wrong are almost endless. A scan tool must be used to do this. You can go to a dealership where they will be able to perform a full diagnostic, or an independent shop (either are fine), or for free you could go to an Advance Auto Parts or AutoZone and have the code read but no diagnostic done. I would recommend not driving it too much until you can get this code read to find out what system of the car is malfunctioning.

    Apr 08, 2011 | 2000 Nissan Altima

    2 Answers

    Check engine light is on 2000 nissan altima

    Get codes read @ autozone or simular parts place to get a direction of what your problem might be.

    Jan 23, 2011 | 2000 Nissan Altima

    1 Answer

    I have check engine diagnostic code c1000e on Nissan Altima 2002. what does the code mean? The vehicle drives and reverses but stuck on D4. The check engine light is on and the OBD2 test shows code c1000...

    hi, C1000- Engine; CAN Communication Circuit.

    That and maybe water got into a connector. Maybe the AWD connector. Be sure to read the LAN System section in the SM. and the TF transfer section. Sounds like the CAN line going to the AWD clutch got shorted or opened. Problem is the full diagnostics need the Consult 4. I think may be it can help you.

    Sep 04, 2010 | 2002 Nissan Altima

    1 Answer

    3rd blown drivers side low beam headlight


    Apr 07, 2009 | 2002 Nissan Altima

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    658 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts


    Level 3 Expert

    77202 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    726 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides